linux/drivers/mmc/core/debugfs.c, branch v4.5

mmc: debugfs: correct wrong voltage value

2016-01-19T09:14:22Z

Correct the wrong voltage value shown in debugfs for mmc/sd/sdio. Signed-off-by: Chuanxiao Dong Signed-off-by: Pawel Wodkowski Fixes: 42cd95a0603e ("mmc: core: debugfs: Add signal_voltage to ios dump") Signed-off-by: Ulf Hansson

mmc: core: Remove MMC_CLKGATE

2015-10-26T15:00:09Z

MMC_CLKGATE was once invented to save power by gating the bus clock at request inactivity. At that time it served its purpose. The modern way to deal with power saving for these scenarios, is by using runtime PM. Nowadays, several host drivers have deployed runtime PM, but for those that haven't and which still cares power saving at request inactivity, it's certainly time to deploy runtime PM as it has been around for several years now. To simplify code to mmc core and thus decrease maintenance efforts, this patch removes all code related to MMC_CLKGATE. Signed-off-by: Ulf Hansson Reviewed-by: Linus Walleij

mmc: debugfs: implement ios show for SDR12 and SDR25

2015-10-26T15:00:02Z

This patch add MMC_TIMING_UHS_SDR12 and MMC_TIMING_UHS_SDR25 for mmc_ios_show to show the ios->timing if mmc card runs under these two modes. Signed-off-by: Shawn Lin Signed-off-by: Ulf Hansson

mmc: debugfs: implement ios show for driver type

2015-10-26T14:59:58Z

This patch add ios->drv_type for mmc_ios_show to show the card's driver type. Signed-off-by: Shawn Lin Signed-off-by: Ulf Hansson

mmc: core: Use mmc_get_ext_csd() instead of mmc_send_ext_csd()

2014-11-10T11:40:44Z

By using mmc_get_ext_csd() in favor of mmc_send_ext_csd, we decrease code duplication. Signed-off-by: Ulf Hansson

mmc: add support for HS400 mode of eMMC5.0

2014-05-12T22:06:06Z

This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high speed DDR interface timing from HS200. Clock frequency is up to 200MHz and only 8-bit bus width is supported. In addition, tuning process of HS200 is required to synchronize the command response on the CMD line because CMD input timing for HS400 mode is the same as HS200 mode. Signed-off-by: Seungwon Jeon Reviewed-by: Jackey Shen Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: rework selection of bus speed mode

2014-05-12T22:06:04Z

Current implementation for bus speed mode selection is too complicated. This patch is to simplify the codes and remove some duplicate parts. The following changes are including: * Adds functions for each mode selection(HS, HS-DDR, HS200 and etc) * Rearranged the mode selection sequence with supported device type * Adds maximum speed for HS200 mode(hs200_max_dtr) * Adds field definition for HS_TIMING of EXT_CSD Signed-off-by: Seungwon Jeon Tested-by: Jaehoon Chung Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: clarify DDR timing mode between SD-UHS and eMMC

2014-04-20T20:59:28Z

This change distinguishes DDR timing mode of current mixed usage to clarify device type. Signed-off-by: Seungwon Jeon Acked-by: Jaehoon Chung Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: block: Enable runtime pm for mmc blkdevice

2013-05-26T18:23:16Z

Once the mmc blkdevice is being probed, runtime pm will be enabled. By using runtime autosuspend, the power save operations can be done when request inactivity occurs for a certain time. Right now the selected timeout value is set to 3 s. Obviously this value will likely need to be configurable somehow since it needs to be trimmed depending on the power save algorithm. For SD-combo cards, we are still leaving the enablement of runtime PM to the SDIO init sequence since it depends on the capabilities of the SDIO func driver. Moreover, when the blk device is being suspended, we make sure the device will be runtime resumed. The reason for doing this is that we want the host suspend sequence to be unaware of any runtime power save operations done for the card in this phase. Thus it can just handle the suspend as the card is fully powered from a runtime perspective. Finally, this patch prepares to make it possible to move BKOPS handling into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be accomplished. Signed-off-by: Ulf Hansson Signed-off-by: Chris Ball

mmc: core: debugfs: Add signal_voltage to ios dump

2012-12-06T18:54:36Z

Signed-off-by: Johan Rudholm Reviewed-by: Philip Rakity Signed-off-by: Chris Ball