linux/drivers/bluetooth, branch v3.5

Bluetooth: btmrvl: Do not send vendor events to bluetooth stack

2012-06-19T03:19:11Z

Vendor-specific events shall be processed in driver and not sent to bluetooth stack where they screw up HCI command countings. Signed-off-by: Andrei Emeltchenko Signed-off-by: Gustavo Padovan

Bluetooth: add support for atheros 0930:0219

2012-06-12T02:54:33Z

Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ. usb-devices shows: T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0219 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by: Giancarlo Formicuccia Signed-off-by: Gustavo Padovan

Bluetooth: Support AR3011 in Acer Iconia Tab W500

2012-06-09T22:29:02Z

Acer used this chip connected via USB: Bus 005 Device 005: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 224 Wireless bDeviceSubClass 1 Radio Frequency bDeviceProtocol 1 Bluetooth bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x3005 AR3011 Bluetooth bcdDevice 0.01 iManufacturer 0 iProduct 0 iSerial 0 bNumConfigurations 1 Signed-off-by: Marek Vasut Cc: Gustavo Padovan Cc: Johan Hedberg Cc: Marcel Holtmann Signed-off-by: Gustavo Padovan

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2012-05-24T18:54:29Z

Pull more networking updates from David Miller: "Ok, everything from here on out will be bug fixes." 1) One final sync of wireless and bluetooth stuff from John Linville. These changes have all been in his tree for more than a week, and therefore have had the necessary -next exposure. John was just away on a trip and didn't have a change to send the pull request until a day or two ago. 2) Put back some defines in user exposed header file areas that were removed during the tokenring purge. From Stephen Hemminger and Paul Gortmaker. 3) A bug fix for UDP hash table allocation got lost in the pile due to one of those "you got it.. no I've got it.." situations. :-) From Tim Bird. 4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll try to coalesce overlapping frags and crash. Fix from Eric Dumazet. 5) RCU routing table lookups can race with free_fib_info(), causing crashes when we deref the device pointers in the route. Fix by releasing the net device in the RCU callback. From Yanmin Zhang. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits) tcp: take care of overlaps in tcp_try_coalesce() ipv4: fix the rcu race between free_fib_info and ip_route_output_slow mm: add a low limit to alloc_large_system_hash ipx: restore token ring define to include/linux/ipx.h if: restore token ring ARP type to header xen: do not disable netfront in dom0 phy/micrel: Fix ID of KSZ9021 mISDN: Add X-Tensions USB ISDN TA XC-525 gianfar:don't add FCB length to hard_header_len Bluetooth: Report proper error number in disconnection Bluetooth: Create flags for bt_sk() Bluetooth: report the right security level in getsockopt Bluetooth: Lock the L2CAP channel when sending Bluetooth: Restore locking semantics when looking up L2CAP channels Bluetooth: Fix a redundant and problematic incoming MTU check Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C Bluetooth: Fix EIR data generation for mgmt_device_found Bluetooth: Fix Inquiry with RSSI event mask Bluetooth: improve readability of l2cap_seq_list code Bluetooth: Fix skb length calculation ...

USB: Disable hub-initiated LPM for comms devices.

2012-05-18T22:42:55Z

Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp Cc: Marcel Holtmann Cc: Gustavo Padovan Cc: Johan Hedberg Cc: Hansjoerg Lipp Cc: Tilman Schmidt Cc: Karsten Keil Cc: Peter Korsgaard Cc: Jan Dumon Cc: Petko Manolov Cc: Steve Glendinning Cc: "John W. Linville" Cc: Kalle Valo Cc: "Luis R. Rodriguez" Cc: Jouni Malinen Cc: Vasanthakumar Thiagarajan Cc: Senthil Balasubramanian Cc: Christian Lamparter Cc: Brett Rudley Cc: Roland Vossen Cc: Arend van Spriel Cc: "Franky (Zhenhui) Lin" Cc: Kan Yan Cc: Dan Williams Cc: Jussi Kivilinna Cc: Ivo van Doorn Cc: Gertjan van Wingerde Cc: Helmut Schaa Cc: Herton Ronaldo Krzesinski Cc: Hin-Tak Leung Cc: Larry Finger Cc: Chaoming Li Cc: Daniel Drake Cc: Ulrich Kunitz Signed-off-by: Sarah Sharp

Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C

2012-05-16T19:13:26Z

Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to the blacklist of btusb module and add it to the ath3k module to properly load the firmware in Kernel 3.3.4 The device is integrated in e.g. some Acer Aspire 7750G. Output from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e03c Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Michael Gruetzner Signed-off-by: Gustavo Padovan

Bluetooth: btmrvl: add support for SDIO suspend/resume callbacks

2012-05-09T04:40:51Z

Host sleep is activated using already configured host sleep parameters in suspend handler and it is cancelled in resume handler. Signed-off-by: Amitkumar Karwar Signed-off-by: Bing Zhao Acked-by: Marcel Holtmann Signed-off-by: Gustavo Padovan

Bluetooth: btmrvl: configure default host sleep parameters

2012-05-09T04:40:46Z

Currently debugfs commands "hscfgcmd" and "gpiogap" are provided for host sleep configuration. But if user doesn't configure host sleep parameters using these commands, host sleep activation is failed during suspend (support for suspend and resume handlers is added in next patch). Default host sleep configuration is done during driver initialisation in this patch. Signed-off-by: Amitkumar Karwar Signed-off-by: Bing Zhao Signed-off-by: Gustavo Padovan

Bluetooth: btusb: Dynamic alternate setting

2012-05-09T04:40:35Z

The alternate setting must be dynamically set according to the number of active SCO links, and the bit depth of the audio. The possible values for the alternate setting are described in the Bluetooth Core Specification, Volume 4, Part B, section 2.1.1. Signed-off-by: Mikel Astiz Acked-by: Marcel Holtmann Signed-off-by: Gustavo Padovan

Bluetooth: btmrvl_sdio: remove pointless conditional before release_firmware()

2012-05-09T04:40:31Z

release_firmware() deals gracefullt with NULL pointers so there's no reason to test for one prior to calling the function. Signed-off-by: Jesper Juhl Signed-off-by: Gustavo Padovan