linux/drivers/mmc, branch v5.17

mmc: core: Restore (almost) the busy polling for MMC_SEND_OP_COND

2022-03-07T10:47:39Z

Commit 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1"), significantly decreased the polling period from ~10-12ms into just a couple of us. The purpose was to decrease the total time spent in the busy polling loop, but unfortunate it has lead to problems, that causes eMMC cards to never gets out busy and thus fails to be initialized. To fix the problem, but also to try to keep some of the new improved behaviour, let's start by using a polling period of 1-2ms, which then increases for each loop, according to common polling loop in __mmc_poll_for_busy(). Reported-by: Jean Rene Dawin Reported-by: H. Nikolaus Schaller Cc: Huijin Park Fixes: 76bfc7ccc2fa ("mmc: core: adjust polling interval for CMD1") Signed-off-by: Ulf Hansson Tested-by: Jean Rene Dawin Tested-by: H. Nikolaus Schaller Link: https://lore.kernel.org/r/20220304105656.149281-1-ulf.hansson@linaro.org

mmc: meson: Fix usage of meson_mmc_post_req()

2022-02-28T12:18:12Z

Currently meson_mmc_post_req() is called in meson_mmc_request() right after meson_mmc_start_cmd(). This could lead to DMA unmapping before the request is actually finished. To fix, don't call meson_mmc_post_req() until meson_mmc_request_done(). Signed-off-by: Rong Chen Reviewed-by: Kevin Hilman Fixes: 79ed05e329c3 ("mmc: meson-gx: add support for descriptor chain mode") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220216124239.4007667-1-rong.chen@amlogic.com Signed-off-by: Ulf Hansson

mmc: block: fix read single on recovery logic

2022-02-08T15:04:49Z

On reads with MMC_READ_MULTIPLE_BLOCK that fail, the recovery handler will use MMC_READ_SINGLE_BLOCK for each of the blocks, up to MMC_READ_SINGLE_RETRIES times each. The logic for this is fixed to never report unsuccessful reads as success to the block layer. On command error with retries remaining, blk_update_request was called with whatever value error was set last to. In case it was last set to BLK_STS_OK (default), the read will be reported as success, even though there was no data read from the device. This could happen on a CRC mismatch for the response, a card rejecting the command (e.g. again due to a CRC mismatch). In case it was last set to BLK_STS_IOERR, the error is reported correctly, but no retries will be attempted. Fixes: 81196976ed946c ("mmc: block: Add blk-mq support") Cc: stable@vger.kernel.org Signed-off-by: Christian Loehle Reviewed-by: Adrian Hunter Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com Signed-off-by: Ulf Hansson

moxart: fix potential use-after-free on remove path

2022-01-31T14:36:34Z

It was reported that the mmc host structure could be accessed after it was freed in moxart_remove(), so fix this by saving the base register of the device and using it instead of the pointer dereference. Cc: Ulf Hansson Cc: Xiyu Yang Cc: Xin Xiong Cc: Xin Tan Cc: Tony Lindgren Cc: Yang Li Cc: linux-mmc@vger.kernel.org Cc: stable Reported-by: whitehat002 Signed-off-by: Greg Kroah-Hartman Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org Signed-off-by: Ulf Hansson

mmc: core: Wait for command setting 'Power Off Notification' bit to complete

2022-01-24T14:37:13Z

SD card is allowed to signal busy on DAT0 up to 1s after the CMD49. According to SD spec (version 6.0 section 5.8.1.3) first host waits until busy of CMD49 is released and only then polls Power Management Status register up to 1s until the card indicates ready to power off. Without waiting for busy before polling status register sometimes card becomes unresponsive and system fails to suspend: [ 205.907459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 206.421274] sunxi-mmc 1c0f000.mmc: data error, sending stop command [ 206.421321] sunxi-mmc 1c0f000.mmc: send stop command failed [ 206.421347] mmc0: error -110 reading status reg of PM func [ 206.421366] PM: dpm_run_callback(): mmc_bus_suspend+0x0/0x74 returns -110 [ 206.421402] mmcblk mmc0:aaaa: PM: failed to suspend async: error -110 [ 206.437064] PM: Some devices failed to suspend, or early wake event detected Tested with Sandisk Extreme PRO A2 64GB on Allwinner A64 system. Signed-off-by: Andrey Skvortsov Fixes: 2c5d42769038 ("mmc: core: Add support for Power Off Notification for SD cards") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220115121447.641524-1-andrej.skvortzov@gmail.com Signed-off-by: Ulf Hansson

