linux/drivers/tty, branch v6.8

Revert "tty: serial: simplify qcom_geni_serial_send_chunk_fifo()"

2024-03-05T13:40:34Z

This reverts commit 5c7e105cd156fc9adf5294a83623d7a40c15f9b9. As identified by KASAN, the simplification done by the cleanup patch was not legal. >From tracing through the code, it can be seen that we're transmitting from a 4096-byte circular buffer. We copy anywhere from 1-4 bytes from it each time. The simplification runs into trouble when we get near the end of the circular buffer. For instance, we might start out with xmit->tail = 4094 and we want to transfer 4 bytes. With the code before simplification this was no problem. We'd read buf[4094], buf[4095], buf[0], and buf[1]. With the new code we'll do a memcpy(&buf[4094], 4) which reads 2 bytes past the end of the buffer and then skips transmitting what's at buf[0] and buf[1]. KASAN isn't 100% consistent at reporting this for me, but to be extra confident in the analysis, I added traces of the tail and tx_bytes and then wrote a test program: while true; do echo -n "abcdefghijklmnopqrstuvwxyz0" > /dev/ttyMSM0 sleep .1 done I watched the traces over SSH and saw: qcom_geni_serial_send_chunk_fifo: 4093 4 qcom_geni_serial_send_chunk_fifo: 1 3 Which indicated that one byte should be missing. Sure enough the output that should have been: abcdefghijklmnopqrstuvwxyz0 In one case was actually missing a byte: abcdefghijklmnopqrstuvwyz0 Running "ls -al" on large directories also made the missing bytes obvious since columns didn't line up. While the original code may not be the most elegant, we only talking about copying up to 4 bytes here. Let's just go back to the code that worked. Fixes: 5c7e105cd156 ("tty: serial: simplify qcom_geni_serial_send_chunk_fifo()") Cc: stable Signed-off-by: Douglas Anderson Acked-by: Jiri Slaby Tested-by: Johan Hovold Link: https://lore.kernel.org/r/20240304174952.1.I920a314049b345efd1f69d708e7f74d2213d0b49@changeid Signed-off-by: Greg Kroah-Hartman

tty: serial: fsl_lpuart: avoid idle preamble pending if CTS is enabled

2024-03-05T13:40:07Z

If the remote uart device is not connected or not enabled after booting up, the CTS line is high by default. At this time, if we enable the flow control when opening the device(for example, using “stty -F /dev/ttyLP4 crtscts” command), there will be a pending idle preamble(first writing 0 and then writing 1 to UARTCTRL_TE will queue an idle preamble) that cannot be sent out, resulting in the uart port fail to close(waiting for TX empty), so the user space stty will have to wait for a long time or forever. This is an LPUART IP bug(idle preamble has higher priority than CTS), here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE, so that the idle preamble does not get stuck due to CTS is deasserted. Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support") Cc: stable Signed-off-by: Sherry Sun Reviewed-by: Alexander Sverdlin Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman

vt: fix unicode buffer corruption when deleting characters

2024-03-02T22:09:04Z

This is the same issue that was fixed for the VGA text buffer in commit 39cdb68c64d8 ("vt: fix memory overlapping when deleting chars in the buffer"). The cure is also the same i.e. replace memcpy() with memmove() due to the overlaping buffers. Signed-off-by: Nicolas Pitre Fixes: 81732c3b2fed ("tty vt: Fix line garbage in virtual console on command line edition") Cc: stable Link: https://lore.kernel.org/r/sn184on2-3p0q-0qrq-0218-895349s4753o@syhkavp.arg Signed-off-by: Greg Kroah-Hartman

serial: port: Don't suspend if the port is still busy

2024-03-02T21:11:58Z

We accidently met the issue that the bash prompt is not shown after the previous command done and until the next input if there's only one CPU (In our issue other CPUs are isolated by isolcpus=). Further analysis shows it's because the port entering runtime suspend even if there's still pending chars in the buffer and the pending chars will only be processed in next device resuming. We are using amba-pl011 and the problematic flow is like below: Bash kworker tty_write() file_tty_write() n_tty_write() uart_write() __uart_start() pm_runtime_get() // wakeup waker queue_work() pm_runtime_work() rpm_resume() status = RPM_RESUMING serial_port_runtime_resume() port->ops->start_tx() pl011_tx_chars() uart_write_wakeup() […] __uart_start() pm_runtime_get() < 0 // because runtime status = RPM_RESUMING // later data are not commit to the port driver status = RPM_ACTIVE rpm_idle() -> rpm_suspend() This patch tries to fix this by checking the port busy before entering runtime suspending. A runtime_suspend callback is added for the port driver. When entering runtime suspend the callback is invoked, if there's still pending chars in the buffer then flush the buffer. Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM") Cc: stable Reviewed-by: Tony Lindgren Reviewed-by: Andy Shevchenko Signed-off-by: Yicong Yang Link: https://lore.kernel.org/r/20240226152351.40924-1-yangyicong@huawei.com Signed-off-by: Greg Kroah-Hartman

