linux/drivers/usb/serial, branch v5.2

USB: serial: option: add Telit 0x1260 and 0x1261 compositions

2019-05-21T09:27:24Z

Added support for Telit LE910Cx 0x1260 and 0x1261 compositions. Signed-off-by: Daniele Palmas Cc: stable Signed-off-by: Johan Hovold

USB: serial: pl2303: add Allied Telesis VT-Kit3

2019-05-21T09:26:14Z

This is adds the vendor and device id for the AT-VT-Kit3 which is a pl2303-based device. Signed-off-by: Chris Packham Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode

2019-05-21T09:19:02Z

Added IDs for Simcom SIM7500/SIM7600 series cellular module in RNDIS mode. Reserved the interface for ADB. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9011 Rev=03.18 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C: #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: f81232: implement break control

2019-05-03T07:19:55Z

Implement Fintek F81232 break on/off with LCR register. It's the same with 16550A LCR register layout. Signed-off-by: Ji-Ze Hong (Peter Hong) [ johan: fix corrupt line settings on break due to missing shadow_lcr update in set_termios() ] Signed-off-by: Johan Hovold

USB: serial: f81232: add high baud rate support

2019-05-03T07:19:54Z

The F81232 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates can be up to 1.5Mbits with 24MHz. F81232 Clock registers (106h) Bit1-0: Clock source selector 00: 1.846MHz. 01: 18.46MHz. 10: 24MHz. 11: 14.77MHz. Signed-off-by: Ji-Ze Hong (Peter Hong) Signed-off-by: Johan Hovold

USB: serial: f81232: clear overrun flag

2019-05-03T07:19:54Z

The F81232 will report data and LSR with bulk like following format: bulk-in data: [LSR(1Byte)+DATA(1Byte)][LSR(1Byte)+DATA(1Byte)]... LSR will auto clear frame/parity/break error flag when reading by H/W, but overrrun will only cleared when reading LSR. So this patch add a worker to read LSR when overrun and flush the worker on close() & suspend(). Cc: Oliver Neukum Signed-off-by: Ji-Ze Hong (Peter Hong) Signed-off-by: Johan Hovold

USB: serial: f81232: fix interrupt worker not stop

2019-05-03T07:18:31Z

The F81232 will use interrupt worker to handle MSR change. This patch will fix the issue that interrupt work should stop in close() and suspend(). This also fixes line-status events being disabled after a suspend cycle until the port is re-opened. Signed-off-by: Ji-Ze Hong (Peter Hong) [ johan: amend commit message ] Fixes: 87fe5adcd8de ("USB: f81232: implement read IIR/MSR with endpoint") Cc: stable # 4.1 Signed-off-by: Johan Hovold

USB: serial: io_edgeport: fix up switch fall-through comments

2019-05-03T06:01:11Z

Gustavo has been working to fix up all of the switch statements that "fall through" such that we can eventually turn on -Wimplicit-fallthrough. As part of that, the io_edgeport.c driver is a bit "messy" with the parsing logic of a data packet. Clean that logic up a bit by unindenting one level of the logic, and properly label /* Fall through */ to make gcc happy. Reported-by: Gustavo A. R. Silva Signed-off-by: Greg Kroah-Hartman Acked-by: Gustavo A. R. Silva Signed-off-by: Johan Hovold

USB: serial: drop unnecessary goto

2019-04-30T08:25:04Z

Drop an unnecessary goto from a write-urb completion error path. Signed-off-by: Johan Hovold

USB: serial: clean up throttle handling

2019-04-30T08:23:29Z

Clean up the throttle implementation by dropping the redundant throttle_req flag which was a remnant from back when there was only a single read URB. Also convert the throttled flag to an atomic bit flag. Signed-off-by: Johan Hovold