linux/drivers/net/phy, branch v5.3

net: phylink: Fix flow control resolution

2019-09-07T15:26:13Z

Regarding to IEEE 802.3-2015 standard section 2 28B.3 Priority resolution - Table 28-3 - Pause resolution In case of Local device Pause=1 AsymDir=0, Link partner Pause=1 AsymDir=1, Local device resolution should be enable PAUSE transmit, disable PAUSE receive. And in case of Local device Pause=1 AsymDir=1, Link partner Pause=1 AsymDir=0, Local device resolution should be enable PAUSE receive, disable PAUSE transmit. Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Stefan Chulski Reported-by: Shaul Ben-Mayor Acked-by: Russell King Signed-off-by: David S. Miller

Add genphy_c45_config_aneg() function to phy-c45.c

2019-08-28T03:21:15Z

Commit 34786005eca3 ("net: phy: prevent PHYs w/o Clause 22 regs from calling genphy_config_aneg") introduced a check that aborts phy_config_aneg() if the phy is a C45 phy. This causes phy_state_machine() to call phy_error() so that the phy ends up in PHY_HALTED state. Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg() (analogous to the C22 case) so that the state machine can run correctly. genphy_c45_config_aneg() closely resembles mv3310_config_aneg() in drivers/net/phy/marvell10g.c, excluding vendor specific configurations for 1000BaseT. Fixes: 22b56e827093 ("net: phy: replace genphy_10g_driver with genphy_c45_driver") Signed-off-by: Marco Hartmann Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phy: consider AN_RESTART status when reading link status

2019-08-14T02:49:01Z

After configuring and restarting aneg we immediately try to read the link status. On some systems the PHY may not yet have cleared the "aneg complete" and "link up" bits, resulting in a false link-up signal. See [0] for a report. Clause 22 and 45 both require the PHY to keep the AN_RESTART bit set until the PHY actually starts auto-negotiation. Let's consider this in the generic functions for reading link status. The commit marked as fixed is the first one where the patch applies cleanly. [0] https://marc.info/?t=156518400300003&r=1&w=2 Fixes: c1164bb1a631 ("net: phy: check PMAPMD link status only in genphy_c45_read_link") Tested-by: Yonglong Liu Signed-off-by: Heiner Kallweit Reviewed-by: Andrew Lunn Signed-off-by: Jakub Kicinski

net: phy: at803x: stop switching phy delay config needlessly

2019-08-12T21:02:29Z

This driver does a funny dance disabling and re-enabling RX and/or TX delays. In any of the RGMII-ID modes, it first disables the delays, just to re-enable them again right away. This looks like a needless exercise. Just enable the respective delays when in any of the relevant 'id' modes, and disable them otherwise. Also, remove comments which don't add anything that can't be seen by looking at the code. Signed-off-by: André Draszik CC: Andrew Lunn CC: Florian Fainelli CC: Heiner Kallweit CC: "David S. Miller" CC: netdev@vger.kernel.org Signed-off-by: David S. Miller

net: phy: fix race in genphy_update_link

2019-08-03T01:16:04Z

In phy_start_aneg() autoneg is started, and immediately after that link and autoneg status are read. As reported in [0] it can happen that at time of this read the PHY has reset the "aneg complete" bit but not yet the "link up" bit, what can result in a false link-up detection. To fix this don't report link as up if we're in aneg mode and PHY doesn't signal "aneg complete". [0] https://marc.info/?t=156413509900003&r=1&w=2 Fixes: 4950c2ba49cc ("net: phy: fix autoneg mismatch case in genphy_read_status") Reported-by: liuyonglong Tested-by: liuyonglong Signed-off-by: Heiner Kallweit Signed-off-by: David S. Miller

net: phy: phy_led_triggers: Fix a possible null-pointer dereference in phy_led_trigger_change_speed()

2019-07-31T22:56:11Z

In phy_led_trigger_change_speed(), there is an if statement on line 48 to check whether phy->last_triggered is NULL: if (!phy->last_triggered) When phy->last_triggered is NULL, it is used on line 52: led_trigger_event(&phy->last_triggered->trigger, LED_OFF); Thus, a possible null-pointer dereference may occur. To fix this bug, led_trigger_event(&phy->last_triggered->trigger, LED_OFF) is called when phy->last_triggered is not NULL. This bug is found by a static analysis tool STCheck written by the OSLAB group in Tsinghua University. Signed-off-by: Jia-Ju Bai Signed-off-by: David S. Miller

net: phy: fixed_phy: print gpio error only if gpio node is present

2019-07-30T16:54:45Z

It is perfectly ok to not have an gpio attached to the fixed-link node. So the driver should not throw an error message when the gpio is missing. Fixes: 5468e82f7034 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()") Signed-off-by: Hubert Feurstein Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phylink: Fix flow control for fixed-link