serial: 8250_dw: Do not reclock if already at correct rate

2024-03-02T21:11:03Z

When userspace opens the console, we call set_termios() passing a termios with the console's configured baud rate. Currently this causes dw8250_set_termios() to disable and then re-enable the UART clock at the same frequency as it was originally. This can cause corruption of any concurrent console output. Fix it by skipping the reclocking if we are already at the correct rate. Signed-off-by: Peter Collingbourne Fixes: 4e26b134bd17 ("serial: 8250_dw: clock rate handling for all ACPI platforms") Cc: stable@vger.kernel.org Reviewed-by: Andy Shevchenko Link: https://lore.kernel.org/r/20240222192635.1050502-1-pcc@google.com Signed-off-by: Greg Kroah-Hartman

tty: serial: imx: Fix broken RS485

2024-03-02T21:10:35Z

When about to transmit the function imx_uart_start_tx is called and in some RS485 configurations this function will call imx_uart_stop_rx. The problem is that imx_uart_stop_rx will enable loopback in order to release the RS485 bus, but when loopback is enabled transmitted data will just be looped to RX. This patch fixes the above problem by not enabling loopback when about to transmit. This driver now works well when used for RS485 half duplex master configurations. Fixes: 79d0224f6bf2 ("tty: serial: imx: Handle RS485 DE signal active high") Cc: stable Signed-off-by: Rickard x Andersson Tested-by: Christoph Niedermaier Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com Signed-off-by: Greg Kroah-Hartman

serial: amba-pl011: Fix DMA transmission in RS485 mode

2024-02-19T08:43:37Z

When DMA is used in RS485 mode make sure that the UARTs tx section is enabled before the DMA buffers are queued for transmission. Cc: stable@vger.kernel.org Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support") Signed-off-by: Lino Sanfilippo Link: https://lore.kernel.org/r/20240216224709.9928-2-l.sanfilippo@kunbus.com Signed-off-by: Greg Kroah-Hartman

serial: stm32: do not always set SER_RS485_RX_DURING_TX if RS485 is enabled

2024-02-19T08:43:37Z

Before commit 07c30ea5861f ("serial: Do not hold the port lock when setting rx-during-tx GPIO") the SER_RS485_RX_DURING_TX flag was only set if the rx-during-tx mode was not controlled by a GPIO. Now the flag is set unconditionally when RS485 is enabled. This results in an incorrect setting if the rx-during-tx GPIO is not asserted. Fix this by setting the flag only if the rx-during-tx mode is not controlled by a GPIO and thus restore the correct behaviour. Cc: stable@vger.kernel.org # 6.6+ Fixes: 07c30ea5861f ("serial: Do not hold the port lock when setting rx-during-tx GPIO") Signed-off-by: Lino Sanfilippo Link: https://lore.kernel.org/r/20240216224709.9928-1-l.sanfilippo@kunbus.com Signed-off-by: Greg Kroah-Hartman

tty: hvc: Don't enable the RISC-V SBI console by default

2024-02-19T08:43:33Z

The new SBI console has the same problem as the old one: there's only one shared backing hardware and no synchronization, so the two drivers end up stepping on each other. This was the same issue the old SBI-0.1 console drivers had, but that was disabled by default when SBI-0.1 was. So just mark the new driver as nonportable. Reported-by: Emil Renner Berthing Fixes: 88ead68e764c ("tty: Add SBI debug console support to HVC SBI driver") Signed-off-by: Palmer Dabbelt Reviewed-by: Paul Walmsley Reviewed-by: Anup Patel Reviewed-by: Conor Dooley Link: https://lore.kernel.org/r/20240214153429.16484-2-palmer@rivosinc.com Signed-off-by: Greg Kroah-Hartman

serial: mxs-auart: fix tx

2024-02-06T14:42:11Z

Emil reports: After updating Linux on an i.MX28 board, serial communication over AUART broke. When I TX from the board and measure on the TX pin, it seems like the HW fifo is not emptied before the transmission is stopped. MXS performs weird things with stop_tx(). The driver makes it conditional on uart_tx_stopped(). So the driver needs special handling. Pass the brand new UART_TX_NOSTOP to uart_port_tx_flags() and handle the stop on its own. Signed-off-by: "Jiri Slaby (SUSE)" Reported-by: Emil Kronborg Cc: stable Fixes: 2d141e683e9a ("tty: serial: use uart_port_tx() helper") Closes: https://lore.kernel.org/all/miwgbnvy3hjpnricubg76ytpn7xoceehwahupy25bubbduu23s@om2lptpa26xw/ Tested-by: Stefan Wahren Tested-by: Emil Kronborg Link: https://lore.kernel.org/r/20240201105557.28043-2-jirislaby@kernel.org Signed-off-by: Greg Kroah-Hartman