linux/drivers/usb/serial, branch v5.3

USB: serial: option: add the BroadMobi BM818 card

2019-08-15T11:46:22Z

Add a VID:PID for the BroadMobi BM818 M.2 card T: Bus=01 Lev=03 Prnt=40 Port=03 Cnt=01 Dev#= 44 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2060 Rev=00.00 S: Manufacturer=Qualcomm, Incorporated S: Product=Qualcomm CDMA Technologies MSM C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=(none) I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) Signed-off-by: Bob Ham Signed-off-by: Angus Ainslie (Purism) Cc: stable [ johan: use USB_DEVICE_INTERFACE_CLASS() ] Signed-off-by: Johan Hovold

USB: serial: option: Add Motorola modem UARTs

2019-08-15T11:28:47Z

On Motorola Mapphone devices such as Droid 4 there are five USB ports that do not use the same layout as Gobi 1K/2K/etc devices listed in qcserial.c. So we should use qcaux.c or option.c as noted by Dan Williams . As the Motorola USB serial ports have an interrupt endpoint as shown with lsusb -v, we should use option.c instead of qcaux.c as pointed out by Johan Hovold . The ff/ff/ff interfaces seem to always be UARTs on Motorola devices. For the other interfaces, class 0x0a (CDC Data) should not in general be added as they are typically part of a multi-interface function as noted earlier by Bjørn Mork . However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a class is only used for flashing the modem firmware, and there are no other interfaces. So I've added that too with more details below as it works just fine. The ttyUSB ports on Droid 4 are: ttyUSB0 DIAG, CQDM-capable ttyUSB1 MUX or NMEA, no response ttyUSB2 MUX or NMEA, no response ttyUSB3 TCMD ttyUSB4 AT-capable The ttyUSB0 is detected as QCDM capable by ModemManager. I think it's only used for debugging with ModemManager --debug for sending custom AT commands though. ModemManager already can manage data connection using the USB QMI ports that are already handled by the qmi_wwan.c driver. To enable the MUX or NMEA ports, it seems that something needs to be done additionally to enable them, maybe via the DIAG or TCMD port. It might be just a NVRAM setting somewhere, but I have no idea what NVRAM settings may need changing for that. The TCMD port seems to be a Motorola custom protocol for testing the modem and to configure it's NVRAM and seems to work just fine based on a quick test with a minimal tcmdrw tool I wrote. The voice modem AT-capable port seems to provide only partial support, and no PM support compared to the TS 27.010 based UART wired directly to the modem. The UARTs added with this change are the same product IDs as the Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't have any mdm9600 based devices, so I have only tested these on mdm6600 based droid 4. Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android Linux kernel driver moto_flashqsc.c just seems to change the port->bulk_out_size to 8K from the default. And is only used for flashing the modem firmware it seems. I've verified that flashing the modem with signed firmware works just fine with the option driver after manually toggling the GPIO pins, so I've added droid 4 modem flashing mode to the option driver. I've not added the other devices listed in moto_flashqsc.c in case they really need different port->bulk_out_size. Those can be added as they get tested to work for flashing the modem. After this patch the output of /sys/kernel/debug/usb/devices has the following for normal 22b8:2a70 mode including the related qmi_wwan interfaces: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=2a70 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms In 22b8:900e "qc_dload" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=900e Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms And in 22b8:4281 "ram_downloader" mode the device shows up as: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=22b8 ProdID=4281 Rev= 0.00 S: Manufacturer=Motorola, Incorporated S: Product=Flash MZ600 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms Cc: Bjørn Mork Cc: Dan Williams Cc: Lars Melin Cc: Marcel Partap Cc: Merlijn Wajer Cc: Michael Scott Cc: NeKit Cc: Pavel Machek Cc: Sebastian Reichel Tested-by: Pavel Machek Signed-off-by: Tony Lindgren Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add D-Link DWM-222 device ID

2019-08-05T11:34:17Z

Add device id for D-Link DWM-222 A2. MI_00 D-Link HS-USB Diagnostics MI_01 D-Link HS-USB Modem MI_02 D-Link HS-USB AT Port MI_03 D-Link HS-USB NMEA MI_04 D-Link HS-USB WWAN Adapter (qmi_wwan) MI_05 USB Mass Storage Device Cc: stable@vger.kernel.org Signed-off-by: Rogan Dawes Signed-off-by: Johan Hovold

USB: serial: option: Add support for ZTE MF871A

2019-08-05T11:26:33Z

This patch adds support for MF871A USB modem (aka Speed USB STICK U03) to option driver. This modem is manufactured by ZTE corporation, and sold by KDDI. Interface layout: 0: AT 1: MODEM usb-devices output: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1481 Rev=52.87 S: Manufacturer=ZTE,Incorporated S: Product=ZTE Technologies MSM S: SerialNumber=1234567890ABCDEF C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Co-developed-by: Hiroyuki Yamamoto Signed-off-by: Hiroyuki Yamamoto Signed-off-by: Yoshiaki Okamoto Cc: stable Signed-off-by: Johan Hovold

Merge tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

2019-07-03T07:20:31Z

Johan writes: USB-serial updates for 5.3-rc1 Here are the USB-serial updates for 5.3-rc1; just some new device ids this time. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold * tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: ftdi_sio: add ID for isodebug v1 USB: serial: option: add support for GosunCn ME3630 RNDIS mode

USB: serial: ftdi_sio: add ID for isodebug v1

2019-06-28T15:12:35Z

This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the second channel is available for use as a serial port. Signed-off-by: Andreas Fritiofson Cc: stable Signed-off-by: Johan Hovold

docs: usb: rename files to .rst and add them to drivers-api

2019-06-20T12:28:36Z

While there are a mix of things here, most of the stuff were written from Kernel developer's PoV. So, add them to the driver-api book. A follow up for this patch would be to move documents from there that are specific to sysadmins, adding them to the admin-guide. Signed-off-by: Mauro Carvalho Chehab Acked-by: Johan Hovold Acked-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add support for GosunCn ME3630 RNDIS mode

2019-06-19T12:08:36Z

Added USB IDs for GosunCn ME3630 cellular module in RNDIS mode. T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=03 Dev#= 18 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0601 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber=b950269c C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add Telit 0x1260 and 0x1261 compositions

2019-05-21T09:27:24Z

Added support for Telit LE910Cx 0x1260 and 0x1261 compositions. Signed-off-by: Daniele Palmas Cc: stable Signed-off-by: Johan Hovold

USB: serial: pl2303: add Allied Telesis VT-Kit3

2019-05-21T09:26:14Z

This is adds the vendor and device id for the AT-VT-Kit3 which is a pl2303-based device. Signed-off-by: Chris Packham Cc: stable Signed-off-by: Johan Hovold