linux/drivers/bluetooth, branch v6.8

Bluetooth: qca: Fix triggering coredump implementation

2024-02-28T14:50:51Z

hci_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific command to trigger firmware coredump, but the command does not have any event as its sync response, so it is not suitable to use __hci_cmd_sync(), fixed by using __hci_cmd_send(). Fixes: 06d3fdfcdf5c ("Bluetooth: hci_qca: Add qcom devcoredump support") Signed-off-by: Zijun Hu Signed-off-by: Luiz Augusto von Dentz

Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT

2024-02-28T14:50:51Z

BT adapter going into UNCONFIGURED state during BT turn ON when devicetree has no local-bd-address node. Bluetooth will not work out of the box on such devices, to avoid this problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on local-bd-address node entry. When this quirk is not set, the public Bluetooth address read by host from controller though HCI Read BD Address command is considered as valid. Fixes: e668eb1e1578 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts") Signed-off-by: Janaki Ramaiah Thota Signed-off-by: Luiz Augusto von Dentz

Bluetooth: qca: Fix wrong event type for patch config command

2024-02-28T14:50:51Z

Vendor-specific command patch config has HCI_Command_Complete event as response, but qca_send_patch_config_cmd() wrongly expects vendor-specific event for the command, fixed by using right event type. Btmon log for the vendor-specific command are shown below: < HCI Command: Vendor (0x3f|0x0000) plen 5 28 01 00 00 00 > HCI Event: Command Complete (0x0e) plen 5 Vendor (0x3f|0x0000) ncmd 1 Status: Success (0x00) 28 Fixes: 4fac8a7ac80b ("Bluetooth: btqca: sequential validation") Signed-off-by: Zijun Hu Signed-off-by: Luiz Augusto von Dentz

Bluetooth: hci_bcm4377: do not mark valid bd_addr as invalid

2024-02-28T14:39:44Z

A recent commit restored the original (and still documented) semantics for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address is considered invalid unless an address is provided by firmware. This specifically means that this flag must only be set for devices with invalid addresses, but the Broadcom BCM4377 driver has so far been setting this flag unconditionally. Fortunately the driver already checks for invalid addresses during setup and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address is invalid but can be overridden by firmware (long term, this should probably just always be allowed). Fixes: 6945795bc81a ("Bluetooth: fix use-bdaddr-property quirk") Cc: stable@vger.kernel.org # 6.5 Reported-by: Felix Zhang Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/ Signed-off-by: Johan Hovold Reported-by: Felix Zhang Reviewed-by: Neal Gompa Signed-off-by: Luiz Augusto von Dentz

Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2024-01-18T19:43:55Z

Pull USB / Thunderbolt updates from Greg KH: "Here is the big set of USB and Thunderbolt changes for 6.8-rc1. Included in here are the following: - Thunderbolt subsystem and driver updates for USB 4 hardware and issues reported by real devices - xhci driver updates - dwc3 driver updates - uvc_video gadget driver updates - typec driver updates - gadget string functions cleaned up - other small changes All of these have been in the linux-next tree for a while with no reported issues" * tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits) usb: typec: tipd: fix use of device-specific init function usb: typec: tipd: Separate reset for TPS6598x usb: mon: Fix atomicity violation in mon_bin_vma_fault usb: gadget: uvc: Remove nested locking usb: gadget: uvc: Fix use are free during STREAMOFF usb: typec: class: fix typec_altmode_put_partner to put plugs dt-bindings: usb: dwc3: Limit num-hc-interrupters definition dt-bindings: usb: xhci: Add num-hc-interrupters definition xhci: add support to allocate several interrupters USB: core: Use device_driver directly in struct usb_driver and usb_device_driver arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue arm64: dts: qcom: msm8996: Remove PNoC clock from MSS arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI arm64: dts: qcom: msm8939: Drop RPM bus clocks arm64: dts: qcom: sdm630: Drop RPM bus clocks arm64: dts: qcom: qcs404: Drop RPM bus clocks arm64: dts: qcom: msm8996: Drop RPM bus clocks ...

Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2024-01-18T19:37:24Z

Pull tty / serial updates from Greg KH: "Here is the big set of tty and serial driver changes for 6.8-rc1. As usual, Jiri has a bunch of refactoring and cleanups for the tty core and drivers in here, along with the usual set of rs485 updates (someday this might work properly...) Along with those, in here are changes for: - sc16is7xx serial driver updates - platform driver removal api updates - amba-pl011 driver updates - tty driver binding updates - other small tty/serial driver updates and changes All of these have been in linux-next for a while with no reported issues" * tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits) serial: sc16is7xx: refactor EFR lock serial: sc16is7xx: reorder code to remove prototype declarations serial: sc16is7xx: refactor FIFO access functions to increase commonality serial: sc16is7xx: drop unneeded MODULE_ALIAS serial: sc16is7xx: replace hardcoded divisor value with BIT() macro serial: sc16is7xx: add explicit return for some switch default cases serial: sc16is7xx: add macro for max number of UART ports serial: sc16is7xx: add driver name to struct uart_driver serial: sc16is7xx: use i2c_get_match_data() serial: sc16is7xx: use spi_get_device_match_data() serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield serial: sc16is7xx: improve do/while loop in sc16is7xx_irq() serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq() serial: sc16is7xx: set safe default SPI clock frequency serial: sc16is7xx: add check for unsupported SPI modes during probe serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error serial: 8250_exar: Set missing rs485_supported flag serial: omap: do not override settings for RS485 support serial: core, imx: do not set RS485 enabled if it is not supported serial: core: make sure RS485 cannot be enabled when it is not supported ...

USB: core: Use device_driver directly in struct usb_driver and usb_device_driver

2024-01-04T15:06:32Z

There is usbdrv_wrap in struct usb_driver and usb_device_driver, it contains device_driver and for_devices. for_devices is used to distinguish between device drivers and interface drivers. Like the is_usb_device(), it tests the type of the device. We can test that if the probe of device_driver is equal to usb_probe_device in is_usb_device_driver(), and then the struct usbdrv_wrap is no longer needed. Clean up struct usbdrv_wrap, use device_driver directly in struct usb_driver and usb_device_driver. This makes the code cleaner. Signed-off-by: Yajun Deng Acked-by: Alan Stern Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev Signed-off-by: Greg Kroah-Hartman

Bluetooth: Add device 13d3:3572 IMC Networks Bluetooth Radio

2023-12-22T18:00:11Z

This 13d3:3572 is part of Realtek RTW8852BE chip. The device table is: T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3572 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Jagan Teki Signed-off-by: Luiz Augusto von Dentz

Bluetooth: btnxpuart: remove useless assignment

2023-12-22T17:58:57Z

Remove useless assignment of rx_skb to NULL in case the skb is in error, this is already done in h4_recv_buf() that is executed a few lines before. Signed-off-by: Francesco Dolcini Signed-off-by: Luiz Augusto von Dentz

Bluetooth: btmtkuart: fix recv_buf() return value

2023-12-22T17:58:35Z

Serdev recv_buf() callback is supposed to return the amount of bytes consumed, therefore an int in between 0 and count. Do not return negative number in case of issue, just print an error and return count. This fixes a WARN in ttyport_receive_buf(). Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/ Fixes: 7237c4c9ec92 ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices") Signed-off-by: Francesco Dolcini Signed-off-by: Luiz Augusto von Dentz