linux/drivers/regulator, branch v4.6

Merge remote-tracking branches 'regulator/fix/axp20x', 'regulator/fix/da9063', 'regulator/fix/gpio' and 'regulator/fix/s2mps11' into regulator-linus

2016-05-13T10:11:08Z

regulator: da9063: Correct module alias prefix to fix module autoloading

2016-05-10T19:00:49Z

s/paltform/platform/ Signed-off-by: Geert Uytterhoeven Signed-off-by: Mark Brown

regulator: axp20x: Fix axp22x ldo_io registration error on cold boot

2016-04-29T10:43:50Z

The maximum supported voltage for ldo_io# is 3.3V, but on cold boot the selector comes up at 0x1f, which maps to 3.8V. This causes _regulator_get_voltage() to fail with -EINVAL which causes regulator registration to fail when constrains are used: [ 1.467788] vcc-touchscreen: failed to get the current voltage(-22) [ 1.474209] axp20x-regulator axp20x-regulator: Failed to register ldo_io1 [ 1.483363] axp20x-regulator: probe of axp20x-regulator failed with error -22 This commits makes the axp20x regulator driver accept the 0x1f register value, fixing this. The datasheet does not guarantee reliable operation above 3.3V, so on boards where this regulator is used the regulator-max-microvolt setting must be 3.3V or less. Signed-off-by: Hans de Goede Signed-off-by: Mark Brown

regulator: axp20x: Fix axp22x ldo_io voltage ranges

2016-04-27T15:14:52Z

The minium voltage of 1800mV is a copy and paste error from the axp20x regulator info. The correct minimum voltage for the ldo_io regulators on the axp22x is 700mV. Fixes: 1b82b4e4f954 ("regulator: axp20x: Add support for AXP22X regulators") Signed-off-by: Hans de Goede Acked-by: Chen-Yu Tsai Signed-off-by: Mark Brown

regulator: axp20x: Fix LDO4 linear voltage range

2016-04-26T14:57:45Z

The current linear voltage range for the LDO4 regulator found in the APX20X PMICs assumes that the voltage is linear between 2.5 and 3.1V. However, the PMIC can output up to 3.3V on that regulator by skipping the 2.6V and 2.9V steps. Fix the ranges to read and set the proper voltages. Fixes: 13d57e64352a ("regulator: axp20x: Use linear voltage ranges for AXP20X LDO4") Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Signed-off-by: Mark Brown

regulator: s2mps11: Fix invalid selector mask and voltages for buck9

2016-03-28T09:36:30Z

The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff instead of 0x1f) thus reading entire register as buck9's voltage. This effectively caused regulator core to interpret values as higher voltages than they were and then to set real voltage much lower than intended. The buck9 provides power to other regulators, including LDO13 and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower voltage caused SD card detection errors on Odroid XU3/XU4: mmc1: card never left busy state mmc1: error -110 whilst initialising SD card During driver probe the regulator core was checking whether initial voltage matches the constraints. With incorrect vsel_mask of 0xff and default value of 0x50, the core interpreted this as 5 V which is outside of constraints (3-3.775 V). Then the regulator core was adjusting the voltage to match the constraints. With incorrect vsel_mask this new voltage mapped to a vere low voltage in the driver. Signed-off-by: Krzysztof Kozlowski Reviewed-by: Javier Martinez Canillas Tested-by: Javier Martinez Canillas Signed-off-by: Mark Brown Cc:

Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

2016-03-18T17:15:11Z

Pull MFD updates from Lee Jones: "New Drivers: - Freescale Touch Screen ADC - X-Powers AXP PMIC with RSB - TI TPS65086 Power Management IC (PMIC) New Device Support: - Supply device PCI IDs for Intel Broxton Fix-ups: - Move to clkdev_create() API; intel_quark_i2c_gpio - Complete re-write of TI's TPS65912 Power Management IC (PMIC) - Remove unnecessary function argument; axp20x - Separate out bus related code; axp20x - Coding Style changes; axp20x - Allow more drivers to be compiled as modules - Work around false positive 'used uninitialised' warning; db8500-prcmu Bug Fixes: - Remove do_div(); fsl-imx25-gcq - Fix driver init when built-in; tps65010 - Fix clock-unregister leak; intel-lpss" * tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits) mfd: intel-lpss: Pass I2C configuration via properties on BXT mfd: imx6sx: Add PCIe register definitions for iomuxc gpr mfd: ipaq-micro: Use __maybe_unused to hide pm functions mfd: max77686: Add max77802 to I2C device ID table mfd: max77686: Export OF module alias information mfd: max77686: Allow driver to be built as a module mfd: stmpe: Add the proper PWM resources mfd: tps65090: Set regmap config reg counts properly mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled mfd: as3711: Set regmap config reg counts properly mfd: rc5t583: Set regmap config reg counts properly gpio: tps65086: Add GPO driver for the TPS65086 PMIC mfd: mt6397: Add platform device ID table mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists mfd: mt6397: Add MT6323 support to MT6397 driver mfd: mt6397: Add support for different Slave types mfd: mt6397: int_con and int_status may vary in location dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists mfd: Add documentation for ACT8945A DT bindings ...

Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

2016-03-18T04:05:32Z

Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for kernel v4.6. There is quite a lot of interesting stuff going on. The patches to other subsystems and arch-wide are ACKed as far as possible, though I consider things like per-arch as essentially a part of the GPIO subsystem so it should not be needed. Core changes: - The gpio_chip is now a *real device*. Until now the gpio chips were just piggybacking the parent device or (gasp) floating in space outside of the device model. We now finally make GPIO chips devices. The gpio_chip will create a gpio_device which contains a struct device, and this gpio_device struct is kept private. Anything that needs to be kept private from the rest of the kernel will gradually be moved over to the gpio_device. - As a result of making the gpio_device a real device, we have added resource management, so devm_gpiochip_add_data() will cut down on overhead and reduce code lines. A huge slew of patches convert almost all drivers in the subsystem to use this. - Building on making the GPIO a real device, we add the first step of a new userspace ABI: the GPIO character device. We take small steps here, so we first add a pure *information* ABI and the tool "lsgpio" that will list all GPIO devices on the system and all lines on these devices. We can now discover GPIOs properly from userspace. We still have not come up with a way to actually *use* GPIOs from userspace. - To encourage people to use the character device for the future, we have it always-enabled when using GPIO. The old sysfs ABI is still opt-in (and can be used in parallel), but is marked as deprecated. We will keep it around for the foreseeable future, but it will not be extended to cover ever more use cases. Cleanup: - Bjorn Helgaas removed a whole slew of per-architecture includes. This dates back to when GPIO was an opt-in feature and no shared library even existed: just a header file with proper prototypes was provided and all semantics were up to the arch to implement. These patches make the GPIO chip even more a proper device and cleans out leftovers of the old in-kernel API here and there. Still some cruft is left but it's very little now. - There is still some clamping of return values for .get() going on, but we now return sane values in the vast majority of drivers and the errorpath is sanitized. Some patches for powerpc, blackfin and unicore still drop in. - We continue to switch the ARM, MIPS, blackfin, m68k local GPIO implementations to use gpiochip_add_data() and cut down on code lines. - MPC8xxx is converted to use the generic GPIO helpers. - ATH79 is converted to use the generic GPIO helpers. New drivers: - WinSystems WS16C48 - Acces 104-DIO-48E - F81866 (a F7188x variant) - Qoric (a MPC8xxx variant) - TS-4800 - SPI serializers (pisosr): simple 74xx shift registers connected to SPI to obtain a dirt-cheap output-only GPIO expander. - Texas Instruments TPIC2810 - Texas Instruments TPS65218 - Texas Instruments TPS65912 - X-Gene (ARM64) standby GPIO controller" * tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits) Revert "Share upstreaming patches" gpio: mcp23s08: Fix clearing of interrupt. gpiolib: Fix comment referring to gpio_*() in gpiod_*() gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit gpio: xgene: Fix kconfig for standby GIPO contoller gpio: Add generic serializer DT binding gpio: uapi: use 0xB4 as ioctl() major gpio: tps65912: fix bad merge Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free" gpio: omap: drop dev field from gpio_bank structure gpio: mpc8xxx: Slightly update the code for better readability gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip gpio: mpc8xxx: Fixup setting gpio direction output gpio: mcp23s08: Add support for mcp23s18 dt-bindings: gpio: altera: Fix altr,interrupt-type property gpio: add driver for MEN 16Z127 GPIO controller gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free gpio: timberdale: Switch to devm_ioremap_resource() gpio: ts4800: Add IMX51 dependency gpiolib: rewrite gpiodev_add_to_list ...

regulator: gpio: check return value of of_get_named_gpio

2016-03-17T11:44:57Z

At boot time the regulator driver can be initialized before the gpio, in which case the call to of_get_named_gpio will return EPROBE_DEFER. This value is silently passed to regulator_register which will return success, although the gpio is not registered (regulator_ena_gpio_request not called) as the value passed is detected as invalid. The gpio_regulator_probe will therefore succeed win no gpio requested. Signed-off-by: Mihai Mihalache Reviewed-by: Hans Holmberg Signed-off-by: Mark Brown

Merge remote-tracking branches 'regulator/topic/s5m8767' and 'regulator/topic/vexpress' into regulator-next

2016-03-13T08:20:14Z