linux/drivers/tty/serial, branch v3.17

tty: xuartps: Fix tx_emtpy() callback

2014-09-08T23:33:56Z

The tx_empty() callback currently checks the TXEMPTY bit in the interrupt status register to decided whether the FIFO should be reported as empty or not. The bit in this register gets set when the FIFO state transitions from non-empty to empty but is cleared again in the interrupt handler. This means it is not suitable to be used to decided whether the FIFO is currently empty or not. Instead use the TXEMPTY bit from the status register which will be set as long as the FIFO is empty. Signed-off-by: Lars-Peter Clausen Acked-by: Soren Brinkmann Signed-off-by: Greg Kroah-Hartman

tty/serial: at91: BUG: disable interrupts when !UART_ENABLE_MS()

2014-09-08T23:33:56Z

In set_termios(), interrupts where not disabled if UART_ENABLE_MS() was false. Tested on at91sam9g35. Signed-off-by: Richard Genoud Cc: stable # >= 3.16 Reviewed-by: Peter Hurley Acked-by: Nicolas Ferre Signed-off-by: Greg Kroah-Hartman

serial: 8250_dw: Add ACPI ID for Intel Braswell

2014-09-08T23:33:56Z

Another new ACPI identifier for the 8250 dw bindings to cover newer Intel SoCs such as Braswell. Signed-off-by: Alan Cox Signed-off-by: Mika Westerberg Signed-off-by: Greg Kroah-Hartman

Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux

2014-08-14T15:53:39Z

Pull device tree updates from Grant Likely: "The branch contains the following device tree changes the v3.17 merge window: Group changes to the device tree. In preparation for adding device tree overlay support, OF_DYNAMIC is reworked so that a set of device tree changes can be prepared and applied to the tree all at once. OF_RECONFIG notifiers see the most significant change here so that users always get a consistent view of the tree. Notifiers generation is moved from before a change to after it, and notifiers for a group of changes are emitted after the entire block of changes have been applied Automatic console selection from DT. Console drivers can now use of_console_check() to see if the device node is specified as a console device. If so then it gets added as a preferred console. UART devices get this support automatically when uart_add_one_port() is called. DT unit tests no longer depend on pre-loaded data in the device tree. Data is loaded dynamically at the start of unit tests, and then unloaded again when the tests have completed. Also contains a few bugfixes for reserved regions and early memory setup" * tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits) of: Fixing OF Selftest build error drivers: of: add automated assignment of reserved regions to client devices of: Use proper types for checking memory overflow of: typo fix in __of_prop_dup() Adding selftest testdata dynamically into live tree of: Add todo tasklist for Devicetree of: Transactional DT support. of: Reorder device tree changes and notifiers of: Move dynamic node fixups out of powerpc and into common code of: Make sure attached nodes don't carry along extra children of: Make devicetree sysfs update functions consistent. of: Create unlocked versions of node and property add/remove functions OF: Utility helper functions for dynamic nodes of: Move CONFIG_OF_DYNAMIC code into a separate file of: rename of_aliases_mutex to just of_mutex of/platform: Fix of_platform_device_destroy iteration of devices of: Migrate of_find_node_by_name() users to for_each_node_by_name() tty: Update hypervisor tty drivers to use core stdout parsing code. arm/versatile: Add the uart as the stdout device. of: Enable console on serial ports specified by /chosen/stdout-path ...

