linux/drivers/clk/versatile, branch v4.9

clk: versatile/icst: support for AP baseboard clocks

2016-08-29T18:38:51Z

This adds support for the two ICST525-based clocks on the Integrator/AP baseboard, as documented in the board manual "Integrator/AP ASIC Development Motherboard", ARM DUI0098 B, pages 3-15 thru 3-18. Cc: Russell King Signed-off-by: Linus Walleij [sboyd@codeaurora.org: fixed uninitialized val warning] Signed-off-by: Stephen Boyd

clk: versatile/icst: add Integrator core module clocks

2016-08-25T20:03:52Z

The Integrator/AP and Integrator/CP have special derivatives of the ICST525 control registers, where some bits have been hardwired but others are possible to adjust, resulting in a control register that makes it possible to set an even, desired megahertz value. The Integrator/AP and Integrator/CP have slightly different layout so we support them using different compatible strings. After adding these clocks, the Integrator-specific cpufreq driver can be switched over to use the generic operating point device tree cpufreq driver. Instead of simply writing a value to the oscillator control register we switch to the more elaborate method of providing a bitmask and use regmap_update_bits() to poke the right bits for the desired frequency, this is needed since these control registers sometimes control more than one clock. Cc: Russell King Signed-off-by: Linus Walleij Signed-off-by: Stephen Boyd

clk: versatile: Remove CLK_IS_ROOT

2016-03-15T22:19:21Z

This flag is a no-op now. Remove usage of the flag. Cc: Pawel Moll Acked-by: Linus Walleij Signed-off-by: Stephen Boyd

clk: versatile: sp810: support reentrance

2016-02-25T23:03:28Z

Despite care take to allocate clocks state containers the SP810 driver actually just supports creating one instance: all clocks registered for every instance will end up with the exact same name and __clk_init() will fail. Rename the timclken<0> .. timclken to sp810__ so every clock on every instance gets a unique name. This is necessary for the RealView PBA8 which has two SP810 blocks: the second block will not register its clocks unless every clock on every instance is unique and results in boot logs like this: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at ../drivers/clk/versatile/clk-sp810.c:137 clk_sp810_of_setup+0x110/0x154() Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.5.0-rc2-00030-g352718fc39f6-dirty #225 Hardware name: ARM RealView Machine (Device Tree Support) [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [] (show_stack) from [] (dump_stack+0x84/0x9c) [] (dump_stack) from [] (warn_slowpath_common+0x74/0xb0) [] (warn_slowpath_common) from [] (warn_slowpath_null+0x1c/0x24) [] (warn_slowpath_null) from [] (clk_sp810_of_setup+0x110/0x154) [] (clk_sp810_of_setup) from [] (of_clk_init+0x12c/0x1c8) [] (of_clk_init) from [] (time_init+0x20/0x2c) [] (time_init) from [] (start_kernel+0x244/0x3c4) [] (start_kernel) from [<7000807c>] (0x7000807c) ---[ end trace cb88537fdc8fa200 ]--- Cc: Michael Turquette Cc: Pawel Moll Fixes: 6e973d2c4385 "clk: vexpress: Add separate SP810 driver" Signed-off-by: Linus Walleij Signed-off-by: Stephen Boyd

clk: versatile: mask VCO bits before writing

2016-02-10T17:56:31Z

The Versatile syscon ICST driver OR:s the bits into place but forgets to mask the previous value, making the code only work if the register is zero or giving haphazard results. Mask the 19 bits used by the Versatile syscon interface register. Regression caused and now fixed by yours truly. Cc: Michael Turquette Cc: Stephen Boyd Cc: linux-clk@vger.kernel.org Fixes: 179c8fb3c2a6 ("clk: versatile-icst: convert to use regmap") Signed-off-by: Linus Walleij Signed-off-by: Stephen Boyd

Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2016-01-21T02:03:56Z

Pull ARM SoC multiplatform code updates from Arnd Bergmann: "This branch is the culmination of 5 years of effort to bring the ARMv6 and ARMv7 platforms together such that they can all be enabled and boot the same kernel. It has been a tremendous amount of cleanup and refactoring by a huge number of people, and creation of several new (and major) subsystems to better abstract out all the platform details in an appropriate manner. The bulk of this branch is a large patchset from Arnd that brings several of the more minor and older platforms we have closer to multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview Much of this is moving around header files from old mach directories, but there are also some cleanup patches of debug_ll (lowlevel debug per-platform options) and other parts. Linus Walleij also has some patchs to clean up the older ARM Realview platforms by finally introducing DT support, and Rob Herring has some for ARM Versatile which is now DT-only. Both of these platforms are now multiplatform. Finally, a couple of patches from Russell for Dove PMU, and a fix from Valentin Rothberg for Exynos ADC, which were rebased on top of the series to avoid conflicts" * tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits) ARM: realview: don't select SMP_ON_UP for UP builds ARM: s3c: simplify s3c_irqwake_{e,}intallow definition ARM: s3c64xx: fix pm-debug compilation iio: exynos-adc: fix irqf_oneshot.cocci warnings ARM: realview: build realview-dt SMP support only when used ARM: realview: select apropriate targets ARM: realview: clean up header files ARM: realview: make all header files local ARM: no longer make CPU targets visible separately ARM: integrator: use explicit core module options ARM: realview: enable multiplatform ARM: make default platform work for NOMMU ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location ARM: defconfig: use correct debug_ll settings ARM: versatile: convert to multi-platform ARM: versatile: merge mach code into a single file ARM: versatile: switch to DT only booting and remove legacy code ARM: versatile: add DT based PCI detection ARM: pxa: mark ezx structures as __maybe_unused ARM: pxa: mark raumfeld init functions as __maybe_unused ...

Merge tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/multiplatform

2015-12-15T23:56:18Z

Merge "Realview multiplatform support" from Linus Walleij: The board and infrastructure changes for RealView multiplatform and extended DT support. * tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator: ARM: realview: add an DT SMP boot method ARM: realview: select SP810 and ICST for the DT variant soc: versatile: add support for the PB11MPCore clk: versatile-icst: add device tree support clk: versatile-icst: refactor to allocate regmap separately clk: versatile-icst: convert to use regmap ARM: realview: remove private barrier implementation ARM: no longer force unbuffered DMA for realview clk/realview: stop using machine headers ARM: realview: don't map undefined PCI registers ARM: realview: remove sparsemem hack Conflicts: drivers/clk/versatile/Kconfig

ARM: versatile: switch to DT only booting and remove legacy code

2015-12-15T22:53:21Z

With DT support for clocks, irqchips, timers, and PCI now in place, DT based booting has feature parity with non-DT legacy boot. The final piece is actually enabling common clock support on Versatile. Enabling full DT support requires either removing the old Versatile clock code, updating the legacy boot to use the common clock code, or making DT and legacy boot mutually exclusive. Given that removing legacy boot code is the goal anyway, I am going with the 1st option. Signed-off-by: Rob Herring Cc: Russell King Cc: Linus Walleij Cc: Mike Turquette Signed-off-by: Arnd Bergmann

clk: versatile-icst: add device tree support

2015-12-15T08:42:50Z

This adds support for the ARM syscon ICST clocks to initialized directly from the device tree syscon node on ARM Integrator, Versatile and RealView reference designs. Cc: Michael Turquette Cc: Stephen Boyd Cc: linux-clk@vger.kernel.org Signed-off-by: Linus Walleij

clk: versatile-icst: refactor to allocate regmap separately

2015-12-15T08:42:49Z

Break out the registration function so it creates a regmap and pass to the setup function, so the latter can be shared with a device tree probe function that already has a regmap. Cc: Michael Turquette Cc: Stephen Boyd Cc: linux-clk@vger.kernel.org Signed-off-by: Linus Walleij