linux/drivers/ata, branch v4.15

libata: apply MAX_SEC_1024 to all LITEON EP1 series devices

2017-12-19T13:30:38Z

LITEON EP1 has the same timeout issues as CX1 series devices. Revert max_sectors to the value of 1024. 'e0edc8c54646 ("libata: apply MAX_SEC_1024 to all CX1-JB*-HP devices")' Signed-off-by: Xinyu Lin Signed-off-by: Tejun Heo Cc: stable@vger.kernel.org

libata: sata_down_spd_limit should return if driver has not recorded sstatus speed

2017-12-04T21:57:03Z

During hotplug, it is possible for 6Gbps link speed to be limited all the way down to 1.5 Gbps which may lead to a slower link speed when drive is re-connected. This behavior has been seen on a Intel Lewisburg SATA controller (8086:a1d2) with HGST HUH728080ALE600 drive where SATA link speed was limited to 1.5 Gbps and when re-connected the link came up 3.0 Gbps. This patch was retested on above configuration and showed the hotplugged link to come back online at max speed (6Gbps). I did not see the downgrade when testing on Intel C600/X79, but retested patched linux-4.14-rc5 kernel and didn't see any side effects from this change. Also, successfully retested hotplug on port multiplier 3Gbps link. tj: Minor comment updates. Signed-off-by: David Milburn Signed-off-by: Tejun Heo

ahci: mtk: Change driver name to ahci-mtk

2017-12-04T20:35:29Z

The driver name "ahci" is already used by the ahci platform driver. This leads to the following error: Error: Driver 'ahci' is already registered, aborting... Change the name to ahci-mtk to fix this. Signed-off-by: Matthias Brugger Signed-off-by: Tejun Heo

ahci: qoriq: refine port register configuration

2017-12-04T20:18:08Z

These PP2C and PP3C registers control the configuration of the PHY control OOB timing for the COMINIT/COMWAKE parameters respectively for sata port. Overwrite default values with calculated ones to get better OOB timing. Signed-off-by: Tang Yuantian Signed-off-by: Tejun Heo

pata_pdc2027x : make pdc2027x_*_timing structures const

2017-11-27T19:46:26Z

Make these pdc2027x_*_timing structures const as it is never modified. Signed-off-by: Arvind Yadav Signed-off-by: Tejun Heo

pata_pdc2027x: Remove unnecessary error check

2017-11-27T19:46:26Z

Here, The function pdc_hardware_init always return zero. So it is not necessary to check its return value. Signed-off-by: Arvind Yadav Signed-off-by: Tejun Heo

ata: mediatek: Fix typo in module description

2017-11-27T19:26:59Z

Signed-off-by: Albert Pool Signed-off-by: Tejun Heo

Merge branch 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

2017-11-15T22:11:41Z

Pull libata updates from Tejun Heo: "Nothing too interesting or alarming. Other than a new power saving mode addition to ahci and crash fix on a tracepoint, all changes are trivial or device-specific" * 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits) ahci: imx: Handle increased read failures for IMX53 temperature sensor in low frequency mode. ata: sata_dwc_460ex: Propagate platform device ID to DMA driver ata: fixes kernel crash while tracing ata_eh_link_autopsy event ata: pata_pdc2027x: Fix space before '[' error. libata: fix spelling mistake: 'ambigious' -> 'ambiguous' ata: ceva: Add SMMU support for SATA IP ata: ceva: Correct the suspend and resume logic for SATA ata: ceva: Correct the AXI bus configuration for SATA ports ata: ceva: Add CCI support for SATA if CCI is enabled ata: ceva: Make RxWaterMark value as module parameter ata: ceva: Disable Device Sleep capability ata: ceva: Add gen 3 mode support in driver ata: ceva: Move sata port phy oob settings to device-tree devicetree: bindings: Add sata port phy config parameters in ahci-ceva ata: mark expected switch fall-throughs ata: sata_mv: remove a redundant assignment to pointer ehi ahci: Add support for Cavium's fifth generation SATA controller ata: sata_rcar: Use of_device_get_match_data() helper libata: make ata_port_type const libata: make static arrays const, reduces object code size ...

Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

2017-11-14T01:56:58Z

Pull timer updates from Thomas Gleixner: "Yet another big pile of changes: - More year 2038 work from Arnd slowly reaching the point where we need to think about the syscalls themself. - A new timer function which allows to conditionally (re)arm a timer only when it's either not running or the new expiry time is sooner than the armed expiry time. This allows to use a single timer for multiple timeout requirements w/o caring about the first expiry time at the call site. - A new NMI safe accessor to clock real time for the printk timestamp work. Can be used by tracing, perf as well if required. - A large number of timer setup conversions from Kees which got collected here because either maintainers requested so or they simply got ignored. As Kees pointed out already there are a few trivial merge conflicts and some redundant commits which was unavoidable due to the size of this conversion effort. - Avoid a redundant iteration in the timer wheel softirq processing. - Provide a mechanism to treat RTC implementations depending on their hardware properties, i.e. don't inflict the write at the 0.5 seconds boundary which originates from the PC CMOS RTC to all RTCs. No functional change as drivers need to be updated separately. - The usual small updates to core code clocksource drivers. Nothing really exciting" * 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits) timers: Add a function to start/reduce a timer pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday() timer: Prepare to change all DEFINE_TIMER() callbacks netfilter: ipvs: Convert timers to use timer_setup() scsi: qla2xxx: Convert timers to use timer_setup() block/aoe: discover_timer: Convert timers to use timer_setup() ide: Convert timers to use timer_setup() drbd: Convert timers to use timer_setup() mailbox: Convert timers to use timer_setup() crypto: Convert timers to use timer_setup() drivers/pcmcia: omap1: Fix error in automated timer conversion ARM: footbridge: Fix typo in timer conversion drivers/sgi-xp: Convert timers to use timer_setup() drivers/pcmcia: Convert timers to use timer_setup() drivers/memstick: Convert timers to use timer_setup() drivers/macintosh: Convert timers to use timer_setup() hwrng/xgene-rng: Convert timers to use timer_setup() auxdisplay: Convert timers to use timer_setup() sparc/led: Convert timers to use timer_setup() mips: ip22/32: Convert timers to use timer_setup() ...

ahci: imx: Handle increased read failures for IMX53 temperature sensor in low frequency mode.

2017-11-13T20:17:43Z

Extended testing has shown that the imx ahci driver sometimes requires more than the 100 attempts currently alotted in the driver to perform a successful temperature reading when running at minimum (throttled) CPU frequency. Debugging suggests that the read cycle can take 160 attempts (which given that the driver averages 80 readings from the ADC equates to one failure on each read). Increase the attempt limit to 200 in order to greatly reduce the likelihood of the driver failing to perform a temperature reading, especially at low CPU frequency. Signed-off-by: Egor Starkov Signed-off-by: Martyn Welch Signed-off-by: Tejun Heo