linux/drivers/block/ps3disk.c, branch v2.6.32

const: make block_device_operations const

2009-09-22T14:17:25Z

Signed-off-by: Alexey Dobriyan Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

ps3: shorten ps3_system_bus_[gs]et_driver_data to ps3_system_bus_[gs]et_drvdata

2009-06-15T06:47:24Z

Signed-off-by: Geert Uytterhoeven Cc: Geoff Levand Cc: Jim Paris Acked-by: Geoff Levand Signed-off-by: Benjamin Herrenschmidt

block/ps3: remove driver_data direct access of struct device

2009-06-15T06:47:23Z

In the near future, the driver core is going to not allow direct access to the driver_data pointer in struct device. Instead, the functions dev_get_drvdata() and dev_set_drvdata() should be used. These functions have been around since the beginning, so are backwards compatible with all older kernel versions. [Geert: Use ps3_system_bus_[gs]et_driver_data() for ps3_system_bus_device] Signed-off-by: Roel Kluin Signed-off-by: Geert Uytterhoeven Cc: Jim Paris Cc: Jens Axboe Signed-off-by: Benjamin Herrenschmidt

block: Do away with the notion of hardsect_size

2009-05-22T21:22:54Z

Until now we have had a 1:1 mapping between storage device physical block size and the logical block sized used when addressing the device. With SATA 4KB drives coming out that will no longer be the case. The sector size will be 4KB but the logical block size will remain 512-bytes. Hence we need to distinguish between the physical block size and the logical ditto. This patch renames hardsect_size to logical_block_size. Signed-off-by: Martin K. Petersen Signed-off-by: Jens Axboe

block: implement and enforce request peek/start/fetch

2009-05-11T07:52:18Z

Till now block layer allowed two separate modes of request execution. A request is always acquired from the request queue via elv_next_request(). After that, drivers are free to either dequeue it or process it without dequeueing. Dequeue allows elv_next_request() to return the next request so that multiple requests can be in flight. Executing requests without dequeueing has its merits mostly in allowing drivers for simpler devices which can't do sg to deal with segments only without considering request boundary. However, the benefit this brings is dubious and declining while the cost of the API ambiguity is increasing. Segment based drivers are usually for very old or limited devices and as converting to dequeueing model isn't difficult, it doesn't justify the API overhead it puts on block layer and its more modern users. Previous patches converted all block low level drivers to dequeueing model. This patch completes the API transition by... * renaming elv_next_request() to blk_peek_request() * renaming blkdev_dequeue_request() to blk_start_request() * adding blk_fetch_request() which is combination of peek and start * disallowing completion of queued (not started) requests * applying new API to all LLDs Renamings are for consistency and to break out of tree code so that it's apparent that out of tree drivers need updating. [ Impact: block request issue API cleanup, no functional change ] Signed-off-by: Tejun Heo Cc: Rusty Russell Cc: James Bottomley Cc: Mike Miller Cc: unsik Kim Cc: Paul Clements Cc: Tim Waugh Cc: Geert Uytterhoeven Cc: David S. Miller Cc: Laurent Vivier Cc: Jeff Garzik Cc: Jeremy Fitzhardinge Cc: Grant Likely Cc: Adrian McMenamin Cc: Stephen Rothwell Cc: Bartlomiej Zolnierkiewicz Cc: Borislav Petkov Cc: Sergei Shtylyov Cc: Alex Dubov Cc: Pierre Ossman Cc: David Woodhouse Cc: Markus Lidel Cc: Stefan Weinhuber Cc: Martin Schwidefsky Cc: Pete Zaitcev Cc: FUJITA Tomonori Signed-off-by: Jens Axboe

ps3disk: dequeue in-flight request

2009-05-11T07:52:16Z

Other than in issue error paths, ps3disk always completely finishes fetched requests. With full completion on error paths, it can be easily converted to dequeueing model. * After L1 r/w call failure, ps3disk_submit_request_sg() now fails the whole request. Issue failure isn't likely to benefit from partial retry anyway and ps3disk uses full failure in completion error path too, so I don't think this amounts to any meaningful functionality loss. * flush completion is converted to _all for consistency. It doesn't make any functional difference. [ Impact: dequeue in-flight request ] Signed-off-by: Tejun Heo Cc: Geert Uytterhoeven Signed-off-by: Jens Axboe