mmc: sh_mmcif: Check for null res pointer

2022-01-24T14:37:13Z

If there is no suitable resource, platform_get_resource() will return NULL. Therefore in order to avoid the dereference of the NULL pointer, it should be better to check the 'res'. Signed-off-by: Jiasheng Jiang Cc: stable@vger.kernel.org # v5.16+ Link: https://lore.kernel.org/r/20220119120006.1426964-1-jiasheng@iscas.ac.cn Signed-off-by: Ulf Hansson

mmc: sdhci-of-esdhc: Check for error num after setting mask

2022-01-24T14:37:13Z

Because of the possible failure of the dma_supported(), the dma_set_mask_and_coherent() may return error num. Therefore, it should be better to check it and return the error if fails. And since the sdhci_setup_host() has already checked the return value of the enable_dma, we need not check it in sdhci_resume_host() again. Fixes: 5552d7ad596c ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips") Signed-off-by: Jiasheng Jiang Acked-by: Adrian Hunter Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220112083156.1124782-1-jiasheng@iscas.ac.cn Signed-off-by: Ulf Hansson

Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux

2022-01-23T04:20:44Z

Pull bitmap updates from Yury Norov: - introduce for_each_set_bitrange() - use find_first_*_bit() instead of find_next_*_bit() where possible - unify for_each_bit() macros * tag 'bitmap-5.17-rc1' of git://github.com/norov/linux: vsprintf: rework bitmap_list_string lib: bitmap: add performance test for bitmap_print_to_pagebuf bitmap: unify find_bit operations mm/percpu: micro-optimize pcpu_is_populated() Replace for_each_*_bit_from() with for_each_*_bit() where appropriate find: micro-optimize for_each_{set,clear}_bit() include/linux: move for_each_bit() macros from bitops.h to find.h cpumask: replace cpumask_next_* with cpumask_first_* where appropriate tools: sync tools/bitmap with mother linux all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate cpumask: use find_first_and_bit() lib: add find_first_and_bit() arch: remove GENERIC_FIND_FIRST_BIT entirely include: move find.h from asm_generic to linux bitops: move find_bit_*_le functions from le.h to find.h bitops: protect find_first_{,zero}_bit properly

Merge tag 'pm-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

2022-01-18T07:13:30Z

Pull more power management updates from Rafael Wysocki: "This is a continuation of the rework of device power management macros used for declaring device power management callbacks (Paul Cercueil)" * tag 'pm-5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: iio: pressure: bmp280: Use new PM macros PM: runtime: Add EXPORT[_GPL]_RUNTIME_DEV_PM_OPS macros PM: runtime: Add DEFINE_RUNTIME_DEV_PM_OPS() macro PM: core: Add EXPORT[_GPL]_SIMPLE_DEV_PM_OPS macros PM: core: Remove static qualifier in DEFINE_SIMPLE_DEV_PM_OPS macro PM: core: Remove DEFINE_UNIVERSAL_DEV_PM_OPS() macro

bitmap: unify find_bit operations

2022-01-15T16:47:31Z

bitmap_for_each_{set,clear}_region() are similar to for_each_bit() macros in include/linux/find.h, but interface and implementation of them are different. This patch adds for_each_bitrange() macros and drops unused bitmap_*_region() API in sake of unification. Signed-off-by: Yury Norov Tested-by: Wolfram Sang Acked-by: Dennis Zhou Acked-by: Ulf Hansson # For MMC