linux/drivers/bcma, branch v6.3

driver core: make struct bus_type.uevent() take a const *

2023-01-27T12:45:52Z

The uevent() callback in struct bus_type should not be modifying the device that is passed into it, so mark it as a const * and propagate the function signature changes out into all relevant subsystems that use this callback. Acked-by: Rafael J. Wysocki Acked-by: Hans de Goede Link: https://lore.kernel.org/r/20230111113018.459199-16-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman

bcma: Fail probe if GPIO subdriver fails

2022-11-04T10:59:51Z

We currently register the BCMA core even if the GPIO portions fail. There is no reason for this: the GPIO should register just fine, if it fails the BCMA driver should fail. We already gracefully handle the case where the GPIO driver is not compiled in. Signed-off-by: Linus Walleij Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20221028093000.239020-1-linus.walleij@linaro.org

Kalle Valo says:

2022-10-29T01:31:40Z

==================== pull-request: wireless-next-2022-10-28 First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7. All mac80211 driver are now converted to use internal TX queues, this might cause some regressions so we wanted to do this early in the cycle. Note: wireless tree was merged[1] to wireless-next to avoid some conflicts with mac80211 patches between the trees. Unfortunately there are still two smaller conflicts in net/mac80211/util.c which Stephen also reported[2]. In the first conflict initialise scratch_len to "params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and in the second conflict take the version which uses elems->scratch_pos. [1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91 [2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/ mac80211 - preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues - add API to show the link STAs in debugfs - all mac80211 drivers are now using mac80211 internal TX queues (iTXQs) rtw89 - support 8852BE rtl8xxxu - support RTL8188FU brmfmac - support two station interfaces concurrently bcma - support SPROM rev 11 ==================== Link: https://lore.kernel.org/r/20221028132943.304ECC433B5@smtp.kernel.org Signed-off-by: Jakub Kicinski

bcma: gpio: Convert to immutable gpio irqchip

2022-10-19T06:02:18Z

This switches the BCMA gpio irqchip to be immutable. The GPIO subsystem plays tricks on the irqchip structures, and we're fixing it one driver at a time. See merge commit 4bde53ab3370 ("Merge branch irq/gpio-immutable into irq/irqchip-next") for all the details. Tested on the D-Link DWL-6810AP. Cc: Marc Zyngier Cc: Bartosz Golaszewski Cc: Rafał Miłecki Signed-off-by: Linus Walleij Acked-by: Marc Zyngier Reviewed-by: Bartosz Golaszewski Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20221012192348.2234478-1-linus.walleij@linaro.org

bcma: support SPROM rev 11

2022-10-19T05:59:37Z

Rev 11 works fine for me to set the MAC address of gmac0 and gmac1 in the D-Link DWL-8610AP. Cc: Rafał Miłecki Signed-off-by: Linus Walleij Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20221011122941.2053705-1-linus.walleij@linaro.org

Merge tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

2022-10-12T17:23:24Z

Pull interrupt updates from Thomas Gleixner: "Core code: - Provide a generic wrapper which can be utilized in drivers to handle the problem of force threaded demultiplex interrupts on RT enabled kernels. This avoids conditionals and horrible quirks in drivers all over the place - Fix up affected pinctrl and GPIO drivers to make them cleanly RT safe Interrupt drivers: - A new driver for the FSL MU platform specific MSI implementation - Make irqchip_init() available for pure ACPI based systems - Provide a functional DT binding for the Realtek RTL interrupt chip - The usual DT updates and small code improvements all over the place" * tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits) irqchip: IMX_MU_MSI should depend on ARCH_MXC irqchip/imx-mu-msi: Fix wrong register offset for 8ulp irqchip/ls-extirq: Fix invalid wait context by avoiding to use regmap dt-bindings: irqchip: Describe the IMX MU block as a MSI controller irqchip: Add IMX MU MSI controller driver dt-bindings: irqchip: renesas,irqc: Add r8a779g0 support irqchip/gic-v3: Fix typo in comment dt-bindings: interrupt-controller: ti,sci-intr: Fix missing reg property in the binding dt-bindings: irqchip: ti,sci-inta: Fix warning for missing #interrupt-cells irqchip: Allow extra fields to be passed to IRQCHIP_PLATFORM_DRIVER_END platform-msi: Export symbol platform_msi_create_irq_domain() irqchip/realtek-rtl: use parent interrupts dt-bindings: interrupt-controller: realtek,rtl-intc: require parents irqchip/realtek-rtl: use irq_domain_add_linear() irqchip: Make irqchip_init() usable on pure ACPI systems bcma: gpio: Use generic_handle_irq_safe() gpio: mlxbf2: Use generic_handle_irq_safe() platform/x86: intel_int0002_vgpio: Use generic_handle_irq_safe() ssb: gpio: Use generic_handle_irq_safe() pinctrl: amd: Use generic_handle_irq_safe() ...

bcma: gpio: Use generic_handle_irq_safe()