block: convert to pos and nr_sectors accessors

2009-05-11T07:50:54Z

With recent cleanups, there is no place where low level driver directly manipulates request fields. This means that the 'hard' request fields always equal the !hard fields. Convert all rq->sectors, nr_sectors and current_nr_sectors references to accessors. While at it, drop superflous blk_rq_pos() < 0 test in swim.c. [ Impact: use pos and nr_sectors accessors ] Signed-off-by: Tejun Heo Acked-by: Geert Uytterhoeven Tested-by: Grant Likely Acked-by: Grant Likely Tested-by: Adrian McMenamin Acked-by: Adrian McMenamin Acked-by: Mike Miller Cc: James Bottomley Cc: Bartlomiej Zolnierkiewicz Cc: Borislav Petkov Cc: Sergei Shtylyov Cc: Eric Moore Cc: Alan Stern Cc: FUJITA Tomonori Cc: Pete Zaitcev Cc: Stephen Rothwell Cc: Paul Clements Cc: Tim Waugh Cc: Jeff Garzik Cc: Jeremy Fitzhardinge Cc: Alex Dubov Cc: David Woodhouse Cc: Martin Schwidefsky Cc: Dario Ballabio Cc: David S. Miller Cc: Rusty Russell Cc: unsik Kim Cc: Laurent Vivier Signed-off-by: Jens Axboe

block: implement blk_rq_pos/[cur_]sectors() and convert obvious ones

2009-05-11T07:50:53Z

Implement accessors - blk_rq_pos(), blk_rq_sectors() and blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors and rq->hard_cur_sectors respectively and convert direct references of the said fields to the accessors. This is in preparation of request data length handling cleanup. Geert : suggested adding const to struct request * parameter to accessors Sergei : spotted error in patch description [ Impact: cleanup ] Signed-off-by: Tejun Heo Acked-by: Geert Uytterhoeven Acked-by: Stephen Rothwell Tested-by: Grant Likely Acked-by: Grant Likely Ackec-by: Sergei Shtylyov Cc: Bartlomiej Zolnierkiewicz Cc: Borislav Petkov Cc: James Bottomley Signed-off-by: Jens Axboe

ps3disk: simplify request completion

2009-04-28T06:14:50Z

ps3disk_interrupt() always completes requests fully but it uses rq->hard_cur_sectors for FLUSH requests for some reason. Drop them and simply use __blk_end_request_all(). [ Impact: cleanup ] Signed-off-by: Tejun Heo Signed-off-by: Jens Axboe

block: replace end_request() with [__]blk_end_request_cur()

2009-04-28T05:37:36Z

end_request() has been kept around for backward compatibility; however, it's about time for it to go away. * There aren't too many users left. * Its use of @updtodate is pretty confusing. * In some cases, newer code ends up using mixture of end_request() and [__]blk_end_request[_all](), which is way too confusing. So, add [__]blk_end_request_cur() and replace end_request() with it. Most conversions are straightforward. Noteworthy ones are... * paride/pcd: next_request() updated to take 0/-errno instead of 1/0. * paride/pf: pf_end_request() and next_request() updated to take 0/-errno instead of 1/0. * xd: xd_readwrite() updated to return 0/-errno instead of 1/0. * mtd/mtd_blkdevs: blktrans_discard_request() updated to return 0/-errno instead of 1/0. Unnecessary local variable res initialization removed from mtd_blktrans_thread(). [ Impact: cleanup ] Signed-off-by: Tejun Heo Acked-by: Joerg Dorchain Acked-by: Geert Uytterhoeven Acked-by: Grant Likely Acked-by: Laurent Vivier Cc: Tim Waugh Cc: Stephen Rothwell Cc: Paul Mackerras Cc: Jeremy Fitzhardinge Cc: Markus Lidel Cc: David Woodhouse Cc: Pete Zaitcev Cc: unsik Kim