Merge branch 'devicetree/next-console' into devicetree/next

2014-08-11T13:03:08Z

Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

2014-08-08T18:14:29Z

Pull ARM SoC platform changes from Olof Johansson: "This is the bulk of new SoC enablement and other platform changes for 3.17: - Samsung S5PV210 has been converted to DT and multiplatform - Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms - Kirkwood, one of the popular Marvell platforms, is folded into the mvebu platform code, removing mach-kirkwood - Hwmod data for TI AM43xx and DRA7 platforms - More additions of Renesas shmobile platform support - Removal of plat-samsung contents that can be removed with S5PV210 being multiplatform/DT-enabled and the other two old platforms being removed New platforms (most with only basic support right now): - Hisilicon X5HD2 settop box chipset is introduced - Mediatek MT6589 (mobile chipset) is introduced - Broadcom BCM7xxx settop box chipset is introduced + as usual a lot other pieces all over the platform code" * tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits) ARM: hisi: remove smp from machine descriptor power: reset: move hisilicon reboot code ARM: dts: Add hix5hd2-dkb dts file. ARM: debug: Rename Hi3716 to HIX5HD2 ARM: hisi: enable hix5hd2 SoC ARM: hisi: add ARCH_HISI MAINTAINERS: add entry for Broadcom ARM STB architecture ARM: brcmstb: select GISB arbiter and interrupt drivers ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs ARM: configs: enable SMP in bcm_defconfig ARM: add SMP support for Broadcom mobile SoCs Documentation: arm: misc updates to Marvell EBU SoC status Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC ARM: mvebu: fix build without platforms selected ARM: mvebu: add cpuidle support for Armada 38x ARM: mvebu: add cpuidle support for Armada 370 cpuidle: mvebu: add Armada 38x support cpuidle: mvebu: add Armada 370 support cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7 ARM: mvebu: export the SCU address ...

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next

2014-08-06T16:41:23Z

Pull sparc updates from David Miller: 1) Add sparc RAM output to /proc/iomem, from Bob Picco. 2) Allow seeks on /dev/mdesc, from Khalid Aziz. 3) Cleanup sparc64 I/O accessors, from Sam Ravnborg. 4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do not insert it into the TLB miss hash tables otherwise we'll livelock. Based upon work by Christopher Alexander Tobias Schulze. 5) Fix BREAK detection in sunsab driver when no actual characters are pending, from Christopher Alexander Tobias Schulze. 6) Because we have modules --> openfirmware --> vmalloc ordering of virtual memory, the lazy VMAP TLB flusher can cons up an invocation of flush_tlb_kernel_range() that covers the openfirmware address range. Unfortunately this will flush out the firmware's locked TLB mapping which causes all kinds of trouble. Just split up the flush request if this happens, but in the long term the lazy VMAP flusher should probably be made a little bit smarter. Based upon work by Christopher Alexander Tobias Schulze. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next: sparc64: Fix up merge thinko. sparc: Add "install" target arch/sparc/math-emu/math_32.c: drop stray break operator sparc64: ldc_connect() should not return EINVAL when handshake is in progress. sparc64: Guard against flushing openfirmware mappings. sunsab: Fix detection of BREAK on sunsab serial console bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000 sparc64: Do not insert non-valid PTEs into the TSB hash table. sparc64: avoid code duplication in io_64.h sparc64: reorder functions in io_64.h sparc64: drop unused SLOW_DOWN_IO definitions sparc64: remove macro indirection in io_64.h sparc64: update IO access functions in PeeCeeI sparcspkr: use sbus_*() primitives for IO sparc: Add support for seek and shorter read to /dev/mdesc sparc: use %s for unaligned panic drivers/sbus/char: Micro-optimization in display7seg.c display7seg: Introduce the use of the managed version of kzalloc sparc64 - add mem to iomem resource

sunsab: Fix detection of BREAK on sunsab serial console

2014-08-05T00:01:49Z

Fix detection of BREAK on sunsab serial console: BREAK detection was only performed when there were also serial characters received simultaneously. To handle all BREAKs correctly, the check for BREAK and the corresponding call to uart_handle_break() must also be done if count == 0, therefore duplicate this code fragment and pull it out of the loop over the received characters. Patch applies to 3.16-rc6. Signed-off-by: Christopher Alexander Tobias Schulze Signed-off-by: David S. Miller

pch_uart: don't hardcode PCI slot to get DMA device

2014-08-01T23:04:21Z

The DMA is a function 0 of the multifunction device where SPI host is attached. Thus, we may avoid to hardcode PCI slot number. Signed-off-by: Andy Shevchenko Signed-off-by: Greg Kroah-Hartman

serial: sc16is7xx: Correct initialization of s->clk

2014-07-27T18:50:38Z

The s->clk never gets setup in sc16is7xx_probe() and instead was using a local clk variable, but then testing the uninitialized s->clk during teardown Reported-by: Dan Carpenter Signed-off-by: Jon Ringle Signed-off-by: Greg Kroah-Hartman