linux/drivers/ata, branch v6.8

ata: libata-core: Do not call ata_dev_power_set_standby() twice

2024-02-21T18:09:17Z

For regular system shutdown, ata_dev_power_set_standby() will be executed twice: once the scsi device is removed and another when ata_pci_shutdown_one() executes and EH completes unloading the devices. Make the second call to ata_dev_power_set_standby() do nothing by using ata_dev_power_is_active() and return if the device is already in standby. Fixes: 2da4c5e24e86 ("ata: libata-core: Improve ata_dev_power_set_active()") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal Signed-off-by: Niklas Cassel

ata: ahci_ceva: fix error handling for Xilinx GT PHY support

2024-02-19T09:44:37Z

Platform clock and phy error resources are not cleaned up in Xilinx GT PHY error path. To fix introduce the function ceva_ahci_platform_enable_resources() which is a customized version of ahci_platform_enable_resources() and inline with SATA IP programming sequence it does: - Assert SATA reset - Program PS GTR phy - Bring SATA by de-asserting the reset - Wait for GT lane PLL to be locked ceva_ahci_platform_enable_resources() is also used in the resume path as the same SATA programming sequence (as in probe) should be followed. Also cleanup the mixed usage of ahci_platform_enable_resources() and custom implementation in the probe function as both are not required. Fixes: 9a9d3abe24bb ("ata: ahci: ceva: Update the driver to support xilinx GT phy") Signed-off-by: Radhey Shyam Pandey Reviewed-by: Damien Le Moal Signed-off-by: Niklas Cassel

ahci: asm1064: correct count of reported ports

2024-02-19T09:14:31Z

The ASM1064 SATA host controller always reports wrongly, that it has 24 ports. But in reality, it only has four ports. before: ahci 0000:04:00.0: SSS flag set, parallel bus scan disabled ahci 0000:04:00.0: AHCI 0001.0301 32 slots 24 ports 6 Gbps 0xffff0f impl SATA mode ahci 0000:04:00.0: flags: 64bit ncq sntf stag pm led only pio sxs deso sadm sds apst after: ahci 0000:04:00.0: ASM1064 has only four ports ahci 0000:04:00.0: forcing port_map 0xffff0f -> 0xf ahci 0000:04:00.0: SSS flag set, parallel bus scan disabled ahci 0000:04:00.0: AHCI 0001.0301 32 slots 24 ports 6 Gbps 0xf impl SATA mode ahci 0000:04:00.0: flags: 64bit ncq sntf stag pm led only pio sxs deso sadm sds apst Signed-off-by: "Andrey Jr. Melnikov" Signed-off-by: Niklas Cassel

ata: libata-core: Do not try to set sleeping devices to standby

2024-02-14T10:02:08Z

In ata ata_dev_power_set_standby(), check that the target device is not sleeping. If it is, there is no need to do anything. Fixes: aa3998dbeb3a ("ata: libata-scsi: Disable scsi device manage_system_start_stop") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal Signed-off-by: Niklas Cassel

ahci: Extend ASM1061 43-bit DMA address quirk to other ASM106x parts

2024-01-31T11:09:34Z

ASMedia have confirmed that all ASM106x parts currently listed in ahci_pci_tbl[] suffer from the 43-bit DMA address limitation that we ran into on the ASM1061, and therefore, we need to apply the quirk added by commit 20730e9b2778 ("ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers") to the other supported ASM106x parts as well. Cc: stable@vger.kernel.org Link: https://lore.kernel.org/linux-ide/ZbopwKZJAKQRA4Xv@x1-carbon/ Signed-off-by: Lennert Buytenhek [cassel: add link to ASMedia confirmation email] Signed-off-by: Niklas Cassel

ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers

2024-01-25T15:59:09Z

With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was observed that was immediately preceded by the following kernel messages: ahci 0000:28:00.0: Using 64-bit DMA addresses ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00000 flags=0x0000] ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00300 flags=0x0000] ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00380 flags=0x0000] ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00400 flags=0x0000] ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00680 flags=0x0000] ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00700 flags=0x0000] The first message is produced by code in drivers/iommu/dma-iommu.c which is accompanied by the following comment that seems to apply: /* * Try to use all the 32-bit PCI addresses first. The original SAC vs. * DAC reasoning loses relevance with PCIe, but enough hardware and * firmware bugs are still lurking out there that it's safest not to * venture into the 64-bit space until necessary. * * If your device goes wrong after seeing the notice then likely either * its driver is not setting DMA masks accurately, the hardware has * some inherent bug in handling >32-bit addresses, or not all the * expected address bits are wired up between the device and the IOMMU. */ Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual address 0xffffffff00000000 produces the following I/O page faults: vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000000 flags=0x0010] vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000500 flags=0x0010] Note that the upper 21 bits of the logged DMA address are zero. (When asking a different PCIe device in the same PCIe slot to DMA to the same I/O virtual address, we do see all the upper 32 bits of the DMA address as 1, so this is not an issue with the chipset or IOMMU configuration on the test system.) Also, hacking libahci to always set the upper 21 bits of all DMA addresses to 1 produces no discernible effect on the behavior of the ASM1061, and mkfs/mount/scrub/etc work as without this hack. This all strongly suggests that the ASM1061 has a 43 bit DMA address limit, and this commit therefore adds a quirk to deal with this limit. This issue probably applies to (some of) the other supported ASMedia parts as well, but we limit it to the PCI IDs known to refer to ASM1061 parts, as that's the only part we know for sure to be affected by this issue at this point. Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/ Signed-off-by: Lennert Buytenhek [cassel: drop date from error messages in commit log] Signed-off-by: Niklas Cassel

ahci: asm1166: correct count of reported ports

2024-01-24T07:53:55Z

The ASM1166 SATA host controller always reports wrongly, that it has 32 ports. But in reality, it only has six ports. This seems to be a hardware issue, as all tested ASM1166 SATA host controllers reports such high count of ports. Example output: ahci 0000:09:00.0: AHCI 0001.0301 32 slots 32 ports 6 Gbps 0xffffff3f impl SATA mode. By adjusting the port_map, the count is limited to six ports. New output: ahci 0000:09:00.0: AHCI 0001.0301 32 slots 32 ports 6 Gbps 0x3f impl SATA mode. Closes: https://bugzilla.kernel.org/show_bug.cgi?id=211873 Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218346 Signed-off-by: Conrad Kostecki Reviewed-by: Hans de Goede Signed-off-by: Niklas Cassel

ata: libata-sata: improve sysfs description for ATA_LPM_UNKNOWN

2024-01-22T21:26:03Z

Currently, both ATA_LPM_UNKNOWN (0) and ATA_LPM_MAX_POWER (1) displays as "max_performance" in sysfs. This is quite misleading as they are not the same. For ATA_LPM_UNKNOWN, ata_eh_set_lpm() will not be called at all, leaving the configuration in unknown state. For ATA_LPM_MAX_POWER, ata_eh_set_lpm() is called, and setting the policy to ATA_LPM_MAX_POWER. This also matches the description of the SATA_MOBILE_LPM_POLICY Kconfig: 0 => Keep firmware settings 1 => Maximum performance Thus, update the sysfs description for ATA_LPM_UNKNOWN to match reality. While at it, update libata.h to mention that the ascii descriptions are in libata-sata.c and not in libata-scsi.c. Reviewed-by: Damien Le Moal Signed-off-by: Niklas Cassel

Merge tag 'ata-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux

2024-01-11T21:49:00Z

Pull ata updates from Damien Le Moal: - Cleanup the pxa PATA driver to use dma_request_chan() instead of the deprecated dma_request_slave_channel(). - Add Niklas as co-maintainer of the ata subsystem. * tag 'ata-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux: MAINTAINERS: Add Niklas Cassel as libata maintainer ata: pata_pxa: convert not to use dma_request_slave_channel()

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2023-12-01T21:27:20Z

Pull SCSI fixes from James Bottomley: "Three small fixes, one in drivers. The core changes are to the internal representation of flags in scsi_devices which removes space wasting bools in favour of single bit flags and to add a flag to force a runtime resume which is used by ATA devices" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: sd: Fix system start for ATA devices scsi: Change SCSI device boolean fields to single bit flags scsi: ufs: core: Clear cmd if abort succeeds in MCQ mode