linux/drivers/net/usb, branch v4.4

net: qmi_wwan: Add WeTelecom-WPD600N

2016-01-06T20:50:00Z

The WeTelecom-WPD600N is an LTE module that, in addition to supporting most "normal" bands, also supports LTE over 450MHz. Manual testing showed that only interface number three replies to QMI messages. Cc: Bjørn Mork Signed-off-by: Kristian Evensen Acked-by: Bjørn Mork Signed-off-by: David S. Miller

r8152: add reset_resume function

2016-01-05T03:02:08Z

When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set or not. If reset_resume() is called, it means the power supply is cut or the device is reset. That is, the device wouldn't be in runtime suspend state and the reinitialization is necessary. Signed-off-by: Hayes Wang Signed-off-by: David S. Miller

net: cdc_ncm: avoid changing RX/TX buffers on MTU changes

2015-12-24T03:52:08Z

NCM buffer sizes are negotiated with the device independently of the network device MTU. The RX buffers are allocated by the usbnet framework based on the rx_urb_size value set by cdc_ncm. A single RX buffer can hold a number of MTU sized packets. The default usbnet change_mtu ndo only modifies rx_urb_size if it is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size and hard_mtu independently of each other, based on dwNtbInMaxSize and dwNtbOutMaxSize respectively. It was therefore assumed that usbnet_change_mtu() would never touch rx_urb_size. This failed to consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens to be equal. Fix by implementing an NCM specific change_mtu ndo, modifying the netdev MTU without touching the buffer size settings. Signed-off-by: Bjørn Mork Signed-off-by: David S. Miller

net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card

2015-12-21T19:51:14Z

Unlike DW5550, Dell DW5813 is a mobile broadband card with no ARP capabilities: the patch makes this device to use wwan_noarp_info struct Signed-off-by: Daniele Palmas Signed-off-by: David S. Miller

net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card

2015-12-21T19:51:14Z

Unlike DW5550, Dell DW5812 is a mobile broadband card with no ARP capabilities: the patch makes this device to use wwan_noarp_info struct Signed-off-by: Daniele Palmas Signed-off-by: David S. Miller

r8152: fix lockup when runtime PM is enabled

2015-12-09T03:48:01Z

When an interface is brought up which was previously suspended (via runtime PM), it would hang. This happens because napi_disable is called before napi_enable. Solve this by avoiding napi_enable in the resume during open function (netif_running is true when open is called, IFF_UP is set after a successful open; netif_running is false when close is called, but IFF_UP is then still set). While at it, remove WORK_ENABLE check from rtl8152_open (introduced with the original change) because it cannot happen: - After this patch, runtime resume will not set it during rtl8152_open. - When link is up, rtl8152_open is not called. - When link is down during system/auto suspend/resume, it is not set. Fixes: 41cec84cf285 ("r8152: don't enable napi before rx ready") Link: https://lkml.kernel.org/r/20151205105912.GA1766@al Signed-off-by: Peter Wu Acked-by: Hayes Wang Signed-off-by: David S. Miller

net: cdc_mbim: add "NDP to end" quirk for Huawei E3372

2015-12-06T04:35:34Z

The Huawei E3372 (12d1:157d) needs this quirk in MBIM mode as well. Allow this by forcing the NTB to contain only a single NDP, and add a device specific entry for this ID. Due to the way Huawei use device IDs, this might be applied to other modems as well. It is assumed that those modems will be based on the same firmware and will need this quirk too. If not, it will still not harm normal usage, although multiplexing performance could be impacted. Cc: Enrico Mioso Reported-by: Sami Farin Signed-off-by: Bjørn Mork Acked-By: Enrico Mioso Signed-off-by: David S. Miller

net: cdc_ncm: fix NULL pointer deref in cdc_ncm_bind_common

2015-11-24T19:26:16Z

Commit 77b0a099674a ("cdc-ncm: use common parser") added a dangerous new trust in the CDC functional descriptors presented by the device, unconditionally assuming that any device handled by the driver has a CDC Union descriptor. This descriptor is required by the NCM and MBIM specs, but crashing on non-compliant devices is still unacceptable. Not only will that allow malicious devices to crash the kernel, but in this case it is also well known that there are non-compliant real devices on the market - as shown by the comment accompanying the IAD workaround in the same function. The Sierra Wireless EM7305 is an example of such device, having a CDC header and a CDC MBIM descriptor but no CDC Union: Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 12 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 14 bInterfaceProtocol 0 iInterface 0 CDC Header: bcdCDC 1.10 CDC MBIM: bcdMBIMVersion 1.00 wMaxControlMessage 4096 bNumberFilters 16 bMaxFilterSize 128 wMaxSegmentSize 4064 bmNetworkCapabilities 0x20 8-byte ntb input size Endpoint Descriptor: .. The conversion to a common parser also left the local cdc_union variable untouched. This caused the IAD workaround code to be applied to all devices with an IAD descriptor, which was never intended. Finish the conversion by testing for hdr.usb_cdc_union_desc instead. Cc: Oliver Neukum Fixes: 77b0a099674a ("cdc-ncm: use common parser") Signed-off-by: Bjørn Mork Signed-off-by: David S. Miller

net: qmi_wwan: add XS Stick W100-2 from 4G Systems

2015-11-19T04:01:32Z

Thomas reports " 4gsystems sells two total different LTE-surfsticks under the same name. .. The newer version of XS Stick W100 is from "omega" .. Under windows the driver switches to the same ID, and uses MI03\6 for network and MI01\6 for modem. .. echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b01 Rev=02.32 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Now all important things are there: wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at) There is also ttyUSB0, but it is not usable, at least not for at. The device works well with qmi and ModemManager-NetworkManager. " Reported-by: Thomas Schäfer Signed-off-by: Bjørn Mork Signed-off-by: David S. Miller

net: usb: cdc_ether: add Dell DW5580 as a mobile broadband adapter

2015-11-16T19:58:39Z

Since Dell DW5580 is a 3G modem, this patch adds the device as a mobile broadband adapter Signed-off-by: Daniele Palmas Signed-off-by: David S. Miller