linux/drivers/usb, branch v3.5

Merge tag 'mfd-for-linus-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

2012-07-13T16:54:26Z

Pull MFD Fixes from Samuel Ortiz: - Three Palmas fixes, One of them being a build error fix. - Two mc13xx fixes. One for fixing an SPI regmap configuration and another one for working around an i.Mx hardware bug. - One omap-usb regression fix. - One twl6040 build breakage fix. - One file deletion (ab5500-core.h) that was overlooked during the last merge window. * tag 'mfd-for-linus-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: mfd: Add missing hunk to change palmas irq to clear on read mfd: Fix palmas regulator pdata missing mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix issues. mfd: Update twl6040 Kconfig to avoid build breakage mfd: Delete ab5500-core.h mfd: mc13xxx workaround SPI hardware bug on i.Mx mfd: Fix mc13xxx SPI regmap mfd: Add terminating entry for i2c_device_id palmas table

mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix issues.

2012-07-08T22:16:25Z

'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes an issue where the ULPI PHYs were not held in reset while initializing the EHCI controller. However, it also changes behavior in omap-usb-host.c omap_usbhs_init by releasing reset while the configuration in that function was done. This change caused a regression on BB-xM where USB would not function if 'usb start' had been run from u-boot before booting. A change was made to release reset a little bit earlier which fixed the issue on BB-xM and did not cause any regressions on 3430 sdp, the board for which the fix was originally made. This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle before adding hcd.', (3aa2ae74) caused a regression on OMAP5. The original fix to hold the EHCI controller in reset during initialization was correct, however it appears that changing omap_usbhs_init to not hold the PHYs in reset during it's configuration was incorrect. This patch first reverts both fixes, and then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in reset as the original patch had done. It also is sure to incorporate the _cansleep change that has been made in the meantime. I've tested this on Beagleboard xM, I'd really like to get an ack from the 3430 sdp and OMAP5 guys before getting this merged. v3 - Brown paper bag its too early in the morning actually run git commit amend fix v2 - Put cansleep gpiolib call outside of spinlock Acked-by: Mantesh Sarashetti Tested-by: Mantesh Sarashetti Acked-by: Keshava Munegowda Tested-by: Keshava Munegowda Signed-off-by: Russ Dill Signed-off-by: Samuel Ortiz

USB: cdc-wdm: fix lockup on error in wdm_read

2012-07-05T23:04:58Z

Clear the WDM_READ flag on empty reads to avoid running forever in an infinite tight loop, causing lockups: Jul 1 21:58:11 nemi kernel: [ 3658.898647] qmi_wwan 2-1:1.2: Unexpected error -71 Jul 1 21:58:36 nemi kernel: [ 3684.072021] BUG: soft lockup - CPU#0 stuck for 23s! [qmi.pl:12235] Jul 1 21:58:36 nemi kernel: [ 3684.072212] CPU 0 Jul 1 21:58:36 nemi kernel: [ 3684.072355] Jul 1 21:58:36 nemi kernel: [ 3684.072367] Pid: 12235, comm: qmi.pl Tainted: P O 3.5.0-rc2+ #13 LENOVO 2776LEG/2776LEG Jul 1 21:58:36 nemi kernel: [ 3684.072383] RIP: 0010:[] [] spin_unlock_irq+0x8/0xc [cdc_wdm] Jul 1 21:58:36 nemi kernel: [ 3684.072388] RSP: 0018:ffff88022dca1e70 EFLAGS: 00000282 Jul 1 21:58:36 nemi kernel: [ 3684.072393] RAX: ffff88022fc3f650 RBX: ffffffff811c56f7 RCX: 00000001000ce8c1 Jul 1 21:58:36 nemi kernel: [ 3684.072398] RDX: 0000000000000010 RSI: 000000000267d810 RDI: ffff88022fc3f650 Jul 1 21:58:36 nemi kernel: [ 3684.072403] RBP: ffff88022dca1eb0 R08: ffffffffa063578e R09: 0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072407] R10: 0000000000000008 R11: 0000000000000246 R12: 0000000000000002 Jul 1 21:58:36 nemi kernel: [ 3684.072412] R13: 0000000000000246 R14: ffffffff00000002 R15: ffff8802281d8c88 Jul 1 21:58:36 nemi kernel: [ 3684.072418] FS: 00007f666a260700(0000) GS:ffff88023bc00000(0000) knlGS:0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072423] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Jul 1 21:58:36 nemi kernel: [ 3684.072428] CR2: 000000000270d9d8 CR3: 000000022e865000 CR4: 00000000000007f0 Jul 1 21:58:36 nemi kernel: [ 3684.072433] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072438] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Jul 1 21:58:36 nemi kernel: [ 3684.072444] Process qmi.pl (pid: 12235, threadinfo ffff88022dca0000, task ffff88022ff76380) Jul 1 21:58:36 nemi kernel: [ 3684.072448] Stack: Jul 1 21:58:36 nemi kernel: [ 3684.072458] ffffffffa063592e 0000000100020000 ffff88022fc3f650 ffff88022fc3f6a8 Jul 1 21:58:36 nemi kernel: [ 3684.072466] 0000000000000200 0000000100000000 000000000267d810 0000000000000000 Jul 1 21:58:36 nemi kernel: [ 3684.072475] 0000000000000000 ffff880212cfb6d0 0000000000000200 ffff880212cfb6c0 Jul 1 21:58:36 nemi kernel: [ 3684.072479] Call Trace: Jul 1 21:58:36 nemi kernel: [ 3684.072489] [] ? wdm_read+0x1a0/0x263 [cdc_wdm] Jul 1 21:58:36 nemi kernel: [ 3684.072500] [] ? vfs_read+0xa1/0xfb Jul 1 21:58:36 nemi kernel: [ 3684.072509] [] ? alarm_setitimer+0x35/0x64 Jul 1 21:58:36 nemi kernel: [ 3684.072517] [] ? sys_read+0x45/0x6e Jul 1 21:58:36 nemi kernel: [ 3684.072525] [] ? system_call_fastpath+0x16/0x1b Jul 1 21:58:36 nemi kernel: [ 3684.072557] Code: <66> 66 90 c3 83 ff ed 89 f8 74 16 7f 06 83 ff a1 75 0a c3 83 ff f4 The WDM_READ flag is normally cleared by wdm_int_callback before resubmitting the read urb, and set by wdm_in_callback when this urb returns with data or an error. But a crashing device may cause both a read error and cancelling all urbs. Make sure that the flag is cleared by wdm_read if the buffer is empty. We don't clear the flag on errors, as there may be pending data in the buffer which should be processed. The flag will instead be cleared on the next wdm_read call. Cc: stable Signed-off-by: Bjørn Mork Acked-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman

USB: metro-usb: fix tty_flip_buffer_push use

2012-07-05T23:04:57Z

Do not set low_latency flag at open as tty_flip_buffer_push must not be called in IRQ context with low_latency set. Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: option: Add MEDIATEK product ids

2012-07-05T23:00:22Z

Signed-off-by: Gaosen Zhang Cc: stable Signed-off-by: Greg Kroah-Hartman

USB: option: add ZTE MF60

2012-07-05T22:57:18Z

Switches into a composite device by ejecting the initial driver CD. The four interfaces are: QCDM, AT, QMI/wwan and mass storage. Let this driver manage the two serial interfaces: T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 28 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1402 Rev= 0.00 S: Manufacturer=ZTE,Incorporated S: Product=ZTE WCDMA Technologies MSM S: SerialNumber=xxxxx C:* #Ifs= 4 Cfg#= 1 Atr=c0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Bjørn Mork Cc: stable Signed-off-by: Greg Kroah-Hartman

xhci: Fix hang on back-to-back Set TR Deq Ptr commands.

