linux/drivers/usb, branch v4.0

Merge tag 'usb-serial-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

2015-04-01T11:42:58Z

Johan writes: USB-serial fixes for v4.0-rc6 Here are a few new device IDs. Signed-off-by: Johan Hovold

USB: ftdi_sio: Use jtag quirk for SNAP Connect E10

2015-03-25T14:32:53Z

This patch uses the existing CALAO Systems ftdi_8u2232c_probe in order to avoid attaching a TTY to the JTAG port as this board is based on the CALAO Systems reference design and needs the same fix up. Signed-off-by: Doug Goldstein CC: stable [johan: clean up probe logic ] Signed-off-by: Johan Hovold

Merge tag 'fixes-for-v4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

2015-03-24T22:01:58Z

Felipe writes: usb: fix for v4.0-rc6 Here's a single fix to isp1760 calling spin_unlock_irqsave() as we should have. Signed-off-by: Felipe Balbi

usb: isp1760: fix spin unlock in the error path of isp1760_udc_start

2015-03-24T16:38:58Z

Commit a124820de5fd ("usb: isp1760: fix possible deadlock in isp1760_udc_irq") replaced spin_{un,}lock with spin_{un,}lock_irq{save,restore}. However it missed an error path resulting in the smatch warning as below: drivers/usb/isp1760/isp1760-udc.c:1230 isp1760_udc_start() warn: inconsistent returns 'irqsave:flags'. Locked on: line 1207 Unlocked on: line 1199 This patch fixes the spin unlock in the error path in isp1760_udc_start thereby removing the smatch warning mentioned above. Reported-by: Dan Carpenter Cc: Laurent Pinchart Cc: Felipe Balbi Signed-off-by: Sudeep Holla Signed-off-by: Felipe Balbi

usb: xhci: apply XHCI_AVOID_BEI quirk to all Intel xHCI controllers

2015-03-23T20:51:12Z

When a device with an isochronous endpoint is plugged into the Intel xHCI host controller, and the driver submits multiple frames per URB, the xHCI driver will set the Block Event Interrupt (BEI) flag on all but the last TD for the URB. This causes the host controller to place an event on the event ring, but not send an interrupt. When the last TD for the URB completes, BEI is cleared, and we get an interrupt for the whole URB. However, under Intel xHCI host controllers, if the event ring is full of events from transfers with BEI set, an "Event Ring is Full" event will be posted to the last entry of the event ring, but no interrupt is generated. Host will cease all transfer and command executions and wait until software completes handling the pending events in the event ring. That means xHC stops, but event of "event ring is full" is not notified. As the result, the xHC looks like dead to user. This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And it should be backported to kernels as old as 3.0, that contains the commit 69e848c2090a ("Intel xhci: Support EHCI/xHCI port switching."). Signed-off-by: Lu Baolu Tested-by: Alistair Grant Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

usb: xhci: handle Config Error Change (CEC) in xhci driver

2015-03-23T20:51:12Z

Linux xHCI driver doesn't report and handle port cofig error change. If Port Configure Error for root hub port occurs, CEC bit in PORTSC would be set by xHC and remains 1. This happends when the root port fails to configure its link partner, e.g. the port fails to exchange port capabilities information using Port Capability LMPs. Then the Port Status Change Events will be blocked until all status change bits(CEC is one of the change bits) are cleared('0') (refer to xHCI spec 4.19.2). Otherwise, the port status change event for this root port will not be generated anymore, then root port would look like dead for user and can't be recovered until a Host Controller Reset(HCRST). This patch is to check CEC bit in PORTSC in xhci_get_port_status() and set a Config Error in the return status if CEC is set. This will cause a ClearPortFeature request, where CEC bit is cleared in xhci_clear_port_change_bit(). [The commit log is based on initial Marvell patch posted at http://marc.info/?l=linux-kernel&m=142323612321434&w=2] Reported-by: Gregory CLEMENT Signed-off-by: Lu Baolu Cc: stable # v3.2+ Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2015-03-22T18:33:55Z

Pull USB / PHY driver fixes from Greg KH: "Here's a number of USB and PHY driver fixes for 4.0-rc5. The largest thing here is a revert of a gadget function driver patch that removes 500 lines of code. Other than that, it's a number of reported bugs fixes and new quirk/id entries. All have been in linux-next for a while" * tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits) usb: common: otg-fsm: only signal connect after switching to peripheral uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices USB: ehci-atmel: rework clk handling MAINTAINERS: add entry for USB OTG FSM usb: chipidea: otg: add a_alt_hnp_support response for B device phy: omap-usb2: Fix missing clk_prepare call when using old dt name phy: ti/omap: Fix modalias phy: core: Fixup return value of phy_exit when !pm_runtime_enabled phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof phy: twl4030-usb: Remove redundant assignment for twl->linkstat phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0] phy: Find the right match in devm_phy_destroy() phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation phy: samsung-usb2: Remove NULL terminating entry from phys array phy: hix5hd2-sata: Check return value of platform_get_resource phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function Revert "usb: gadget: zero: Add support for interrupt EP" Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'" ...

Merge git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending

2015-03-21T18:24:38Z

Pull SCSI target fixes from Nicholas Bellinger: "Here are current target-pending fixes for v4.0-rc5 code that have made their way into the queue over the last weeks. The fixes this round include: - Fix long-standing iser-target logout bug related to early conn_logout_comp completion, resulting in iscsi_conn use-after-tree OOpsen. (Sagi + nab) - Fix long-standing tcm_fc bug in ft_invl_hw_context() failure handing for DDP hw offload. (DanC) - Fix incorrect use of unprotected __transport_register_session() in tcm_qla2xxx + other single local se_node_acl fabrics. (Bart) - Fix reference leak in target_submit_cmd() -> target_get_sess_cmd() for ack_kref=1 failure path. (Bart) - Fix pSCSI backend ->get_device_type() statistics OOPs with un-configured device. (Olaf + nab) - Fix virtual LUN=0 target_configure_device failure OOPs at modprobe time. (Claudio + nab) - Fix FUA write false positive failure regression in v4.0-rc1 code. (Christophe Vu-Brugier + HCH)" * git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0 target: Fix virtual LUN=0 target_configure_device failure OOPs target/pscsi: Fix NULL pointer dereference in get_device_type tcm_fc: missing curly braces in ft_invl_hw_context() target: Fix reference leak in target_get_sess_cmd() error path loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session tcm_qla2xxx: Fix incorrect use of __transport_register_session iscsi-target: Avoid early conn_logout_comp for iser connections Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target" target: Disallow changing of WRITE cache/FUA attrs after export

loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session

2015-03-20T06:15:14Z

This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback fabric code to invoke transport_register_session() instead of the unprotected flavour, to ensure se_tpg->session_lock is taken when adding new session list nodes to se_tpg->tpg_sess_list. Note that since these four fabric drivers already hold their own internal TPG mutexes when accessing se_tpg->tpg_sess_list, and consist of a single se_session created through configfs attribute access, no list corruption can currently occur. So for correctness sake, go ahead and use the se_tpg->session_lock protected version for these four fabric drivers. Signed-off-by: Bart Van Assche Signed-off-by: Nicholas Bellinger

USB: keyspan_pda: add new device id

2015-03-19T17:04:01Z

Add USB VID/PID for Xircom PGMFHUB USB/serial component. (The hub and SCSI bridge on that hardware are recognized out of the box by existing drivers.) Tested VID/PID using new_id and loopback connection and was met with success, but that's all the testing done. Signed-off-by: Nathaniel Wesley Filardo Cc: stable Signed-off-by: Johan Hovold