linux/drivers/usb/core, branch v3.5

usb: Add support for root hub port status CAS

2012-07-02T19:51:24Z

The host controller port status register supports CAS (Cold Attach Status) bit. This bit could be set when USB3.0 device is connected when system is in Sx state. When the system wakes to S0 this port status with CAS bit is reported and this port can't be used by any device. When CAS bit is set the port should be reset by warm reset. This was not supported by xhci driver. The issue was found when pendrive was connected to suspended platform. The link state of "Compliance Mode" was reported together with CAS bit. This link state was also not supported by xhci and core/hub.c. The CAS bit is defined only for xhci root hub port and it is not supported on regular hubs. The link status is used to force warm reset on port. Make the USB core issue a warm reset when port is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver to report 'compliance mode' when the CAS is set. This force warm reset on the root hub port. This patch should be backported to stable kernels as old as 3.2, that contain the commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When hot reset for USB3 fails, try warm reset." Signed-off-by: Stanislaw Ledwon Signed-off-by: Sarah Sharp Acked-by: Andiry Xu Cc: stable@vger.kernel.org

USB: fix gathering of interface associations

2012-06-15T00:13:34Z

TEAC's UD-H01 (and probably other devices) have a gap in the interface number allocation of their descriptors: Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 220 bNumInterfaces 3 [...] Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 [...] Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 2 bInterfaceCount 2 bFunctionClass 1 Audio bFunctionSubClass 0 bFunctionProtocol 32 iFunction 4 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 [...] Once a configuration is selected, usb_set_configuration() walks the known interfaces of a given configuration and calls find_iad() on each of them to set the interface association pointer the interface is included in. The problem here is that the loop variable is taken for the interface number in the comparison logic that gathers the association. Which is fine as long as the descriptors are sane. In the case above, however, the logic gets out of sync and the interface association fields of all interfaces beyond the interface number gap are wrong. Fix this by passing the interface's bInterfaceNumber to find_iad() instead. Signed-off-by: Daniel Mack Reported-by: bEN Reported-by: Ivan Perrone Tested-by: ivan perrone Cc: stable Signed-off-by: Greg Kroah-Hartman

Merge tag 'for-usb-linus-2012-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

2012-06-14T00:23:12Z

xhci: Bug fixes for 3.5 Hi Greg, Here's five bug fixes for 3.5. They fix some memory leaks in the bandwidth calculation code, fix a couple bugs in the USB3 Link PM patchset, and make system suspend and resume work on platforms with the AsMedia ASM1042 xHCI host controller. Sarah Sharp

USB: Checking the wrong variable in usb_disable_lpm()

2012-06-13T23:37:21Z

We check "u1_params" instead of checking "u2_params". Signed-off-by: Dan Carpenter Signed-off-by: Sarah Sharp

USB: add NO_D3_DURING_SLEEP flag and revert 151b61284776be2

2012-06-13T20:11:39Z

This patch (as1558) fixes a problem affecting several ASUS computers: The machine crashes or corrupts memory when going into suspend if the ehci-hcd driver is bound to any controllers. Users have been forced to unbind or unload ehci-hcd before putting their systems to sleep. After extensive testing, it was determined that the machines don't like going into suspend when any EHCI controllers are in the PCI D3 power state. Presumably this is a firmware bug, but there's nothing we can do about it except to avoid putting the controllers in D3 during system sleep. The patch adds a new flag to indicate whether the problem is present, and avoids changing the controller's power state if the flag is set. Runtime suspend is unaffected; this matters only for system suspend. However as a side effect, the controller will not respond to remote wakeup requests while the system is asleep. Hence USB wakeup is not functional -- but of course, this is already true in the current state of affairs. A similar patch has already been applied as commit 151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during suspend on ASUS computers). The patch supersedes that one and reverts it. There are two differences: The old patch added the flag at the USB level; this patch adds it at the PCI level. The old patch applied to all chipsets with the same vendor, subsystem vendor, and product IDs; this patch makes an exception for a known-good system (based on DMI information). Signed-off-by: Alan Stern Tested-by: Dâniel Fraga Tested-by: Andrey Rahmatullin Tested-by: Steven Rostedt Cc: stable Reviewed-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman

Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

2012-05-22T23:02:13Z

Pull driver core updates from Greg Kroah-Hartman: "Here's the driver core, and other driver subsystems, pull request for the 3.5-rc1 merge window. Outside of a few minor driver core changes, we ended up with the following different subsystem and core changes as well, due to interdependancies on the driver core: - hyperv driver updates - drivers/memory being created and some drivers moved into it - extcon driver subsystem created out of the old Android staging switch driver code - dynamic debug updates - printk rework, and /dev/kmsg changes All of this has been tested in the linux-next releases for a few weeks with no reported problems. Signed-off-by: Greg Kroah-Hartman " Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed that a patch to the deleted drivers/misc/max8997-muic.c driver needs to be applied to this one. * tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits) uio_pdrv_genirq: get irq through platform resource if not set otherwise memory: tegra{20,30}-mc: Remove empty *_remove() printk() - isolate KERN_CONT users from ordinary complete lines sysfs: get rid of some lockdep false positives Drivers: hv: util: Properly handle version negotiations. Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp() memory: tegra{20,30}-mc: Use dev_err_ratelimited() driver core: Add dev_*_ratelimited() family Driver Core: don't oops with unregistered driver in driver_find_device() printk() - restore prefix/timestamp printing for multi-newline strings printk: add stub for prepend_timestamp() ARM: tegra30: Make MC optional in Kconfig ARM: tegra20: Make MC optional in Kconfig ARM: tegra30: MC: Remove unnecessary BUG*() ARM: tegra20: MC: Remove unnecessary BUG*() printk: correctly align __log_buf ARM: tegra30: Add Tegra Memory Controller(MC) driver ARM: tegra20: Add Tegra Memory Controller(MC) driver printk() - restore timestamp printing at console output printk() - do not merge continuation lines of different threads ...

USB: Fix core compile with CONFIG_USB_SUSPEND=n

2012-05-21T16:00:03Z

When CONFIG_PM=n, make sure that the usb_[unlocked_][en/dis]able_lpm declarations are visible in include/linux/usb.h, and exported from drivers/usb/core/hub.c. Before this patch, if CONFIG_USB_SUSPEND was turned off, it would cause build errors: drivers/usb/core/hub.c: In function 'usb_disable_lpm': drivers/usb/core/hub.c:3394:2: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/hub.c: At top level: drivers/usb/core/hub.c:3424:6: warning: conflicting types for 'usb_enable_lpm' [enabled by default] drivers/usb/core/hub.c:3394:2: note: previous implicit declaration of 'usb_enable_lpm' was here drivers/usb/core/driver.c: In function 'usb_probe_interface': drivers/usb/core/driver.c:339:2: error: implicit declaration of function 'usb_unlocked_disable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/driver.c:364:3: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/message.c: In function 'usb_set_interface': drivers/usb/core/message.c:1314:2: error: implicit declaration of function 'usb_disable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/message.c:1323:3: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration] drivers/usb/core/message.c:1368:2: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration] Signed-off-by: Sarah Sharp Reported-by: Stephen Rothwell Reported-by: Chen Peter-B29397

USB: Remove races in devio.c

2012-05-18T23:37:55Z

There exist races in devio.c, below is one case, and there are similar races in destroy_async() and proc_unlinkurb(). Remove these races. cancel_bulk_urbs() async_completed() ------------------- ----------------------- spin_unlock(&ps->lock); list_move_tail(&as->asynclist, &ps->async_completed); wake_up(&ps->wait); Lead to free_async() be triggered, then urb and 'as' will be freed. usb_unlink_urb(as->urb); ===> refer to the freed 'as' Signed-off-by: Huajun Li Cc: Alan Stern Cc: Oncaphillis Cc: stable Signed-off-by: Greg Kroah-Hartman

USB: Disable USB 3.0 LPM in critical sections.

2012-05-18T22:41:59Z

There are several places where the USB core needs to disable USB 3.0 Link PM: - usb_bind_interface - usb_unbind_interface - usb_driver_claim_interface - usb_port_suspend/usb_port_resume - usb_reset_and_verify_device - usb_set_interface - usb_reset_configuration - usb_set_configuration Use the new LPM disable/enable functions to temporarily disable LPM around these critical sections. We need to protect the critical section around binding and unbinding USB interface drivers. USB drivers may want to disable hub-initiated USB 3.0 LPM, which will change the value of the U1/U2 timeouts that the xHCI driver will install. We need to disable LPM completely until the driver is bound to the interface, and the driver has a chance to enable whatever alternate interface setting it needs in its probe routine. Then re-enable USB3 LPM, and recalculate the U1/U2 timeout values. We also need to disable LPM in usb_driver_claim_interface, because drivers like usbfs can bind to an interface through that function. Note, there is no way currently for userspace drivers to disable hub-initiated USB 3.0 LPM. Revisit this later. When a driver is unbound, the U1/U2 timeouts may change because we are unbinding the last driver that needed hub-initiated USB 3.0 LPM to be disabled. USB LPM must be disabled when a USB device is going to be suspended. The USB 3.0 spec does not define a state transition from U1 or U2 into U3, so we need to bring the device into U0 by disabling LPM before we can place it into U3. Therefore, call usb_unlocked_disable_lpm() in usb_port_suspend(), and call usb_unlocked_enable_lpm() in usb_port_resume(). If the port suspend fails, make sure to re-enable LPM by calling usb_unlocked_enable_lpm(), since usb_port_resume() will not be called on a failed port suspend. USB 3.0 devices lose their USB 3.0 LPM settings (including whether USB device-initiated LPM is enabled) across device suspend. Therefore, disable LPM before the device will be reset in usb_reset_and_verify_device(), and re-enable LPM after the reset is complete and the configuration/alt settings are re-installed. The calculated U1/U2 timeout values are heavily dependent on what USB device endpoints are currently enabled. When any of the enabled endpoints on the device might change, due to a new configuration, or new alternate interface setting, we need to first disable USB 3.0 LPM, add or delete endpoints from the xHCI schedule, install the new interfaces and alt settings, and then re-enable LPM. Do this in usb_set_interface, usb_reset_configuration, and usb_set_configuration. Basically, there is a call to disable and then enable LPM in all functions that lock the bandwidth_mutex. One exception is usb_disable_device, because the device is disconnecting or otherwise going away, and we should not care about whether USB 3.0 LPM is enabled. Signed-off-by: Sarah Sharp

USB: Add support to enable/disable USB3 link states.

2012-05-18T22:41:58Z

There are various functions within the USB core that will need to disable USB 3.0 link power states. For example, when a USB device driver is being bound to an interface, we need to disable USB 3.0 LPM until we know if the driver will allow hub-initiated LPM transitions. Another example is when the USB core is switching alternate interface settings. The USB 3.0 timeout values are dependent on what endpoints are enabled, so we want to ensure that LPM is disabled until the new alt setting is fully installed. Multiple functions need to disable LPM, and those functions can even be nested. For example, usb_bind_interface() could disable LPM, and then call into the driver probe function, which may attempt to switch to a different alt setting. Therefore, we need to keep a count of the number of functions that require LPM to be disabled at any point in time. Introduce two new USB core API calls, usb_disable_lpm() and usb_enable_lpm(). These functions increment and decrement a new variable in the usb_device, lpm_disable_count. If usb_disable_lpm() fails, it will call usb_enable_lpm() in order to balance the lpm_disable_count. These two new functions must be called with the bandwidth_mutex locked. If the bandwidth_mutex is not already held by the caller, it should instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take the bandwidth_mutex before calling usb_disable_lpm() and usb_enable_lpm(), respectively. Introduce a new variable (timeout) in the usb3_lpm_params structure to keep track of the currently enabled U1/U2 timeout values. When usb_disable_lpm() is called, and the USB device has the U1 or U2 timeouts set to a non-zero value (meaning either device-initiated or hub-initiated LPM is enabled), attempt to disable LPM, regardless of the state of the lpm_disable_count. We want to ensure that all callers can be guaranteed that LPM is disabled if usb_disable_lpm() returns zero. Otherwise the following scenario could occur: 1. Driver A is being bound to interface 1. usb_probe_interface() disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so even though usb_disable_lpm() fails, the probe of the driver continues, and the bandwidth mutex is dropped. 2. Meanwhile, Driver B is being bound to interface 2. usb_probe_interface() grabs the bandwidth mutex and calls usb_disable_lpm(). That call should attempt to disable LPM, even though the lpm_disable_count is set to 1 by Driver A. For usb_enable_lpm(), we attempt to enable LPM only when the lpm_disable_count is zero. If some step in enabling LPM fails, it will only have a minimal impact on power consumption, and all USB device drivers should still work properly. Therefore don't bother to return any error codes. Don't enable device-initiated LPM if the device is unconfigured. The USB device will only accept the U1/U2_ENABLE control transfers in the configured state. Do enable hub-initiated LPM in that case, since devices are allowed to accept the LGO_Ux link commands in any state. Don't enable or disable LPM if the device is marked as not being LPM capable. This can happen if: - the USB device doesn't have a SS BOS descriptor, - the device's parent hub has a zeroed bHeaderDecodeLatency value, or - the xHCI host doesn't support LPM. Signed-off-by: Sarah Sharp Cc: Andiry Xu Cc: Alan Stern Signed-off-by: Sarah Sharp