linux/drivers/gpu/drm/amd/display, branch v5.0

drm/amd/display: Use vrr friendly pageflip throttling in DC.

2019-02-27T18:55:09Z

In VRR mode, keep track of the vblank count of the last completed pageflip in amdgpu_crtc->last_flip_vblank, as recorded in the pageflip completion handler after each completed flip. Use that count to prevent mmio programming a new pageflip within the same vblank in which the last pageflip completed, iow. to throttle pageflips to at most one flip per video frame, while at the same time allowing to request a flip not only before start of vblank, but also anywhere within vblank. The old logic did the same, and made sense for regular fixed refresh rate flipping, but in vrr mode it prevents requesting a flip anywhere inside the possibly huge vblank, thereby reducing framerate in vrr mode instead of improving it, by delaying a slightly delayed flip requests up to a maximum vblank duration + 1 scanout duration. This would limit VRR usefulness to only help applications with a very high GPU demand, which can submit the flip request before start of vblank, but then have to wait long for fences to complete. With this method a flip can be both requested and - after fences have completed - executed, ie. it doesn't matter if the request (amdgpu_dm_do_flip()) gets delayed until deep into the extended vblank due to cpu execution delays. This also allows clients which want to regulate framerate within the vrr range a much more fine-grained control of flip timing, a feature that might be useful for video playback, and is very useful for neuroscience/vision research applications. In regular non-VRR mode, retain the old flip submission behavior. This to keep flip scheduling for fullscreen X11/GLX OpenGL clients intact, if they use the GLX_OML_sync_control extensions glXSwapBufferMscOML(, ..., target_msc,...) function with a specific target_msc target vblank count. glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will not flip at the proper target_msc for a non-zero target_msc if VRR mode is active with this patch. They'd often flip one frame too early. However, this limitation should not matter much in VRR mode, as scheduling based on vblank counts is pretty futile/unusable under variable refresh duration anyway, so no real extra harm is done. Signed-off-by: Mario Kleiner Cc: Nicholas Kazlauskas Cc: Harry Wentland Cc: Alex Deucher Cc: Michel Dänzer Signed-off-by: Alex Deucher

drm/amd/display: set clocks to 0 on suspend on dce80

2019-02-20T21:58:06Z

[Why] When a dce80 asic was suspended, the clocks were not set to 0. Upon resume, the new clock was compared to the existing clock, they were found to be the same, and so the clock was not set. This resulted in a blackscreen. [How] In atomic commit, check to see if there are any active pipes. If no, set clocks to 0 Signed-off-by: Bhawanpreet Lakha Reviewed-by: Nicholas Kazlauskas Acked-by: Leo Li Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org

drm/amd/display: fix optimize_bandwidth func pointer for dce80

2019-02-20T21:57:47Z

[Why] optimize_bandwidth was using dce100_prepare_bandwidth this is incorrect [How] change it to dce100_optimize_bandwidth Signed-off-by: Bhawanpreet Lakha Reviewed-by: Charlene Liu Acked-by: Leo Li Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org

drm/amd/display: Fix negative cursor pos programming

2019-02-20T21:56:28Z

[Why] If the cursor pos passed from DM is less than the plane_state->dst_rect top left corner then the unsigned cursor pos wraps around to a large positive number since cursor pos is a u32. There was an attempt to guard against this in hubp1_cursor_set_position by checking the src_x_offset and src_y_offset and offseting the cursor hotspot within hubp1_cursor_set_position. However, the cursor position itself is still being programmed incorrectly as a large value. This manifests itself visually as the cursor disappearing or containing strange artifacts near the middle of the screen on raven. [How] Don't subtract the destination rect top left corner from the pos but add it to the hotspot instead. This happens before the pos gets passed into hubp1_cursor_set_position. This achieves the same result but avoids the subtraction wrap around. With this fix the original cursor programming logic can be used again. Signed-off-by: Nicholas Kazlauskas Reviewed-by: Charlene Liu Acked-by: Leo Li Acked-by: Murton Liu Signed-off-by: Alex Deucher

drm/amd/display: Raise dispclk value for dce11

2019-02-19T20:33:47Z

[Why] The visual corruption due to low display clock value. Observed on Carrizo 4K@60Hz. [How] There was earlier patch for dce_update_clocks: Adding +15% workaround also to to dce11_update_clocks Signed-off-by: Roman Li Reviewed-by: Nicholas Kazlauskas Acked-by: Leo Li Signed-off-by: Alex Deucher

drm/amd/display: Fix MST reboot/poweroff sequence

2019-02-19T20:33:47Z

[Why] drm_dp_mst_topology_mgr_suspend() is added into the new reboot sequence, which disables the UP request at the beginning. Therefore sideband messages are blocked. [How] Finish MST sideband message transaction before UP request is suppressed. Signed-off-by: Leo (Hanghong) Ma Reviewed-by: Roman Li Acked-by: Leo Li Signed-off-by: Alex Deucher Cc: stable@vger.kernel.org

drm/amd/display: Expose connector VRR range via debugfs

2019-02-08T19:12:25Z

[Why] It's useful to know the min and max vrr range for IGT testing. [How] Expose the min and max vfreq for the connector via a debugfs file on the connector, "vrr_range". Example usage: cat /sys/kernel/debug/dri/0/DP-1/vrr_range Signed-off-by: Nicholas Kazlauskas Reviewed-by: Harry Wentland Signed-off-by: Alex Deucher

drm/amd/display: Attach VRR properties for eDP connectors

2019-02-05T23:10:28Z

[Why] eDP was missing in the checks for supported VRR connectors. [How] Attach the properties for eDP connectors too. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202449 Signed-off-by: Nicholas Kazlauskas Reviewed-by: Alex Deucher Signed-off-by: Alex Deucher

drm/amd/display: Fix fclk idle state

2019-02-01T05:11:32Z

[Why] The earlier change 'Fix 6x4K displays' led to fclk value idling at higher DPM level. [How] Apply the fix only to respective multi-display configuration. Signed-off-by: Roman Li Reviewed-by: Feifei Xu Acked-by: Alex Deucher Signed-off-by: Alex Deucher

drm/amd/display: Detach backlight from stream

2019-01-16T22:11:47Z

[Why] Backlight is conceptually a property of links, not streams. All backlight programming is done on links, but there is a stream property bl_pwm_level that is used to restore backlight on dpms on and s3 resume. This is unnecessary, as backlight is already restored by hardware with no driver intervention. [How] Remove bl_pwm_level, and the stream argument to set_backlight Bug: https://bugs.freedesktop.org/show_bug.cgi?id=109375 Signed-off-by: David Francis Reviewed-by: Harry Wentland Acked-by: Anthony Koo Acked-by: Leo Li Signed-off-by: Alex Deucher (cherry picked from commit 923fe4951282cbdfce05186c10380bbc45b5e03b)