linux/drivers/usb/serial, branch v5.0

USB: serial: keyspan_usa: add proper SPDX lines for .h files

2019-01-18T10:09:32Z

The keyspan_usa??msg.h files are under a BSD-3 style license, so properly label them as such with a SPDX line at the top of the file. Signed-off-by: Greg Kroah-Hartman Signed-off-by: Johan Hovold

USB: serial: pl2303: add new PID to support PL2303TB

2019-01-17T16:24:39Z

Add new PID to support PL2303TB (TYPE_HX) Signed-off-by: Charles Yeh Cc: stable Signed-off-by: Johan Hovold

USB: serial: ftdi_sio: fix GPIO not working in autosuspend

2019-01-14T13:40:11Z

There is a bug in the current GPIO code for ftdi_sio: it failed to take USB autosuspend into account. If the device is in autosuspend, calls to usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for autosuspend timeout is usually 2-5 seconds, this made it almost impossible to use the GPIOs on machines that have USB autosuspend enabled. This patch fixes the issue by acquiring a PM lock on the device for the duration of the USB transfers. Tested on an FT231X device. Signed-off-by: Karoly Pados [ johan: simplify code somewhat ] Fixes: ba93cc7da896 ("USB: serial: ftdi_sio: implement GPIO support for FT-X devices") Cc: stable # 4.20 Signed-off-by: Johan Hovold

USB: serial: simple: add Motorola Tetra TPG2200 device id

2019-01-07T15:37:52Z

Add new Motorola Tetra device id for Motorola Solutions TETRA PEI device T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0cad ProdID=9016 Rev=24.16 S: Manufacturer=Motorola Solutions, Inc. S: Product=TETRA PEI interface C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_serial_simple I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb_serial_simple Signed-off-by: Max Schulze Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add Fibocom NL678 series

2018-12-21T15:47:02Z

Added USB serial option driver support for Fibocom NL678 series cellular module: VID 2cb7 and PIDs 0x0104 and 0x0105. Reserved network and ADB interfaces. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2cb7 ProdID=0104 Rev=03.10 S: Manufacturer=Fibocom S: Product=Fibocom NL678-E Modem S: SerialNumber=12345678 C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2cb7 ProdID=0105 Rev=03.10 S: Manufacturer=Fibocom S: Product=Fibocom NL678-E Modem S: SerialNumber=12345678 C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by: Jörgen Storvist Cc: stable Acked-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

Merge USB 4.20-rc8 mergepoint into usb-next

2018-12-21T15:46:08Z

We need the USB changes in here for additional patches to be able to apply cleanly. Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

2018-12-21T07:36:54Z

Johan writes: USB-serial updates for 4.21-rc1 Here are the USB-serial updates for 4.21-rc1, including: - support for mos7840 3-port devices - improved ftdi baud-rate divisor calculations - support for a new class of f81534 devices Included are also various clean ups and some new pl2303 device ids. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold * tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays USB: serial: mos7840: remove set but not used variables 'number, serial' USB: serial: mos7840: add a product ID for the new product USB: serial: mos7840: clean up register handling USB: serial: ftdi_sio: use rounding when calculating baud rate divisors USB: serial: f81534: fix reading old/new IC config USB: serial: mos7840: remove set but not used variables 'st, data1, iflag' USB: serial: quatech2: remove set but not used variable 'port_priv'

USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays

2018-12-18T09:22:37Z

Add device ids to pl2303 for the HP POS pole displays: LM920: 03f0:026b TD620: 03f0:0956 LD960TA: 03f0:4439 LD220TA: 03f0:4349 LM940: 03f0:5039 Signed-off-by: Scott Chen Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add Telit LN940 series

2018-12-13T19:08:00Z

Added USB serial option driver support for Telit LN940 series cellular modules. Covering both QMI and MBIM modes. usb-devices output (0x1900): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1900 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option usb-devices output (0x1901): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 20 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1901 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add Fibocom NL668 series

2018-12-13T10:24:58Z

Added USB serial option driver support for Fibocom NL668 series cellular modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces. usb-devices output (QMI mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) usb-devices output (ECM mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold