linux/drivers/input/mouse/psmouse-base.c, branch v4.7

Input: byd - enable absolute mode

2016-03-18T00:04:54Z

The Windows driver's settings dialog contains a visualization of the regions for the hardware edge scrolling capability, which uses a temporarily-enabled limited-resolution absolute mode. This patch enables this during normal operation, and combines the absolute packets with the existing relative packets to provide accurate absolute position and touch reporting. It also adds documentation for all known gesture packets and initialization commands. Reviewed-by: Chris Diamand Signed-off-by: Richard Pospesel Signed-off-by: Dmitry Torokhov

Input: byd - add BYD PS/2 touchpad driver

2016-01-28T01:27:25Z

Driver for the BYD BTP10463 touchpad, found in PC Specialist `Lafite' laptops. This patch sends the magic command sequence which causes the touchpad to stream intellimouse-style packets. Gestures are detected inside the touchpad, and exposed as special values in the Z component of each packet - absolute coordinates are not supported, even in the Windows driver. At present, this supports two-finger vertical and horizontal scrolling, and provides the framework to expose the other gestures it can recognize. Signed-off-by: Chris Diamand Signed-off-by: Dmitry Torokhov

Input: psmouse - rename ps2pp_init() to ps2pp_detect()

2015-12-17T23:24:37Z

This makes Logitech PS2++ protocol implementation consistent with the naming in other protocols. Also mark the stub as "static inline" Reviewed-by: Hans de Goede Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov

Input: psmouse - limit protocols that we try on passthrough ports

2015-12-17T23:24:32Z

PS/2 protocol is slow, and using it with pass-through port (where we encapsulate PS/2 into PS/2) is slower yet so it takes quite a bit of time to do full protocol discovery for device attached to a pass-through port. However, so far we have not see anything but trackpoints or basic PS/2 mice on pass-through ports, so let's limit protocols that we probe there to Trackpoint, IntelliMouse Explorer, IntelliMouse, and bare PS/2 protocol, and avoid other extended protocols, such as Synaptics, ALPS, etc. Reviewed-by: Hans de Goede Reviewed-by: Pali Rohár Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov

Input: psmouse - factor out common protocol probing code

2015-12-17T23:24:21Z

In preparation of limiting protocols that we try on pass-through ports, let's rework initialization code and factor common code into psmouse_try_protocol() that accepts protocol type (instead of detec() function pointer) and can, for most protocols, perform both detection and initialization. Note that this removes option of forcing Lifebook protocol on devices that are not recognized by lifebook_detect() as having the hardware, but I do not recall anyone using this option. Reviewed-by: Hans de Goede Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov

Input: psmouse - move protocol descriptions around

2015-12-17T23:24:16Z

We move protocol descriptions and psmouse_find_by_type() and pmouse_find_by_name() so that we can use them without forward declarations in the subsequent patches. Reviewed-by: Hans de Goede Reviewed-by: Pali Rohár Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov

Input: psmouse - clean up Cypress probe

2015-12-17T23:24:04Z

When Cypress protocol support is disabled cypress_init() is a stub that always returns -ENOSYS, so there is not point in testing for CONFIG_MOUSE_PS2_CYPRESS after we decided that we are dealing with a Cypress device. Also, we should only be calling cypress_detect() when set_properties argument is "true", like with other protocols. There is a slight change in behavior to make follow-up patches more uniform: when we detect Cypress but its initialization fails, instead of immediately returning PSMOUSE_PS2 protocol we now continue trying IntelliMouse [Explorer]. Given that Cypress devices only have issue with Sentelic probes probing Imtellimouse should be safe. Reviewed-by: Hans de Goede Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov

Input: psmouse - rearrange Focaltech init code

2015-12-17T23:23:54Z

The fact that we were calling focaltech_init() even when Focaltech support is disabled was confusing. Rearrange the code so that if support is disabled we continue to fall through the rest of protocol probing code until we get to full reset that Focaltech devices need to work properly. Also, replace focaltech_init() with a stub now that it is only called when protocol is enabled. Reviewed-by: Hans de Goede Reviewed-by: Pali Rohár Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov

Input: psmouse - fix comment style

2015-12-17T23:23:43Z

The module was using non-standard comment style with comment blocks often starting at the very beginning of a line instead of being aligned with the code. Let's switch to standard formatting. Reviewed-by: Hans de Goede Reviewed-by: Pali Rohár Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov

Input: psmouse - use switch statement in psmouse_process_byte()

2015-12-17T23:23:34Z

Instead of a series mostly exclusive "if" statements testing protocol type of the mouse let's use "switch" statement. Reviewed-by: Hans de Goede Reviewed-by: Pali Rohár Tested-by: Marcin Sochacki Tested-by: Till Signed-off-by: Dmitry Torokhov