linux/drivers/gpio, branch v3.12

gpiolib: let gpiod_request() return -EPROBE_DEFER

2013-10-11T14:31:54Z

Patch be1a4b brought some improvements to the GPIO error handling code, but also changed the return value of gpiod_request() when called on a not yet initialized GPIO descriptor: it now returns -EINVAL instead of -EPROBE_DEFER, and this affects some drivers. This patch restores the original behavior for gpiod_request(). It is safe to do so now that desc_to_gpio() does not rely on the GPIO descriptor to be initialized. Other functions changed by patch be1a4b do not see their return value affected, so these are not reverted. Signed-off-by: Alexandre Courbot Reported-by: Dr. H. Nikolaus Schaller Signed-off-by: Linus Walleij

gpiolib: safer implementation of desc_to_gpio()

2013-10-11T14:31:53Z

The current implementation of desc_to_gpio() relies on the chip pointer to be set to a valid value in order to compute the GPIO number. This was done in the hope that we can get rid of the gpio_desc global array, but this is not happening anytime soon. This patch reimplements desc_to_gpio() in a fashion similar to that of gpio_to_desc(). As a result, desc_to_gpio(gpio_to_desc(gpio)) == gpio is now always true. This allows to call desc_to_gpio() on non-initialized descriptors as some error-handling code currently does. Signed-off-by: Alexandre Courbot Reported-by: Dr. H. Nikolaus Schaller Signed-off-by: Linus Walleij

gpio/lynxpoint: check if the interrupt is enabled in IRQ handler

2013-10-11T11:16:32Z

Checking LP_INT_STAT is not enough in the interrupt handler because its contents get updated regardless of whether the pin has interrupt enabled or not. This causes the driver to loop forever for GPIOs that are pulled up. Fix this by checking the interrupt enable bit for the pin as well. Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg Acked-by: Mathias Nyman Signed-off-by: Linus Walleij

Merge tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

2013-10-05T19:11:40Z

Pull GPIO fixes from Linus Walleij: "Two patches for the OMAP driver, dealing with setting up IRQs properly on the device tree boot path" * tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio/omap: auto-setup a GPIO when used as an IRQ gpio/omap: maintain GPIO and IRQ usage separately

gpio/omap: auto-setup a GPIO when used as an IRQ

2013-10-01T11:16:02Z

The OMAP GPIO controller HW requires a pin to be configured in GPIO input mode in order to operate as an interrupt input. Since drivers should not be aware of whether an interrupt pin is also a GPIO or not, the HW should be fully configured/enabled as an IRQ if a driver solely uses IRQ APIs such as request_irq(), and never calls any GPIO-related APIs. As such, add the missing HW setup to the OMAP GPIO controller's irq_chip driver. Since this bypasses the GPIO subsystem we have to ensure that another driver won't be able to request the same GPIO pin that is used as an IRQ and set its direction as output. Requesting the GPIO and setting its direction as input is allowed though. This fixes smsc911x ethernet support for tobi and igep OMAP3 boards and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line. Cc: stable@vger.kernel.org Acked-by: Stephen Warren Tested-by: George Cherian Tested-by: Aaro Koskinen Tested-by: Lars Poeschel Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Acked-by: Santosh Shilimkar Acked-by: Tony Lindgren Signed-off-by: Javier Martinez Canillas Signed-off-by: Linus Walleij

gpio/omap: maintain GPIO and IRQ usage separately

2013-10-01T11:15:07Z

The GPIO OMAP controller pins can be used as IRQ and GPIO independently so is necessary to keep track GPIO pins and IRQ lines usage separately to make sure that the bank will always be enabled while being used. Also move gpio_is_input() definition in preparation for the next patch that setups the controller's irq_chip driver when a caller requests an interrupt line. Cc: stable@vger.kernel.org Acked-by: Stephen Warren Tested-by: George Cherian Tested-by: Aaro Koskinen Tested-by: Lars Poeschel Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Acked-by: Santosh Shilimkar Acked-by: Tony Lindgren Signed-off-by: Javier Martinez Canillas Signed-off-by: Linus Walleij

gpio: rcar: Remove #gpio-range-cells DT property usage

2013-09-22T12:28:11Z

Commit a1bc260bb5f5d95da854be7898202d788e94448d ("gpio: clean up gpio-ranges documentation") deprecated the #gpio-range-cells property. Replace its usage with a hardcoded value in the gpio-rcar driver. Signed-off-by: Laurent Pinchart Acked-by: Linus Walleij Signed-off-by: Simon Horman

Remove GENERIC_HARDIRQ config option

2013-09-13T13:09:52Z

After the last architecture switched to generic hard irqs the config options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code for !CONFIG_GENERIC_HARDIRQS can be removed. Signed-off-by: Martin Schwidefsky

Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus

2013-09-12T23:14:49Z

Pull MIPS updates from Ralf Baechle: "This has been sitting in -next for a while with no objections and all MIPS defconfigs except one are building fine; that one platform got broken by another patch in your tree and I'm going to submit a patch separately. - a handful of fixes that didn't make 3.11 - a few bits of Octeon 3 support with more to come for a later release - platform enhancements for Octeon, ath79, Lantiq, Netlogic and Ralink SOCs - a GPIO driver for the Octeon - some dusting off of the DECstation code - the usual dose of cleanups" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits) MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code MIPS: kexec: Fix random crashes while loading crashkernel MIPS: kdump: Skip walking indirection page for crashkernels MIPS: DECstation HRT calibration bug fixes MIPS: Export copy_from_user_page() (needed by lustre) MIPS: Add driver for the built-in PCI controller of the RT3883 SoC MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000 MIPS: ralink: Add support for reset-controller API MIPS: ralink: mt7620: Add cpu-feature-override header MIPS: ralink: mt7620: Add spi clock definition MIPS: ralink: mt7620: Add wdt clock definition MIPS: ralink: mt7620: Improve clock frequency detection MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts MIPS: ralink: mt7620: Add verbose ram info MIPS: ralink: Probe clocksources from OF MIPS: ralink: Add support for systick timer found on newer ralink SoC MIPS: ralink: Add support for periodic timer irq MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards MIPS: Netlogic: Add support for USB on XLP2xx MIPS: Netlogic: XLP2xx update for I2C controller ...

Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux

2013-09-10T20:53:52Z

Pull device tree core updates from Grant Likely: "Generally minor changes. A bunch of bug fixes, particularly for initialization and some refactoring. Most notable change if feeding the entire flattened tree into the random pool at boot. May not be significant, but shouldn't hurt either" Tim Bird questions whether the boot time cost of the random feeding may be noticeable. And "add_device_randomness()" is definitely not some speed deamon of a function. * tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: of/platform: add error reporting to of_amba_device_create() irq/of: Fix comment typo for irq_of_parse_and_map of: Feed entire flattened device tree into the random pool of/fdt: Clean up casting in unflattening path of/fdt: Remove duplicate memory clearing on FDT unflattening gpio: implement gpio-ranges binding document fix of: call __of_parse_phandle_with_args from of_parse_phandle of: introduce of_parse_phandle_with_fixed_args of: move of_parse_phandle() of: move documentation of of_parse_phandle_with_args of: Fix missing memory initialization on FDT unflattening of: consolidate definition of early_init_dt_alloc_memory_arch() of: Make of_get_phy_mode() return int i.s.o. const int include: dt-binding: input: create a DT header defining key codes. of/platform: Staticize of_platform_device_create_pdata() of: Specify initrd location using 64-bit dt: Typo fix OF: make of_property_for_each_{u32|string}() use parameters if OF is not enabled