linux/drivers/phy, branch v4.15

phy: work around 'phys' references to usb-nop-xceiv devices

2018-01-19T15:12:37Z

Stefan Wahren reports a problem with a warning fix that was merged for v4.15: we had lots of device nodes with a 'phys' property pointing to a device node that is not compliant with the binding documented in Documentation/devicetree/bindings/phy/phy-bindings.txt This generally works because USB HCD drivers that support both the generic phy subsystem and the older usb-phy subsystem ignore most errors from phy_get() and related calls and then use the usb-phy driver instead. However, it turns out that making the usb-nop-xceiv device compatible with the generic-phy binding changes the phy_get() return code from -EINVAL to -EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns -EPROBE_DEFER from its probe function rather than ignoring the failure, breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is enabled. The same code is used in the dwc3 driver and the usb_add_hcd() function, so a reasonable assumption would be that many other platforms are affected as well. I have reviewed all the related patches and concluded that "usb-nop-xceiv" is the only USB phy that is affected by the change, and since it is by far the most commonly referenced phy, all the other USB phy drivers appear to be used in ways that are are either safe in DT (they don't use the 'phys' property), or in the driver (they already ignore -EPROBE_DEFER from generic-phy when usb-phy is available). To work around the problem, this adds a special case to _of_phy_get() so we ignore any PHY node that is compatible with "usb-nop-xceiv", as we know that this can never load no matter how much we defer. In the future, we might implement a generic-phy driver for "usb-nop-xceiv" and then remove this workaround. Since we generally want older kernels to also want to work with the fixed devicetree files, it would be good to backport the patch into stable kernels as well (3.13+ are possibly affected), even though they don't contain any of the patches that may have caused regressions. Fixes: 014d6da6cb25 ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells Fixes: c5bbf358b790 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv Fixes: 44e5dced2ef6 arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv Fixes: f568f6f554b8 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv Fixes: d745d5f277bf ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv Fixes: 915fbe59cbf2 ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2 Link: https://patchwork.kernel.org/patch/10158145/ Cc: stable@vger.kernel.org Cc: Felipe Balbi Cc: Eric Anholt Tested-by: Stefan Wahren Acked-by: Rob Herring Tested-by: Hans Verkuil Acked-by: Kishon Vijay Abraham I Signed-off-by: Arnd Bergmann

phy: rcar-gen3-usb2: select USB_COMMON

2017-12-15T10:30:41Z

When USB is disabled, we get a link error for this driver because of the added OTG support drivers/phy/renesas/phy-rcar-gen3-usb2.o: In function `rcar_gen3_phy_usb2_probe': phy-rcar-gen3-usb2.c:(.text+0x250): undefined reference to `of_usb_get_dr_mode_by_phy' Other phy drivers select USB_COMMON for this, so let's do the same here. Fixes: 7e0540f41332 ("phy: rcar-gen3-usb2: check dr_mode for otg mode") Signed-off-by: Arnd Bergmann Acked-by: Yoshihiro Shimoda Signed-off-by: Kishon Vijay Abraham I

phy: rockchip-typec: add pm_runtime_disable in err case

2017-12-15T10:30:40Z

Add pm_runtime_disable in err case to make the pm_runtime_enable/disable is invoked balanced. Signed-off-by: Chris Zhong Reviewed-by: Brian Norris Reviewed-by: Douglas Anderson Signed-off-by: Kishon Vijay Abraham I

phy: cpcap-usb: Fix platform_get_irq_byname's error checking.

2017-12-15T10:30:39Z

The platform_get_irq_byname() function returns negative if an error occurs. zero or positive number on success. platform_get_irq_byname() error checking for zero is not correct. Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support") Signed-off-by: Arvind Yadav Reviewed-by: Sebastian Reichel Acked-by: Tony Lindgren Signed-off-by: Kishon Vijay Abraham I

phy: tegra: fix device-tree node lookups

2017-12-15T10:30:38Z

Fix child-node lookups during probe, which ended up searching the whole device tree depth-first starting at the parents rather than just matching on their children. To make things worse, some parent nodes could end up being being prematurely freed (by tegra_xusb_pad_register()) as of_find_node_by_name() drops a reference to its first argument. Fixes: 53d2a715c240 ("phy: Add Tegra XUSB pad controller support") Cc: stable # 4.7 Cc: Thierry Reding Signed-off-by: Johan Hovold Signed-off-by: Kishon Vijay Abraham I

Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2017-11-14T05:14:07Z

Pull USB/PHY updates from Greg KH: "Here is the big set of USB and PHY driver updates for 4.15-rc1. There is the usual amount of gadget and xhci driver updates, along with phy and chipidea enhancements. There's also a lot of SPDX tags and license boilerplate cleanups as well, which provide some churn in the diffstat. Other major thing is the typec code that moved out of staging and into the "real" part of the drivers/usb/ tree, which was nice to see happen. All of these have been in linux-next with no reported issues for a while" * tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits) usb: gadget: f_fs: Fix use-after-free in ffs_free_inst USB: usbfs: compute urb->actual_length for isochronous usb: core: message: remember to reset 'ret' to 0 when necessary USB: typec: Remove remaining redundant license text USB: typec: add SPDX identifiers to some files USB: renesas_usbhs: rcar?.h: add SPDX tags USB: chipidea: ci_hdrc_tegra.c: add SPDX line USB: host: xhci-debugfs: add SPDX lines USB: add SPDX identifiers to all remaining Makefiles usb: host: isp1362-hcd: remove a couple of redundant assignments USB: adutux: remove redundant variable minor usb: core: add a new usb_get_ptm_status() helper usb: core: add a 'type' parameter to usb_get_status() usb: core: introduce a new usb_get_std_status() helper usb: core: rename usb_get_status() 'type' argument to 'recip' usb: core: add Status Type definitions USB: gadget: Remove redundant license text USB: gadget: function: Remove redundant license text USB: gadget: udc: Remove redundant license text USB: gadget: legacy: Remove redundant license text ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

Merge tag 'extcon-next-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-next

2017-10-27T10:36:06Z

Chanwoo writes: Update extcon for 4.15 Detailed description for this pull request: 1. Split out extcon header file for consumer and provider device : The extcon has two type of extcon devices as following. - 'extcon provider deivce' adds new extcon device and detect the state/properties of external connector. Also, it notifies the state/properties to the extcon consumer device. - 'extcon consumer device' gets the change state/properties from extcon provider device. Prior to that, include/linux/extcon.h contains all exported API for both provider and consumer device driver. To clarify the meaning of header file and to remove the wrong use-case on consumer device. - include/linux/extcon-provider.h includes API for the provider device driver. - include/linux/extcon.h includes the API for the consumer device driver. 2. Support the SmartDock accessory on extcon-max77843.c device driver - Support the SmartDock accessory which detects following connectors at the same time. : USB host throught USB hub for mouse, keyboard and so on. : MHL connector for video output. : Charger connector for battery charging. - It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock. 3. Fix the minor issue of extcon driver - Delete the unneeded initialization in extcon-max14577. - Make extcon_info static const in order to fix the warning.

drivers: phy: add calibrate method

2017-10-23T05:49:28Z

Some quirky UDCs (like dwc3 on Exynos) need to have their phys calibrated e.g. for using super speed. This patch adds a new phy_calibrate() method. When the calibration should be used is dependent on actual chip. In case of dwc3 on Exynos the calibration must happen after usb_add_hcd() (while in host mode), because certain phy parameters like Tx LOS levels and boost levels need to be calibrated further post initialization of xHCI controller, to get SuperSpeed operations working. But an hcd must be prepared first in order to pass it to usb_add_hcd(), so, in particular, dwc3 registers must be available first, and in order for the latter to happen the phys must be initialized. This poses a chicken and egg problem if the calibration were to be performed in phy_init(). To break the circular dependency a separate method is added which can be called at a desired moment after phy intialization. Signed-off-by: Andrzej Pietrasiewicz Signed-off-by: Kishon Vijay Abraham I

ufs/phy: qcom: Refactor to use phy_init call

2017-10-23T05:49:27Z

Refactor ufs_qcom_power_up_sequence() to get rid of ugly exported phy APIs and use the phy_init() and phy_power_on() to do the phy initialization. Signed-off-by: Vivek Gautam Reviewed-by: Subhash Jadavani Signed-off-by: Kishon Vijay Abraham I