linux/drivers/usb, branch v4.20

USB: xhci: fix 'broken_suspend' placement in struct xchi_hcd

2018-12-17T15:01:02Z

As commented in the struct's definition there shouldn't be anything underneath its 'priv[0]' member as it would break some macros. The patch converts the broken_suspend into a bit-field and relocates it next to to the rest of bit-fields. Fixes: a7d57abcc8a5 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC") Reported-by: Oliver Neukum Signed-off-by: Nicolas Saenz Julienne Acked-by: Mathias Nyman Cc: stable Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-serial-4.20-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

2018-12-14T16:06:09Z

Johan writes: USB-serial fixes for 4.20-rc7 Here are some new modem device ids. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold * tag 'usb-serial-4.20-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: add Telit LN940 series USB: serial: option: add Fibocom NL668 series USB: serial: option: add Simcom SIM7500/SIM7600 (MBIM mode) USB: serial: option: add GosunCn ZTE WeLink ME3630 USB: serial: option: add HP lt4132

xhci: Don't prevent USB2 bus suspend in state check intended for USB3 only

2018-12-14T12:02:55Z

The code to prevent a bus suspend if a USB3 port was still in link training also reacted to USB2 port polling state. This caused bus suspend to busyloop in some cases. USB2 polling state is different from USB3, and should not prevent bus suspend. Limit the USB3 link training state check to USB3 root hub ports only. The origial commit went to stable so this need to be applied there as well Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman

USB: serial: option: add Telit LN940 series

2018-12-13T19:08:00Z

Added USB serial option driver support for Telit LN940 series cellular modules. Covering both QMI and MBIM modes. usb-devices output (0x1900): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1900 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option usb-devices output (0x1901): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 20 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1901 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add Fibocom NL668 series

2018-12-13T10:24:58Z

Added USB serial option driver support for Fibocom NL668 series cellular modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces. usb-devices output (QMI mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) usb-devices output (ECM mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add Simcom SIM7500/SIM7600 (MBIM mode)

2018-12-12T16:13:39Z

Added USB serial option driver support for Simcom SIM7500/SIM7600 series cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9003 Rev=03.18 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add GosunCn ZTE WeLink ME3630

2018-12-12T16:13:38Z

Added USB serial option driver support for GosunCn ZTE WeLink ME3630 series cellular modules for USB modes ECM/NCM and MBIM. usb-devices output MBIM mode: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=0602 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim usb-devices output ECM/NCM mode: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=1476 Rev=03.18 S: Manufacturer=Android S: Product=Android S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether Signed-off-by: Jörgen Storvist Cc: stable Signed-off-by: Johan Hovold

USB: serial: option: add HP lt4132

2018-12-10T08:59:00Z

The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem. The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf files included with the Windows driver. Attaching the option driver to it doesn't result in a /dev/ttyUSB* device being created, so I've excluded it. Note that it is also excluded for corresponding Huawei-branded devices, cf. commit d544db293a44 ("USB: support new huawei devices in option.c"). T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none) I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option Signed-off-by: Tore Anderson Cc: stable@vger.kernel.org [ johan: drop id defines ] Signed-off-by: Johan Hovold

Merge tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

2018-12-06T17:02:58Z

Johan writes: USB-serial fix for v4.20-rc6 Here's a fix for a reported USB-console regression in 4.18 which revealed a long-standing bug in the console implementation. The patch has been in linux-next over night with no reported issues. Signed-off-by: Johan Hovold * tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: console: fix reported terminal settings

xhci: Prevent U1/U2 link pm states if exit latency is too long

2018-12-06T12:00:10Z

Don't allow USB3 U1 or U2 if the latency to wake up from the U-state reaches the service interval for a periodic endpoint. This is according to xhci 1.1 specification section 4.23.5.2 extra note: "Software shall ensure that a device is prevented from entering a U-state where its worst case exit latency approaches the ESIT." Allowing too long exit latencies for periodic endpoint confuses xHC internal scheduling, and new devices may fail to enumerate with a "Not enough bandwidth for new device state" error from the host. Cc: Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman