linux/drivers/tty, branch v4.20

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc

2018-12-21T22:23:57Z

Pull sparc fixes from David Miller: "Just some small fixes here and there, and a refcount leak in a serial driver, nothing serious" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: serial/sunsu: fix refcount leak sparc: Set "ARCH: sunxx" information on the same line sparc: vdso: Drop implicit common-page-size linker flag

serial/sunsu: fix refcount leak

2018-12-21T19:24:38Z

The function of_find_node_by_path() acquires a reference to the node returned by it and that reference needs to be dropped by its caller. su_get_type() doesn't do that. The match node are used as an identifier to compare against the current node, so we can directly drop the refcount after getting the node from the path as it is not used as pointer. Fix this by use a single variable and drop the refcount right after of_find_node_by_path(). Signed-off-by: Yangtao Li Signed-off-by: David S. Miller

Revert "serial: 8250: Fix clearing FIFOs in RS485 mode again"

2018-12-17T15:18:29Z

Commit f6aa5beb45be ("serial: 8250: Fix clearing FIFOs in RS485 mode again") makes a change to FIFO clearing code which its commit message suggests was intended to be specific to use with RS485 mode, however: 1) The change made does not just affect __do_stop_tx_rs485(), it also affects other uses of serial8250_clear_fifos() including paths for starting up, shutting down or auto-configuring a port regardless of whether it's an RS485 port or not. 2) It makes the assumption that resetting the FIFOs is a no-op when FIFOs are disabled, and as such it checks for this case & explicitly avoids setting the FIFO reset bits when the FIFO enable bit is clear. A reading of the PC16550D manual would suggest that this is OK since the FIFO should automatically be reset if it is later enabled, but we support many 16550-compatible devices and have never required this auto-reset behaviour for at least the whole git era. Starting to rely on it now seems risky, offers no benefit, and indeed breaks at least the Ingenic JZ4780's UARTs which reads garbage when the RX FIFO is enabled if we don't explicitly reset it. 3) By only resetting the FIFOs if they're enabled, the behaviour of serial8250_do_startup() during boot now depends on what the value of FCR is before the 8250 driver is probed. This in itself seems questionable and leaves us with FCR=0 & no FIFO reset if the UART was used by 8250_early, otherwise it depends upon what the bootloader left behind. 4) Although the naming of serial8250_clear_fifos() may be unclear, it is clear that callers of it expect that it will disable FIFOs. Both serial8250_do_startup() & serial8250_do_shutdown() contain comments to that effect, and other callers explicitly re-enable the FIFOs after calling serial8250_clear_fifos(). The premise of that patch that disabling the FIFOs is incorrect therefore seems wrong. For these reasons, this reverts commit f6aa5beb45be ("serial: 8250: Fix clearing FIFOs in RS485 mode again"). Signed-off-by: Paul Burton Fixes: f6aa5beb45be ("serial: 8250: Fix clearing FIFOs in RS485 mode again"). Cc: Greg Kroah-Hartman Cc: Daniel Jedrychowski Cc: Marek Vasut Cc: linux-mips@vger.kernel.org Cc: linux-serial@vger.kernel.org Cc: stable # 4.10+ Signed-off-by: Greg Kroah-Hartman

Merge tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2018-12-09T18:24:29Z

Pull tty driver fixes from Greg KH: "Here are three small tty driver fixes for 4.20-rc6 Nothing major, just some bug fixes for reported issues. Full details are in the shortlog. All of these have been in linux-next for a while with no reported issues" * tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var() tty: serial: 8250_mtk: always resume the device in probe. tty: do not set TTY_IO_ERROR flag if console port

Merge tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2018-12-09T18:18:24Z

Pull USB fixes from Greg KH: "Here are some small USB fixes for 4.20-rc6 The "largest" here are some xhci fixes for reported issues. Also here is a USB core fix, some quirk additions, and a usb-serial fix which required the export of one of the tty layer's functions to prevent code duplication. The tty maintainer agreed with this change. All of these have been in linux-next with no reported issues" * tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: xhci: Prevent U1/U2 link pm states if exit latency is too long xhci: workaround CSS timeout on AMD SNPS 3.0 xHC USB: check usb_get_extra_descriptor for proper size USB: serial: console: fix reported terminal settings usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device USB: Fix invalid-free bug in port_over_current_notify() usb: appledisplay: Add 27" Apple Cinema Display

kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var()