2022-09-19T13:08:39Z

On PREEMPT_RT enabled kernels the demultiplex interrupt handler is force threaded and runs with interrupts enabled. The invocation of generic_handle_irq() with interrupts enabled triggers a lockdep warning due to a non-irq safe lock acquisition. Instead of disabling interrupts on the driver level, use generic_handle_domain_irq_safe(). [ tglx: Split out from combo patch ] Signed-off-by: Sebastian Andrzej Siewior Signed-off-by: Thomas Gleixner Link: https://lore.kernel.org/r/YnkfWFzvusFFktSt@linutronix.de

bcma: Fix typo in comments

2022-09-07T08:00:30Z

Remove the repeated word "registers" in comments. Signed-off-by: Shaomin Deng Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20220811152043.11446-1-dengshaomin@cdjrlc.com

bcma: gpio: Switch to use fwnode instead of of_node

2022-05-09T11:41:43Z

GPIO library now accepts fwnode as a firmware node, so switch the driver to use it. Signed-off-by: Andy Shevchenko Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20220504092525.71668-1-andriy.shevchenko@linux.intel.com

Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

2022-03-25T20:35:34Z

Pull MTD updates from Miquel Raynal: "There has been a lot of activity in the MTD subsystem recently, with a number of SPI-NOR cleanups as well as the introduction of ECC engines that can be used by SPI controllers (hence a few SPI patches in here). Core MTD changes: - Replace the expert mode symbols with a single helper - Fix misuses of of_match_ptr() - Remove partid and partname debugfs files - tests: Fix eraseblock read speed miscalculation for lower partition sizes - TRX parser: Allow to use on MediaTek MIPS SoCs MTD driver changes: - spear_smi: use GFP_KERNEL - mchp48l640: Add SPI ID table - mchp23k256: Add SPI ID table - blkdevs: Avoid soft lockups with some mtd/spi devices - aspeed-smc: Improve probe resilience Hyperbus changes: - HBMC_AM654 should depend on ARCH_K3 NAND core changes: - ECC: - Add infrastructure to support hardware engines - Add a new helper to retrieve the ECC context - Provide a helper to retrieve a pilelined engine device NAND-ECC changes: - Macronix ECC engine: - Add Macronix external ECC engine support - Support SPI pipelined mode - Make two read-only arrays static const - Fix compile test issue Raw NAND core changes: - Fix misuses of of_match_node() - Rework of_get_nand_bus_width() - Remove of_get_nand_on_flash_bbt() wrapper - Protect access to rawnand devices while in suspend - bindings: Document the wp-gpios property Rax NAND controller driver changes: - atmel: Fix refcount issue in atmel_nand_controller_init - nandsim: - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern - Merge repeat codes in ns_switch_state - Replace overflow check with kzalloc to single kcalloc - rockchip: Fix platform_get_irq.cocci warning - stm32_fmc2: Add NAND Write Protect support - pl353: Set the nand chip node as the flash node - brcmnand: Fix sparse warnings in bcma_nand - omap_elm: Remove redundant variable 'errors' - gpmi: - Support fast edo timings for mx28 - Validate controller clock rate - Fix controller timings setting - brcmnand: - Add BCMA shim - BCMA controller uses command shift of 0 - Allow platform data instantation - Add platform data structure for BCMA - Allow working without interrupts - Move OF operations out of brcmnand_init_cs() - Avoid pdev in brcmnand_init_cs() - Allow SoC to provide I/O operations - Assign soc as early as possible Onenand changes: - Check for error irq SPI-NAND core changes: - Delay a little bit the dirmap creation - Create direct mapping descriptors for ECC operations SPI-NAND driver changes: - macronix: Use random program load SPI NOR core changes: - Move vendor specific code out of the core into vendor drivers. - Unify all function and object names in the vendor modules. - Make setup() callback optional to improve readability. - Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash declaration. SPI changes: - Macronix SPI controller: - Fix the transmit path - Create a helper to configure the controller before an operation - Create a helper to ease the start of an operation - Add support for direct mapping - Add support for pipelined ECC operations - spi-mem: - Introduce a capability structure - Check the controller extra capabilities - cadence-quadspi/mxic: Provide capability structures - Kill the spi_mem_dtr_supports_op() helper - Add an ecc parameter to the spi_mem_op structure Binding changes: - Dropped mtd/cortina,gemini-flash.txt - Convert BCM47xx partitions to json-schema - Vendor prefixes: Clarify Macronix prefix - SPI NAND: Convert spi-nand description file to yaml - Raw NAND chip: Create a NAND chip description - Raw NAND controller: - Harmonize the property types - Fix a comment in the examples - Fix the reg property description - Describe Macronix NAND ECC engine - Macronix SPI controller: - Document the nand-ecc-engine property - Convert to yaml - The interrupt property is not mandatory" * tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits) mtd: nand: ecc: mxic: Fix compile test issue mtd: nand: mxic-ecc: make two read-only arrays static const mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3 mtd: core: Remove partid and partname debugfs files dt-bindings: mtd: partitions: convert BCM47xx to the json-schema mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init mtd: rawnand: rockchip: fix platform_get_irq.cocci warning mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set mtd: spi-nor: renumber flags mtd: spi-nor: slightly change code style in spi_nor_sr_ready() mtd: spi-nor: spansion: rename vendor specific functions and defines mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag mtd: spi-nor: move all spansion specifics into spansion.c mtd: spi-nor: spansion: slightly rework control flow in late_init() mtd: spi-nor: micron-st: rename vendor specific functions and defines mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag mtd: spi-nor: move all micron-st specifics into micron-st.c mtd: spi-nor: xilinx: correct the debug message mtd: spi-nor: xilinx: rename vendor specific functions and defines ...