2019-07-27T21:27:51Z

In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND with pl->supported, pl->supported is zeroed and only the speed/duplex modes and MII bits are set. So pl->link_config.advertising always loses the flow control/pause bits. By setting Pause and Asym_Pause bits in pl->supported, the flow control work again when devicetree "pause" is set in fixes-link node and the MAC advertise that is supports pause. Results with this patch. Legend: - DT = 'Pause' is set in the fixed-link in devicetree. - validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the validate(). - flow = results reported my link is Up line. +-----+------------+-------+ | DT | validate() | flow | +-----+------------+-------+ | Yes | Yes | rx/tx | | No | Yes | off | | Yes | No | off | +-----+------------+-------+ Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: René van Dorst Acked-by: Russell King Signed-off-by: David S. Miller

net: phy: mscc: initialize stats array

2019-07-24T22:25:44Z

The memory allocated for the stats array may contain arbitrary data. Fixes: e4f9ba642f0b ("net: phy: mscc: add support for VSC8514 PHY.") Fixes: 00d70d8e0e78 ("net: phy: mscc: add support for VSC8574 PHY") Fixes: a5afc1678044 ("net: phy: mscc: add support for VSC8584 PHY") Fixes: f76178dc5218 ("net: phy: mscc: add ethtool statistics counters") Signed-off-by: Andreas Schwab Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phylink: don't start and stop SGMII PHYs in SFP modules twice

2019-07-24T21:37:15Z

SFP modules connected using the SGMII interface have their own PHYs which are handled by the struct phylink's phydev field. On the other hand, for the modules connected using 1000Base-X interface that field is not set. Since commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") phylink_start() ends up setting the phydev field using the sfp-bus infrastructure, which eventually calls phy_start() on it, and then calling phy_start() again on the same phydev from phylink_start() itself. Similar call sequence holds for phylink_stop(), only in the reverse order. This results in WARNs during network interface bringup and shutdown when a copper SFP module is connected, as phy_start() and phy_stop() are called twice in a row for the same phy_device: % ip link set up dev eth0 ------------[ cut here ]------------ called from state UP WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0 Modules linked in: CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1 NIP: c0227bf0 LR: c0227bf0 CTR: c004d224 REGS: df547720 TRAP: 0700 Not tainted (5.2.0+) MSR: 00029000 CR: 24002822 XER: 00000000 GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001 GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000 GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000 GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00 NIP [c0227bf0] phy_start+0x74/0xc0 LR [c0227bf0] phy_start+0x74/0xc0 Call Trace: [df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable) [df5477e8] [c023cad0] startup_gfar+0x398/0x3f4 [df547828] [c023cf08] gfar_enet_open+0x364/0x374 [df547898] [c029d870] __dev_open+0xe4/0x140 [df5478c8] [c029db70] __dev_change_flags+0xf0/0x188 [df5478f8] [c029dc28] dev_change_flags+0x20/0x54 [df547918] [c02ae304] do_setlink+0x310/0x818 [df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0 [df547c28] [c02b222c] rtnl_newlink+0x48/0x68 [df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c [df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0 [df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c [df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0 [df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40 [df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc [df547e98] [c027df7c] __sys_sendmsg+0x68/0x84 [df547ef8] [c027e430] sys_socketcall+0x1a0/0x204 [df547f38] [c000d1d8] ret_from_syscall+0x0/0x38 --- interrupt: c01 at 0xfd4e030 LR = 0xfd4e010 Instruction dump: 813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e 3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0 ---[ end trace d4c095aeaf6ea998 ]--- and % ip link set down dev eth0 ------------[ cut here ]------------ called from state HALTED WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88 <...> Call Trace: [df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable) [df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44 [df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c [df581848] [c022f04c] sfp_upstream_stop+0x34/0x44 [df581858] [c0225608] phylink_stop+0x7c/0xe4 [df581868] [c023c57c] stop_gfar+0x7c/0x94 [df581888] [c023c5b8] gfar_close+0x24/0x94 [df5818a8] [c0298688] __dev_close_many+0xdc/0xf8 [df5818c8] [c029db58] __dev_change_flags+0xd8/0x188 [df5818f8] [c029dc28] dev_change_flags+0x20/0x54 [df581918] [c02ae304] do_setlink+0x310/0x818 [df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0 [df581c28] [c02b222c] rtnl_newlink+0x48/0x68 [df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c [df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0 [df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c [df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0 [df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40 [df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc [df581e98] [c027df7c] __sys_sendmsg+0x68/0x84 [df581ef8] [c027e430] sys_socketcall+0x1a0/0x204 [df581f38] [c000d1d8] ret_from_syscall+0x0/0x38 <...> ---[ end trace d4c095aeaf6ea999 ]--- SFP modules with the 1000Base-X interface are not affected. Place explicit calls to phy_start() and phy_stop() before enabling or after disabling an attached SFP module, where phydev is not yet set (or is already unset), so they will be made only from the inside of sfp-bus, if needed. Fixes: 217962615662 ("net: phy: warn if phy_start is called from invalid state") Signed-off-by: Arseny Solokha Acked-by: Russell King Signed-off-by: David S. Miller