2018-12-06T14:59:07Z

This patch is trying to fix KE issue due to "BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198" reported by Syzkaller scan." [26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198 [26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364 [26364:syz-executor0][name:report&] [26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0 [26364:syz-executor0]Call trace: [26364:syz-executor0][] dump_bacIctrace+Ox0/0x470 [26364:syz-executor0][] show_stack+0x20/0x30 [26364:syz-executor0][] dump_stack+Oxd8/0x128 [26364:syz-executor0][] print_address_description +0x80/0x4a8 [26364:syz-executor0][] kasan_report+Ox178/0x390 [26364:syz-executor0][] _asan_report_loadi_noabort+Ox18/0x20 [26364:syz-executor0][] param_set_kgdboc_var+Ox194/0x198 [26364:syz-executor0][] param_attr_store+Ox14c/0x270 [26364:syz-executor0][] module_attr_store+0x60/0x90 [26364:syz-executor0][] sysfs_kl_write+Ox100/0x158 [26364:syz-executor0][] kernfs_fop_write+0x27c/0x3a8 [26364:syz-executor0][] do_loop_readv_writev+0x114/0x1b0 [26364:syz-executor0][] do_readv_writev+0x4f8/0x5e0 [26364:syz-executor0][] vfs_writev+0x7c/Oxb8 [26364:syz-executor0][] SyS_writev+Oxcc/0x208 [26364:syz-executor0][] elO_svc_naked +0x24/0x28 [26364:syz-executor0][name:report&] [26364:syz-executor0][name:report&]The buggy address belongs to the variable: [26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40 [26364:syz-executor0][name:report&] [26364:syz-executor0][name:report&]Memory state around the buggy address: [26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa [26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa [26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00 [26364:syz-executor0][name:report&] ^ [26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa [26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa [26364:syz-executor0][name:report&] [26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint [26364:syz-executor0]------------[cut here]------------ After checking the source code, we've found there might be an out-of-bounds access to "config[len - 1]" array when the variable "len" is zero. Signed-off-by: Macpaul Lin Acked-by: Daniel Thompson Cc: stable Signed-off-by: Greg Kroah-Hartman

tty: serial: 8250_mtk: always resume the device in probe.

2018-12-05T10:31:21Z

serial8250_register_8250_port calls uart_config_port, which calls config_port on the port before it tries to power on the port. So we need the port to be on before calling serial8250_register_8250_port. Change the code to always do a runtime resume in probe before registering port, and always do a runtime suspend in remove. This basically reverts the change in commit 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling"), but still use pm_runtime callbacks. Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling") Signed-off-by: Peter Shih Cc: stable Signed-off-by: Greg Kroah-Hartman

USB: serial: console: fix reported terminal settings

2018-12-05T10:29:10Z

The USB-serial console implementation has never reported the actual terminal settings used. Despite storing the corresponding cflags in its struct console, these were never honoured on later tty open() where the tty termios would be left initialised to the driver defaults. Unlike the serial console implementation, the USB-serial code calls subdriver open() already at console setup. While calling set_termios() and write() before open() looks like it could work for some USB-serial drivers, others definitely do not expect this, so modelling this after serial core is going to be intrusive, if at all possible. Instead, use a (renamed) tty helper to save the termios data used at console setup so that the tty termios reflects the actual terminal settings after a subsequent tty open(). Note that the calls to tty_init_termios() (tty_driver_install()) and tty_save_termios() are serialised using the disconnect mutex. This specifically fixes a regression that was triggered by a recent change adding software flow control to the pl2303 driver: a getty trying to disable flow control while leaving the baud rate unchanged would now also set the baud rate to the driver default (prior to the flow-control change this had been a noop). Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control") Cc: stable # 4.18 Cc: Florian Zumbiehl Reported-by: Jarkko Nikula Tested-by: Jarkko Nikula Acked-by: Greg Kroah-Hartman Signed-off-by: Johan Hovold

drivers/tty: add missing of_node_put()

2018-12-03T04:55:23Z

of_find_node_by_path() acquires a reference to the node returned by it and that reference needs to be dropped by its caller. This place is not doing this, so fix it. Signed-off-by: Yangtao Li Signed-off-by: David S. Miller

tty: do not set TTY_IO_ERROR flag if console port

2018-11-27T08:58:11Z

Since Commit 761ed4a94582 ('tty: serial_core: convert uart_close to use tty_port_close') and Commit 4dda864d7307 ('tty: serial_core: Fix serial console crash on port shutdown), a serial port which is used as console can be stuck when logging out if there is a remained process. After logged out, agetty will try to grab the serial port but it will be failed because the previous process did not release the port correctly. To fix this, TTY_IO_ERROR bit should not be enabled of tty_port_close if the port is console port. Reproduce step: - Run background processes from serial console $ while true; do sleep 10; done & - Log out $ logout -> Stuck - Read journal log by journalctl | tail Jan 28 16:07:01 ubuntu systemd[1]: Stopped Serial Getty on ttyAMA0. Jan 28 16:07:01 ubuntu systemd[1]: Started Serial Getty on ttyAMA0. Jan 28 16:07:02 ubuntu agetty[1643]: /dev/ttyAMA0: not a tty Fixes: 761ed4a94582 ("tty: serial_core: convert uart_close to use tty_port_close") Cc: Geert Uytterhoeven Cc: Rob Herring Cc: Jiri Slaby Signed-off-by: Chanho Park Cc: stable Signed-off-by: Greg Kroah-Hartman