linux/drivers/net/can, branch v4.5

can: mcp251x: avoid write to error flag register if it's unnecessary

2016-03-04T07:45:17Z

Only two bits (RX0OVR and RX1OVR) are writable in EFLG, write is useless if these bits aren't set. Signed-off-by: Ed Spiridonov Signed-off-by: Marc Kleine-Budde

can: gs_usb: fixed disconnect bug by removing erroneous use of kfree()

2016-02-26T07:36:33Z

gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is allocated through alloc_candev() and should instead be freed using free_candev() alone. The inappropriate use of kfree() causes the kernel to hang when gs_destroy_candev() is called. Only the struct gs_usb * which is allocated through kzalloc() should be freed using kfree() when the device is disconnected. Signed-off-by: Maximilian Schneider Cc: linux-stable Signed-off-by: Marc Kleine-Budde

can: ems_usb: Fix possible tx overflow

2016-02-21T14:09:12Z

This patch fixes the problem that more CAN messages could be sent to the interface as could be send on the CAN bus. This was more likely for slow baud rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under heavy TX load this produced another bulk transfer without checking the free_slots variable and hence caused the overflow in the interface. Signed-off-by: Gerhard Uttenthaler Cc: linux-stable Signed-off-by: Marc Kleine-Budde

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2015-12-04T02:09:12Z

Conflicts: drivers/net/ethernet/renesas/ravb_main.c kernel/bpf/syscall.c net/ipv4/ipmr.c All three conflicts were cases of overlapping changes. Signed-off-by: David S. Miller

can: xilinx: Convert to runtime_pm

2015-11-23T08:51:34Z

Instead of enabling/disabling clocks at several locations in the driver, Use the runtime_pm framework. This consolidates the actions for runtime PM In the appropriate callbacks and makes the driver more readable and mantainable. Signed-off-by: Kedareswara rao Appana Signed-off-by: Marc Kleine-Budde

can: remove obsolete assignment for CAN protocol error type

2015-11-23T08:37:38Z

The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is initialized with zero in alloc_can_err_skb() anyway. So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we can remove the obsolete OR operation entirely. Signed-off-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde

can: fix assignment of error location in CAN error messages

2015-11-23T08:37:34Z

As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187 the assignment of the error location in CAN error messages had some bit wise overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines a single value which points to a location inside the CAN frame on the wire. This patch fixes the assignments for the error locations in error messages. Reported-by: Dan Carpenter Signed-off-by: Oliver Hartkopp Signed-off-by: Marc Kleine-Budde

can: sja1000: clear interrupts on start

2015-11-23T08:35:21Z

According to SJA1000 data sheet error-warning (EI) interrupt is not cleared by setting the controller in to reset-mode. Then if we have the following case: - system is suspended (echo mem > /sys/power/state) and SJA1000 is left in operating state - A bus error condition occurs which activates EI interrupt, system is still suspended which means EI interrupt will be not be handled nor cleared. If the above two events occur, on resume there is no way to return the SJA1000 to operating state, except to cycle power to it. By simply reading the IR register on start we will clear any previous conditions that could be present. Signed-off-by: Mirza Krak Reported-by: Christian Magnusson Cc: linux-stable Signed-off-by: Marc Kleine-Budde

Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

2015-11-05T21:15:12Z

Pull spi updates from Mark Brown: "Quite a lot of activity in SPI this cycle, almost all of it in drivers with a few minor improvements and tweaks in the core. - Updates to pxa2xx to support Intel Broxton and multiple chip selects. - Support for big endian in the bcm63xx driver. - Multiple slave support for the mt8173 - New driver for the auxiliary SPI controller in bcm2835 SoCs. - Support for Layerscale SoCs in the Freescale DSPI driver" * tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits) spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI spi: pxa2xx: Add support for Intel Broxton spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals spi: pxa2xx: Add output control for multiple Intel LPSS chip selects spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific spi: Add DSPI support for layerscape family spi: ti-qspi: improve ->remove() callback spi/spi-xilinx: Fix race condition on last word read spi: Drop owner assignment from spi_drivers spi: Add THIS_MODULE to spi_driver in SPI core spi: Setup the master controller driver before setting the chipselect spi: dw: replace magic constant by DW_SPI_DR spi: mediatek: mt8173 spi multiple devices support spi: mediatek: handle controller_data in mtk_spi_setup spi: mediatek: remove mtk_spi_config spi: mediatek: Update document devicetree bindings to support multiple devices spi: fix kernel-doc warnings about missing return desc in spi.c spi: fix kernel-doc warnings about missing return desc in spi.h spi: pxa2xx: Align a few defines spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select ...

Merge remote-tracking branches 'spi/topic/omap-100k', 'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next

2015-11-04T11:02:12Z