linux/drivers/net/phy, branch v4.15

mdio-sun4i: Fix a memory leak

2018-01-08T19:30:28Z

If the probing of the regulator is deferred, the memory allocated by 'mdiobus_alloc_size()' will be leaking. It should be freed before the next call to 'sun4i_mdio_probe()' which will reallocate it. Fixes: 4bdcb1dd9feb ("net: Add MDIO bus driver for the Allwinner EMAC") Signed-off-by: Christophe JAILLET Signed-off-by: David S. Miller

phylink: mark expected switch fall-throughs in phylink_mii_ioctl

2018-01-08T19:21:58Z

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1463447 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva Signed-off-by: David S. Miller

sfp: fix sfp-bus oops when removing socket/upstream

2018-01-02T18:40:28Z

When we remove a socket or upstream, and the other side isn't registered, we dereference a NULL pointer, causing a kernel oops. Fix this. Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Signed-off-by: Russell King Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

phylink: ensure we report link down when LOS asserted

2018-01-02T18:39:11Z

Although we disable the netdev carrier, we fail to report in the kernel log that the link went down. Fix this. Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround

2017-12-26T17:26:43Z

Under some circumstances driver will perform PHY reset in ksz9031_read_status() to fix autoneg failure case (idle error count = 0xFF). When this happens ksz9031 will not detect link status change any more when connecting to Netgear 1G switch (link can be recovered sometimes by restarting netdevice "ifconfig down up"). Reproduced with TI am572x board equipped with ksz9031 PHY while connecting to Netgear 1G switch. Fix the issue by reconfiguring autonegotiation after PHY reset in ksz9031_read_status(). Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg") Signed-off-by: Grygorii Strashko Signed-off-by: David S. Miller

phylink: ensure AN is enabled

2017-12-26T02:47:20Z

Ensure that we mark AN as enabled at boot time, rather than leaving it disabled. This is noticable if your SFP module is fiber, and it supports faster speeds than 1G with 2.5G support in place. Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

phylink: ensure the PHY interface mode is appropriately set

2017-12-26T02:47:19Z

When setting the ethtool settings, ensure that the validated PHY interface mode is propagated to the current link settings, so that 2500BaseX can be selected. Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Russell King Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: phy: xgene: disable clk on error paths

2017-12-18T20:09:42Z

There are several error paths in xgene_mdio_probe(), where clk is left undisabled. The patch fixes them. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov Signed-off-by: David S. Miller

net: phy: marvell: avoid pause mode on SGMII-to-Copper for 88e151x

2017-12-18T20:04:44Z

Observed on the 88e1512 in SGMII-to-Copper mode, negotiating pause is unreliable. While the pause bits can be set in the advertisment register, they clear shortly after negotiation with a link partner commences irrespective of the cause of the negotiation. While these bits may be correctly conveyed to the link partner on the first negotiation, a subsequent negotiation (eg, due to negotiation restart by the link partner, or reconnection of the cable) will result in the link partner seeing these bits as zero, while the kernel believes that it has advertised pause modes. This leads to the local kernel evaluating (eg) symmetric pause mode, while the remote end evaluates that we have no pause mode capability. Since we can't guarantee the advertisment, disable pause mode support with this PHY when used in SGMII-to-Copper mode. The 88e1510 in RGMII-to-Copper mode appears to behave correctly. Reviewed-by: Andrew Lunn Signed-off-by: Russell King Signed-off-by: David S. Miller

net: phy: marvell: Limit 88m1101 autoneg errata to 88E1145 as well.

2017-12-18T18:19:17Z

88E1145 also need this autoneg errata. Fixes: f2899788353c ("net: phy: marvell: Limit errata to 88m1101") Signed-off-by: Zhao Qiang Signed-off-by: David S. Miller