linux/drivers/mmc, branch v5.3

mmc: tmio: Fixup runtime PM management during remove

2019-09-13T11:49:09Z

Accessing the device when it may be runtime suspended is a bug, which is the case in tmio_mmc_host_remove(). Let's fix the behaviour. Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Tested-by: Geert Uytterhoeven

mmc: tmio: Fixup runtime PM management during probe

2019-09-13T11:49:04Z

The tmio_mmc_host_probe() calls pm_runtime_set_active() to update the runtime PM status of the device, as to make it reflect the current status of the HW. This works fine for most cases, but unfortunate not for all. Especially, there is a generic problem when the device has a genpd attached and that genpd have the ->start|stop() callbacks assigned. More precisely, if the driver calls pm_runtime_set_active() during ->probe(), genpd does not get to invoke the ->start() callback for it, which means the HW isn't really fully powered on. Furthermore, in the next phase, when the device becomes runtime suspended, genpd will invoke the ->stop() callback for it, potentially leading to usage count imbalance problems, depending on what's implemented behind the callbacks of course. To fix this problem, convert to call pm_runtime_get_sync() from tmio_mmc_host_probe() rather than pm_runtime_set_active(). Additionally, to avoid bumping usage counters and unnecessary re-initializing the HW the first time the tmio driver's ->runtime_resume() callback is called, introduce a state flag to keeping track of this. Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson Tested-by: Geert Uytterhoeven

Revert "mmc: tmio: move runtime PM enablement to the driver implementations"

2019-09-13T11:48:35Z

This reverts commit 7ff213193310ef8d0ee5f04f79d791210787ac2c. It turns out that the above commit introduces other problems. For example, calling pm_runtime_set_active() must not be done prior calling pm_runtime_enable() as that makes it fail. This leads to additional problems, such as clock enables being wrongly balanced. Rather than fixing the problem on top, let's start over by doing a revert. Fixes: 7ff213193310 ("mmc: tmio: move runtime PM enablement to the driver implementations") Signed-off-by: Ulf Hansson Tested-by: Geert Uytterhoeven

Revert "mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host controller"

2019-09-11T13:57:21Z

This reverts commit 414126f9e5abf1973c661d24229543a9458fa8ce. This commit broke eMMC storage access on a new consumer MiniPC based on AMD SoC, which has eMMC connected to: 02:00.0 SD Host controller: O2 Micro, Inc. Device 8620 (rev 01) (prog-if 01) Subsystem: O2 Micro, Inc. Device 0002 During probe, several errors are seen including: mmc1: Got data interrupt 0x02000000 even though no data operation was in progress. mmc1: Timeout waiting for hardware interrupt. mmc1: error -110 whilst initialising MMC card Reverting this commit allows the eMMC storage to be detected & usable again. Signed-off-by: Daniel Drake Fixes: 414126f9e5ab ("mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host controller") Cc: stable@vger.kernel.org # v5.1+ Signed-off-by: Ulf Hansson

Revert "mmc: bcm2835: Terminate timeout work synchronously"

2019-09-11T13:57:21Z

The commit 37fefadee8bb ("mmc: bcm2835: Terminate timeout work synchronously") causes lockups in case of hardware timeouts due the timeout work also calling cancel_delayed_work_sync() on its own. So revert it. Fixes: 37fefadee8bb ("mmc: bcm2835: Terminate timeout work synchronously") Cc: stable@vger.kernel.org Signed-off-by: Stefan Wahren Signed-off-by: Ulf Hansson

Revert "mmc: core: do not retry CMD6 in __mmc_switch()"

2019-09-03T14:53:28Z

Turns out the commit 3a0681c7448b ("mmc: core: do not retry CMD6 in __mmc_switch()") breaks initialization of a Toshiba THGBMNG5 eMMC card, when using the meson-gx-mmc.c driver on a custom board based on Amlogic A113D. The CMD6 that switches the card into HS200 mode is then one that fails and according to the below printed messages from the log: [ 1.648951] mmc0: mmc_select_hs200 failed, error -84 [ 1.648988] mmc0: error -84 whilst initialising MMC card After some analyze, it turns out that adding a delay of ~5ms inside mmc_select_bus_width() but after mmc_compare_ext_csds() has been executed, also fixes the problem. Adding yet some more debug code, trying to figure out if potentially the card could be in a busy state, both by using CMD13 and ->card_busy() ops concluded that this was not the case. Therefore, let's simply revert the commit that dropped support for retrying of CMD6, as this also fixes the problem. Fixes: 3a0681c7448b ("mmc: core: do not retry CMD6 in __mmc_switch()") Cc: stable@vger.kernel.org Signed-off-by: Jan Kaisrlik Signed-off-by: Ulf Hansson

mmc: sdhci-cadence: enable v4_mode to fix ADMA 64-bit addressing

2019-08-30T07:17:53Z

The IP datasheet says this controller is compatible with SD Host Specification Version v4.00. As it turned out, the ADMA of this IP does not work with 64-bit mode when it is in the Version 3.00 compatible mode; it understands the old 64-bit descriptor table (as defined in SDHCI v2), but the ADMA System Address Register (SDHCI_ADMA_ADDRESS) cannot point to the 64-bit address. I noticed this issue only after commit bd2e75633c80 ("dma-contiguous: use fallback alloc_pages for single pages"). Prior to that commit, dma_set_mask_and_coherent() returned the dma address that fits in 32-bit range, at least for the default arm64 configuration (arch/arm64/configs/defconfig). Now the host->adma_addr exceeds the 32-bit limit, causing the real problem for the Socionext SoCs. (As a side-note, I was also able to reproduce the issue for older kernels by turning off CONFIG_DMA_CMA.) Call sdhci_enable_v4_mode() to fix this. Cc: # v4.20+ Signed-off-by: Masahiro Yamada Signed-off-by: Ulf Hansson

mmc: sdhci-sprd: clear the UHS-I modes read from registers

2019-08-30T07:17:53Z

sprd's sd host controller supports SDR50/SDR104/DDR50 though, the UHS-I mode used by the specific card can be selected via devicetree only. Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller") Signed-off-by: Chunyan Zhang Signed-off-by: Chunyan Zhang Reviewed-by: Baolin Wang Tested-by: Baolin Wang Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson

mms: sdhci-sprd: add SDHCI_QUIRK_BROKEN_CARD_DETECTION

2019-08-30T07:17:53Z

sprd's sd host controller doesn't support detection to card insert or remove. Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller") Signed-off-by: Chunyan Zhang Signed-off-by: Chunyan Zhang Reviewed-by: Baolin Wang Tested-by: Baolin Wang Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson

mmc: sdhci-sprd: add SDHCI_QUIRK2_PRESET_VALUE_BROKEN

2019-08-30T07:17:53Z

The bit of PRESET_VAL_ENABLE in HOST_CONTROL2 register is reserved on sprd's sd host controller, set quirk2 to disable configuring this. Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller") Signed-off-by: Chunyan Zhang Signed-off-by: Chunyan Zhang Reviewed-by: Baolin Wang Tested-by: Baolin Wang Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson