linux/drivers/input/misc, branch v2.6.30

Input: hp_sdc_rtc should depend on serio

2009-04-15T15:58:19Z

Fix this build error when CONFIG_SERIO is not set hp_sdc_rtc.c:691: undefined reference to `hp_sdc_request_timer_irq' and so on.. "select should be used with care. select will force a symbol to a value without visiting the dependencies." Signed-off-by: Alexander Beregalov Signed-off-by: Dmitry Torokhov

Input: arrange drivers/input/misc/Makefile in alphabetical order

2009-03-10T03:15:42Z

Everyone adds their driver to the end of the list, hopefully if it is in alphabetical order new drivers will spread out a bit and I can merge them more easily. Signed-off-by: Dmitry Torokhov

Input: add driver for S1 button of rb532

2009-03-10T03:10:12Z

Mikrotik's Routerboard 532 has two builtin buttons, from which one triggers a hardware reset. The other one is accessible through GPIO pin 1. Sadly, this pin is being multiplexed with UART0 input, so enabling it as interrupt source (as implied by the gpio-keys driver) is not possible unless UART0 has been turned off. The later one though is a rather bad idea as the Routerboard is an embedded device with only a single serial port, so it's almost always used as serial console device. This patch adds a driver based on INPUT_POLLDEV, which disables the UART and reconfigures GPIO pin 1 temporarily while reading the button state. This procedure works fine and has been tested as part of another, unpublished driver for this device. Signed-off-by: Phil Sutter Signed-off-by: Dmitry Torokhov

Input: generic driver for rotary encoders on GPIOs

2009-03-08T23:35:53Z

This patch adds a generic driver for rotary encoders connected to GPIO pins of a system. It relies on gpiolib and generic hardware irqs. The documentation that also comes with this patch explains the concept and how to use the driver. Signed-off-by: Daniel Mack Tested-by: H Hartley Sweeten Signed-off-by: Dmitry Torokhov

Merge commit 'v2.6.29-rc7' into next

2009-03-08T23:30:55Z

Input: ati_remote2 - check module params

2009-01-30T07:43:42Z

Validate that the values of the module parameters are within the supported range. Also print the values in hex since that seems like a better match for bitmasks than decimal. Signed-off-by: Ville Syrjala Signed-off-by: Dmitry Torokhov

Input: ati_remote2 - add per device attrs

2009-01-30T07:43:35Z

Add per device channel_mask and mode_mask attributes. They inherit the values from the module parameters when the device is registered. One additional benefit is that now runtime changes to channel_mask can actually affect the hardware channel setup like they should. Signed-off-by: Ville Syrjala Signed-off-by: Dmitry Torokhov

Input: ati_remote2 - complete suspend support

2009-01-30T07:43:29Z

Add the missing reset_resume, pre_reset and post_reset hooks. Signed-off-by: Ville Syrjala Signed-off-by: Dmitry Torokhov

input: PCF50633 input driver

2009-01-11T00:34:25Z

Signed-off-by: Balaji Rao Cc: Andy Green Cc: Dmitry Torokhov Acked-by: Dmitry Torokhov Signed-off-by: Samuel Ortiz

Input: apanel - convert to new i2c binding

2009-01-07T13:29:17Z

Convert the apanel driver to the new i2c device driver binding model, as the legacy model is going away soon. In the new model, the apanel driver is no longer scanning all the i2c adapters, instead the relevant bus driver (i2c-i801) is instantiating the device as needed. One side benefit is that the apanel driver will now load automatically on all systems where it is needed. Signed-off-by: Jean Delvare Cc: Stephen Hemminger