linux/drivers/tty, branch v5.1

sc16is7xx: put err_spi and err_i2c into correct #ifdef

2019-04-19T12:09:23Z

err_spi is only called within SERIAL_SC16IS7XX_SPI while err_i2c is called inside SERIAL_SC16IS7XX_I2C. So we need to put err_spi and err_i2c into each #ifdef accordingly. This change fixes ("sc16is7xx: move label 'err_spi' to correct section"). Signed-off-by: Guoqing Jiang Signed-off-by: Greg Kroah-Hartman

vt: fix cursor when clearing the screen

2019-04-17T12:45:15Z

The patch a6dbe4427559 ("vt: perform safe console erase in the right order") introduced a bug. The conditional do_update_region() was replaced by a call to update_region() that does contain the conditional already, but with unwanted extra side effects such as restoring the cursor drawing. In order to reproduce the bug: - use framebuffer console with the AMDGPU driver - type "links" to start the console www browser - press 'q' and space to exit links Now the cursor will be permanently visible in the center of the screen. It will stay there until something overwrites it. The bug goes away if we change update_region() back to the conditional do_update_region(). [ nico: reworded changelog ] Signed-off-by: Mikulas Patocka Reviewed-by: Nicolas Pitre Cc: stable@vger.kernel.org Fixes: a6dbe4427559 ("vt: perform safe console erase in the right order") Signed-off-by: Greg Kroah-Hartman

sc16is7xx: move label 'err_spi' to correct section

2019-04-16T13:24:38Z

err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make the label only available under SERIAL_SC16IS7XX_SPI option. Otherwise, the below warning appears. drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label] err_spi: ^~~~~~~ Signed-off-by: Guoqing Jiang Fixes: ac0cdb3d9901 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()") Signed-off-by: Arnd Bergmann Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix HSCIF RX sampling point adjustment

2019-04-16T13:24:38Z

The calculation of the sampling point has min() and max() exchanged. Fix this by using the clamp() helper instead. Fixes: 63ba1e00f178a448 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment") Signed-off-by: Geert Uytterhoeven Reviewed-by: Ulrich Hecht Reviewed-by: Wolfram Sang Acked-by: Dirk Behme Cc: stable Reviewed-by: Simon Horman Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix HSCIF RX sampling point calculation

2019-04-16T13:24:38Z

There are several issues with the formula used for calculating the deviation from the intended rate: 1. While min_err and last_stop are signed, srr and baud are unsigned. Hence the signed values are promoted to unsigned, which will lead to a bogus value of deviation if min_err is negative, 2. Srr is the register field value, which is one less than the actual sampling rate factor, 3. The divisions do not use rounding. Fix this by casting unsigned variables to int, adding one to srr, and using a single DIV_ROUND_CLOSEST(). Fixes: 63ba1e00f178a448 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment") Signed-off-by: Geert Uytterhoeven Reviewed-by: Mukesh Ojha Cc: stable Reviewed-by: Ulrich Hecht Signed-off-by: Greg Kroah-Hartman

tty: fix NULL pointer issue when tty_port ops is not set

2019-03-27T16:21:21Z

Unlike 'client_ops' which is initialized to 'default_client_ops', the port operations 'ops' may be left to NULL. Check the 'ops' value before checking the 'ops->x' value. Signed-off-by: Fabien Dessenne Signed-off-by: Greg Kroah-Hartman

Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc

2019-03-27T15:27:48Z

Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such device” error. This is caused by function "configure_kgdboc" who init err to ENODEV when the config is empty (legal input) the code go out with ENODEV returned. Fixes: 2dd453168643 ("kgdboc: Fix restrict error") Signed-off-by: Wentao Wang Cc: stable Acked-by: Daniel Thompson Signed-off-by: Greg Kroah-Hartman

tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped

2019-03-27T15:27:48Z

In half-duplex operation, RX should be started after TX completes. If DMA is used, there is a case when the DMA transfer completes but the TX FIFO is not emptied, so the RX cannot be restarted just yet. Use a boolean variable to store this state and rearm TX interrupt mask to be signaled again that the transfer finished. In interrupt transmit handler this variable is used to start RX. A warning message is generated if RX is activated before TX fifo is cleared. Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done") Signed-off-by: Razvan Stefanescu Acked-by: Richard Genoud Cc: stable Signed-off-by: Greg Kroah-Hartman

tty/serial: atmel: Add is_half_duplex helper

2019-03-27T15:27:48Z

Use a helper function to check that a port needs to use half duplex communication, replacing several occurrences of multi-line bit checking. Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done") Cc: stable Signed-off-by: Razvan Stefanescu Acked-by: Richard Genoud Signed-off-by: Greg Kroah-Hartman

serial: sh-sci: Fix setting SCSCR_TIE while transferring data

2019-03-19T14:37:44Z

We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted (if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer, re-enable the SCSCR_TIE bit, which was done at sci_start_tx(). This is unnecessary processing, wasting CPU operation if the data transmission length is large. And further, transmit end, FIFO empty bits disabling have also been performed in the step above. Signed-off-by: Hoan Nguyen An Cc: stable Signed-off-by: Greg Kroah-Hartman