linux/drivers/net/phy, branch v6.14

phy: fix xa_alloc_cyclic() error handling

2025-03-19T09:57:37Z

xa_alloc_cyclic() can return 1, which isn't an error. To prevent situation when the caller of this function will treat it as no error do a check only for negative here. Fixes: 384968786909 ("net: phy: Introduce ethernet link topology representation") Signed-off-by: Michal Swiatkowski Reviewed-by: Maxime Chevallier Signed-off-by: David S. Miller

net: phy: nxp-c45-tja11xx: add TJA112XB SGMII PCS restart errata

2025-03-08T03:54:25Z

TJA1120B/TJA1121B can achieve a stable operation of SGMII after a startup event by putting the SGMII PCS into power down mode and restart afterwards. It is necessary to put the SGMII PCS into power down mode and back up. Cc: stable@vger.kernel.org Fixes: f1fe5dff2b8a ("net: phy: nxp-c45-tja11xx: add TJA1120 support") Signed-off-by: Andrei Botila Link: https://patch.msgid.link/20250304160619.181046-3-andrei.botila@oss.nxp.com Signed-off-by: Jakub Kicinski

net: phy: nxp-c45-tja11xx: add TJA112X PHY configuration errata

2025-03-08T03:54:25Z

The most recent sillicon versions of TJA1120 and TJA1121 can achieve full silicon performance by putting the PHY in managed mode. It is necessary to apply these PHY writes before link gets established. Application of this fix is required after restart of device and wakeup from sleep. Cc: stable@vger.kernel.org Fixes: f1fe5dff2b8a ("net: phy: nxp-c45-tja11xx: add TJA1120 support") Signed-off-by: Andrei Botila Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250304160619.181046-2-andrei.botila@oss.nxp.com Signed-off-by: Jakub Kicinski

net: phy: qcom: qca807x fix condition for DAC_DSP_BIAS_CURRENT

2025-02-20T21:19:35Z

While setting the DAC value, the wrong boolean value is evaluated to set the DSP bias current. So let's correct the conditional statement and use the right boolean value read from the DTS set in the priv. Cc: stable@vger.kernel.org Fixes: d1cb613efbd3 ("net: phy: qcom: add support for QCA807x PHY Family") Signed-off-by: George Moussalem Signed-off-by: Christian Marangi Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250219130923.7216-1-ansuelsmth@gmail.com Signed-off-by: Jakub Kicinski

net: phylink: make configuring clock-stop dependent on MAC support

2025-02-12T00:08:34Z

We should not be configuring the PHYs clock-stop settings unless the MAC supports phylink managed EEE. Make this dependent on MAC support. This was noticed in a suspicious RCU usage report from the kernel test robot (the suspicious RCU usage due to calling phy_detach() remains unaddressed, but is triggered by the error this was generating.) Fixes: 03abf2a7c654 ("net: phylink: add EEE management") Signed-off-by: Russell King (Oracle) Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/E1tgjNn-003q0w-Pw@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski

net: phy: c45-tjaxx: add delay between MDIO write and read in soft_reset

2025-01-27T23:02:51Z

In application note (AN13663) for TJA1120, on page 30, there's a figure with average PHY startup timing values following software reset. The time it takes for SMI to become operational after software reset ranges roughly from 500 us to 1500 us. This commit adds 2000 us delay after MDIO write which triggers software reset. Without this delay, soft_reset function returns an error and prevents successful PHY init. Cc: stable@vger.kernel.org Fixes: b050f2f15e04 ("phy: nxp-c45: add driver for tja1103") Signed-off-by: Milos Reljin Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/AM8P250MB0124D258E5A71041AF2CC322E1E32@AM8P250MB0124.EURP250.PROD.OUTLOOK.COM Signed-off-by: Jakub Kicinski

net: phy: marvell-88q2xxx: Fix temperature measurement with reset-gpios

2025-01-23T08:55:06Z

When using temperature measurement on Marvell 88Q2XXX devices and the reset-gpios property is set in DT, the device does a hardware reset when interface is brought down and up again. That means that the content of the register MDIO_MMD_PCS_MV_TEMP_SENSOR2 is reset to default and that leads to permanent deactivation of the temperature measurement, because activation is done in mv88q2xxx_probe. To fix this move activation of temperature measurement to mv88q222x_config_init. Fixes: a557a92e6881 ("net: phy: marvell-88q2xxx: add support for temperature sensor") Reviewed-by: Niklas Söderlund Signed-off-by: Dimitri Fedrau Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20250118-marvell-88q2xxx-fix-hwmon-v2-1-402e62ba2dcb@gmail.com Signed-off-by: Paolo Abeni

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

2025-01-21T09:24:33Z

No conflicts and no adjacent changes. Signed-off-by: Paolo Abeni

net: phylink: fix regression when binding a PHY

2025-01-21T00:32:42Z

Some PHYs don't support clause 45 access, and return -EOPNOTSUPP from phy_modify_mmd(), which causes phylink_bringup_phy() to fail. Prevent this failure by allowing -EOPNOTSUPP to also mean success. Reported-by: Jiawen Wu Tested-by: Jiawen Wu Signed-off-by: Russell King (Oracle) Reviewed-by: Simon Horman Link: https://patch.msgid.link/E1tZp1a-001V62-DT@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski

net: phy: realtek: HWMON support for standalone versions of RTL8221B and RTL8251

2025-01-20T12:30:56Z

HWMON support has been added for the RTL8221/8251 PHYs integrated together with the MAC inside the RTL8125/8126 chips. This patch extends temperature reading support for standalone variants of the mentioned PHYs. I don't know whether the earlier revisions of the RTL8226 also have a built-in temperature sensor, so they have been skipped for now. Tested on RTL8221B-VB-CG. Signed-off-by: Aleksander Jan Bajkowski Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller