linux/drivers/input/touchscreen, branch v6.7

Merge branch 'next' into for-linus

2023-11-06T23:42:08Z

Prepare input updates for 6.7 merge window.

Input: cyttsp5 - add handling for vddio regulator

2023-10-27T23:20:38Z

The Cypress touchscreen controllers are often used with external pull-up for the interrupt line and the I2C lines, so we might need to enable a regulator to bring the lines into usable state. Otherwise, this might cause spurious interrupts and reading from I2C will fail. Implement support for a "vddio-supply" that is enabled by the cyttsp5 driver so that the regulator gets enabled when needed. Signed-off-by: Lin, Meng-Bo Acked-by: Alistair Francis Link: https://lore.kernel.org/r/20221117190507.87535-3-linmengbo0689@protonmail.com Signed-off-by: Dmitry Torokhov

Input: goodix - ensure int GPIO is in input for gpio_count == 1 && gpio_int_idx == 0 case

2023-10-04T14:21:45Z

Add a special case for gpio_count == 1 && gpio_int_idx == 0 to goodix_add_acpi_gpio_mappings(). It seems that on newer x86/ACPI devices the reset and irq GPIOs are no longer listed as GPIO resources instead there is only 1 GpioInt resource and _PS0 does the whole reset sequence for us. This means that we must call acpi_device_fix_up_power() on these devices to ensure that the chip is reset before we try to use it. This part was already fixed in commit 3de93e6ed2df ("Input: goodix - call acpi_device_fix_up_power() in some cases") by adding a call to acpi_device_fix_up_power() to the generic "Unexpected ACPI resources" catch all. But it turns out that this case on some hw needs some more special handling. Specifically the firmware may bootup with the IRQ pin in output mode. The reset sequence from ACPI _PS0 (executed by acpi_device_fix_up_power()) should put the pin in input mode, but the GPIO subsystem has cached the direction at bootup, causing request_irq() to fail due to gpiochip_lock_as_irq() failure: [ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0 [ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060 [ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8 [ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ [ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ [ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio [ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5 Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0 which adds an ACPI GPIO lookup table for the int GPIO even though we cannot use it for reset purposes (as there is no reset GPIO). Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call succeed, which will explicitly set the direction to input fixing the issue. Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since there is only 1 GPIO in the ACPI resources the reset entry in that lookup table will amount to a no-op. Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com> Signed-off-by: Hans de Goede Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov

Input: wm97xx-core - convert to platform remove callback returning void

2023-09-24T02:28:17Z

The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König Acked-by: Charles Keepax Link: https://lore.kernel.org/r/20230920125829.1478827-53-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov

Input: wm831x-ts - convert to platform remove callback returning void

2023-09-24T02:28:17Z

The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König Acked-by: Charles Keepax Link: https://lore.kernel.org/r/20230920125829.1478827-52-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov

Input: ti_am335x_tsc - convert to platform remove callback returning void

2023-09-24T02:28:16Z

The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20230920125829.1478827-51-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov

Input: sun4i-ts - convert to platform remove callback returning void

2023-09-24T02:28:16Z

The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20230920125829.1478827-50-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov

Input: stmpe-ts - convert to platform remove callback returning void

2023-09-24T02:28:16Z

The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20230920125829.1478827-49-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov

Input: pcap_ts - convert to platform remove callback returning void

2023-09-24T02:28:16Z

The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20230920125829.1478827-48-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov

Input: mc13783_ts - convert to platform remove callback returning void

2023-09-24T02:28:15Z

The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20230920125829.1478827-47-u.kleine-koenig@pengutronix.de Signed-off-by: Dmitry Torokhov