linux/drivers/net/phy/icplus.c, branch v4.5

phy: Centralize setting driver module owner

2016-01-07T19:31:27Z

Rather than have each driver set the driver owner field, do it once in the core code. This will also help with later changes, when the device structure will move. Signed-off-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

phy: Add an mdio_device structure

2016-01-07T19:31:26Z

Not all devices attached to an MDIO bus are phys. So add an mdio_device structure to represent the generic parts of an mdio device, and place this structure into the phy_device. Signed-off-by: Andrew Lunn Signed-off-by: David S. Miller

net: phy: Utilize phy_interface_is_rgmii

2015-05-27T04:27:35Z

Update all open-coded tests for all 4 PHY_INTERFACE_MODE_RGMII* values to use the newly introduced helper: phy_interface_is_rgmii. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller

net: phy: replace phy_drivers_register calls

2014-11-12T18:52:53Z

Replace module init/exit which only calls phy_drivers_register with module_phy_driver macro. Tested using Micrel driver, and otherwise compile-tested only. Signed-off-by: Johan Hovold Signed-off-by: David S. Miller

net: phy: icplus: fix checkpath error

2013-12-18T05:49:02Z

Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller

net: phy: icplus: fix broken INTR pin settings

2013-01-28T05:08:22Z

This patch fixes the setting of the INTR pin that is valid for IP101 A/G device and not for the IP1001. Reported-by: Anunay Saxena Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller

net: phy: icplus: Use the RGMII interface mode to configure clock delays

2013-01-28T05:08:22Z

Like several other PHY devices which support RGMII, the IC+1001 allows additional delays to by added to the RX_CLK and TX_CLK signals to compensate for skew between the clock and data signals. Previously this was always enabled, but this change makes use of the different RGMII interface modes to allow the user to specify whether this should be enabled. Signed-off-by: Stuart Menefy Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller

phylib: Support registering a bunch of drivers

2012-07-09T07:10:56Z

If registering of one of them fails, all already registered drivers of this module will be unregistered. Use the new register/unregister functions in all drivers registering more than one driver. amd.c, realtek.c: Simplify: directly return registration result. Tested with broadcom.c All others compile-tested. Signed-off-by: Christian Hohnstaedt Signed-off-by: David S. Miller

net: icplus: fix interrupt mask

2012-06-04T16:02:40Z

This patch fixes the interrupt mask for IC101 A/G devices and now enables the link/speed/duplex interrupts. This is done by setting the "INTR pin used" bit and cleaning all the other bits in the Register 17. Reported-by: Stuart Menefy Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller

icplus: fix interrupt for IC+ 101A/G and 1001LF

2012-04-19T19:34:18Z

This patch fixes and adds the irq handler for the IC+ 101A/G where we need to read the reg17 to clean the irq. Also remove the flag for the 1001LF where no interrupt can be used for this device. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller