linux/drivers/net, branch v5.2

ipv6: constify rt6_nexthop()

2019-06-26T20:26:08Z

There is no functional change in this patch, it only prepares the next one. rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const variables. Signed-off-by: Nicolas Dichtel Reported-by: kbuild test robot Acked-by: Nick Desaulniers Signed-off-by: David S. Miller

net: dsa: microchip: Use gpiod_set_value_cansleep()

2019-06-26T20:22:29Z

Replace gpiod_set_value() with gpiod_set_value_cansleep(), as the switch reset GPIO can be connected to e.g. I2C GPIO expander and it is perfectly fine for the kernel to sleep for a bit in ksz_switch_register(). Signed-off-by: Marek Vasut Cc: Andrew Lunn Cc: Florian Fainelli Cc: Linus Walleij Cc: Tristram Ha Cc: Woojung Huh Reviewed-by: Andrew Lunn Reviewed-by: Linus Walleij Signed-off-by: David S. Miller

net: aquantia: fix vlans not working over bridged network

2019-06-26T20:16:45Z

In configuration of vlan over bridge over aquantia device it was found that vlan tagged traffic is dropped on chip. The reason is that bridge device enables promisc mode, but in atlantic chip vlan filters will still apply. So we have to corellate promisc settings with vlan configuration. The solution is to track in a separate state variable the need of vlan forced promisc. And also consider generic promisc configuration when doing vlan filter config. Fixes: 7975d2aff5af ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov Signed-off-by: Igor Russkikh Signed-off-by: David S. Miller

team: Always enable vlan tx offload

2019-06-26T17:14:08Z

We should rather have vlan_tci filled all the way down to the transmitting netdevice and let it do the hw/sw vlan implementation. Suggested-by: Jiri Pirko Signed-off-by: YueHaibing Signed-off-by: David S. Miller

bonding: Always enable vlan tx offload

2019-06-26T15:56:35Z

We build vlan on top of bonding interface, which vlan offload is off, bond mode is 802.3ad (LACP) and xmit_hash_policy is BOND_XMIT_POLICY_ENCAP34. Because vlan tx offload is off, vlan tci is cleared and skb push the vlan header in validate_xmit_vlan() while sending from vlan devices. Then in bond_xmit_hash, __skb_flow_dissect() fails to get information from protocol headers encapsulated within vlan, because 'nhoff' is points to IP header, so bond hashing is based on layer 2 info, which fails to distribute packets across slaves. This patch always enable bonding's vlan tx offload, pass the vlan packets to the slave devices with vlan tci, let them to handle vlan implementation. Fixes: 278339a42a1b ("bonding: propogate vlan_features to bonding master") Suggested-by: Jiri Pirko Signed-off-by: YueHaibing Acked-by: Jiri Pirko Signed-off-by: David S. Miller

qmi_wwan: Fix out-of-bounds read

2019-06-24T17:07:12Z

The syzbot reported Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x67/0x231 mm/kasan/report.c:188 __kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317 kasan_report+0xe/0x20 mm/kasan/common.c:614 qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417 usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361 really_probe+0x281/0x660 drivers/base/dd.c:509 driver_probe_device+0x104/0x210 drivers/base/dd.c:670 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 Caused by too many confusing indirections and casts. id->driver_info is a pointer stored in a long. We want the pointer here, not the address of it. Thanks-to: Hillf Danton Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com Cc: Kristian Evensen Fixes: e4bf63482c30 ("qmi_wwan: Add quirk for Quectel dynamic config") Signed-off-by: Bjørn Mork Signed-off-by: David S. Miller

net: macb: do not copy the mac address if NULL

2019-06-24T15:57:41Z

This patch fixes the MAC address setup in the probe. The MAC address retrieved using of_get_mac_address was checked for not containing an error, but it may also be NULL which wasn't tested. Fix it by replacing IS_ERR with IS_ERR_OR_NULL. Fixes: 541ddc66d665 ("net: macb: support of_get_mac_address new ERR_PTR error") Signed-off-by: Antoine Tenart Acked-by: Nicolas Ferre Signed-off-by: David S. Miller

sis900: fix TX completion

2019-06-22T23:46:32Z

Since commit 605ad7f184b60cfaacbc038aa6c55ee68dee3c89 "tcp: refine TSO autosizing", outbound throughput is dramatically reduced for some connections, as sis900 is doing TX completion within idle states only. Make TX completion happen after every transmitted packet. Test: netperf before patch: > netperf -H remote -l -2000000 -- -s 1000000 MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 327680 327680 253.44 0.06 after patch: > netperf -H remote -l -10000000 -- -s 1000000 MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 327680 327680 5.38 14.89 Thx to Dave Miller and Eric Dumazet for helpful hints Signed-off-by: Sergej Benilov Signed-off-by: David S. Miller

net: stmmac: set IC bit when transmitting frames with HW timestamp

2019-06-22T23:17:31Z

When transmitting certain PTP frames, e.g. SYNC and DELAY_REQ, the PTP daemon, e.g. ptp4l, is polling the driver for the frame transmit hardware timestamp. The polling will most likely timeout if the tx coalesce is enabled due to the Interrupt-on-Completion (IC) bit is not set in tx descriptor for those frames. This patch will ignore the tx coalesce parameter and set the IC bit when transmitting PTP frames which need to report out the frame transmit hardware timestamp to user space. Fixes: f748be531d70 ("net: stmmac: Rework coalesce timer and fix multi-queue races") Signed-off-by: Roland Hii Signed-off-by: Ong Boon Leong Signed-off-by: Voon Weifeng Signed-off-by: David S. Miller

net: stmmac: fixed new system time seconds value calculation

2019-06-22T23:16:23Z

When ADDSUB bit is set, the system time seconds field is calculated as the complement of the seconds part of the update value. For example, if 3.000000001 seconds need to be subtracted from the system time, this field is calculated as 2^32 - 3 = 4294967296 - 3 = 0x100000000 - 3 = 0xFFFFFFFD Previously, the 0x100000000 is mistakenly written as 100000000. This is further simplified from sec = (0x100000000ULL - sec); to sec = -sec; Fixes: ba1ffd74df74 ("stmmac: fix PTP support for GMAC4") Signed-off-by: Roland Hii Signed-off-by: Ong Boon Leong Signed-off-by: Voon Weifeng Signed-off-by: David S. Miller