2012-07-02T19:51:25Z

The Microsoft LifeChat 3000 USB headset was causing a very reproducible hang whenever it was plugged in. At first, I thought the host controller was producing bad transfer events, because the log was filled with errors like: xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD However, it turned out to be an xHCI driver bug in the ring expansion patches. The bug is triggered When there are two ring segments, and a TD that ends just before a link TRB, like so: ______________ _____________ | | ---> | setup TRB B | ______________ | _____________ | | | | data TRB B | ______________ | _____________ | setup TRB A | <-- deq | | data TRB B | ______________ | _____________ | data TRB A | | | | <-- enq, deq'' ______________ | _____________ | status TRB A | | | | ______________ | _____________ | link TRB |--------------- | link TRB | _____________ <--- deq' _____________ TD A (the first control transfer) stalls on the data phase. That halts the ring. The xHCI driver moves the hardware dequeue pointer to the first TRB after the stalled transfer, which happens to be the link TRB. Once the Set TR dequeue pointer command completes, the function update_ring_for_set_deq_completion runs. That function is supposed to update the xHCI driver's dequeue pointer to match the internal hardware dequeue pointer. On the first call this would work fine, and the software dequeue pointer would move to deq'. However, if the transfer immediately after that stalled (TD B in this case), another Set TR Dequeue command would be issued. That would move the hardware dequeue pointer to deq''. Once that command completed, update_ring_for_set_deq_completion would run again. The original code would unconditionally increment the software dequeue pointer, which moved the pointer off the ring segment into la-la-land. The while loop would happy increment the dequeue pointer (possibly wrapping it) until it matched the hardware pointer value. The while loop would also access all the memory in between the first ring segment and the second ring segment to determine if it was a link TRB. This could cause general protection faults, although it was unlikely because the ring segments came from a DMA pool, and would often have consecutive memory addresses. If nothing in that space looked like a link TRB, the deq_seg pointer for the ring would remain on the first segment. Thus, the deq_seg and the software dequeue pointer would get out of sync. When the next transfer event came in after the stalled transfer, the xHCI driver code would attempt to convert the software dequeue pointer into a DMA address in order to compare the DMA address for the completed transfer. Since the deq_seg and the dequeue pointer were out of sync, xhci_trb_virt_to_dma would return NULL. The transfer event would get ignored, the transfer would eventually timeout, and we would mistakenly convert the finished transfer to no-op TRBs. Some kernel driver (maybe xHCI?) would then get stuck in an infinite loop in interrupt context, and the whole machine would hang. This patch should be backported to kernels as old as 3.4, that contain the commit b008df60c6369ba0290fa7daa177375407a12e07 "xHCI: count free TRBs on transfer ring" Signed-off-by: Sarah Sharp Cc: Andiry Xu Cc: stable@vger.kernel.org

usb: Add support for root hub port status CAS

2012-07-02T19:51:24Z

The host controller port status register supports CAS (Cold Attach Status) bit. This bit could be set when USB3.0 device is connected when system is in Sx state. When the system wakes to S0 this port status with CAS bit is reported and this port can't be used by any device. When CAS bit is set the port should be reset by warm reset. This was not supported by xhci driver. The issue was found when pendrive was connected to suspended platform. The link state of "Compliance Mode" was reported together with CAS bit. This link state was also not supported by xhci and core/hub.c. The CAS bit is defined only for xhci root hub port and it is not supported on regular hubs. The link status is used to force warm reset on port. Make the USB core issue a warm reset when port is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver to report 'compliance mode' when the CAS is set. This force warm reset on the root hub port. This patch should be backported to stable kernels as old as 3.2, that contain the commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When hot reset for USB3 fails, try warm reset." Signed-off-by: Stanislaw Ledwon Signed-off-by: Sarah Sharp Acked-by: Andiry Xu Cc: stable@vger.kernel.org

USB: CP210x Add 10 Device IDs

2012-06-26T23:14:34Z

This patch adds 10 device IDs for CP210x based devices from the following manufacturers: Timewave Clipsal Festo Link Instruments Signed-off-by: Craig Shelley Cc: stable Signed-off-by: Greg Kroah-Hartman

USB: option: Add USB ID for Novatel Ovation MC551

2012-06-26T23:14:34Z

This device is also known as the Verizon USB551L. Signed-off-by: Forest Bond Acked-by: Dan Williams Cc: stable Signed-off-by: Greg Kroah-Hartman