linux/drivers/usb, branch v5.4

usb: dwc3: gadget: fix race when disabling ep with cancelled xfers

2019-10-31T17:57:54Z

When disabling an endpoint which has cancelled requests, we should make sure to giveback requests that are currently pending in the cancelled list, otherwise we may fall into a situation where command completion interrupt fires after endpoint has been disabled, therefore causing a splat. Fixes: fec9095bdef4 "usb: dwc3: gadget: remove wait_end_transfer" Reported-by: Roger Quadros Signed-off-by: Felipe Balbi Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com Signed-off-by: Greg Kroah-Hartman

usb: cdns3: gadget: Fix g_audio use case when connected to Super-Speed host

2019-10-30T13:39:07Z

Take into account gadget driver's speed limit when programming controller speed. Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver") Signed-off-by: Roger Quadros Acked-by: Peter Chen Link: https://lore.kernel.org/r/20191030121607.21739-1-rogerq@ti.com Signed-off-by: Greg Kroah-Hartman

usb: cdns3: gadget: reset EP_CLAIMED flag while unloading

2019-10-30T11:52:13Z

EP_CLAIMED flag is used to track the claimed endpoints. While unloading the module, Reset EP_CLAIMED flag for all enabled endpoints. So that it can be reused. Signed-off-by: Sanket Parmar Acked-by: Peter Chen Reviewed-by: Roger Quadros Acked-by: Felipe Balbi Link: https://lore.kernel.org/r/20191029122441.5816-1-sparmar@cadence.com Signed-off-by: Greg Kroah-Hartman

USB: serial: whiteheat: fix line-speed endianness

2019-10-30T09:06:32Z

Add missing endianness conversion when setting the line speed so that this driver might work also on big-endian machines. Also use an unsigned format specifier in the corresponding debug message. Signed-off-by: Johan Hovold Cc: stable Link: https://lore.kernel.org/r/20191029102354.2733-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman

USB: serial: whiteheat: fix potential slab corruption

2019-10-30T09:06:31Z

Fix a user-controlled slab buffer overflow due to a missing sanity check on the bulk-out transfer buffer used for control requests. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable Signed-off-by: Johan Hovold Link: https://lore.kernel.org/r/20191029102354.2733-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman

USB: gadget: Reject endpoints with 0 maxpacket value

2019-10-29T08:56:18Z

Endpoints with a maxpacket length of 0 are probably useless. They can't transfer any data, and it's not at all unlikely that a UDC will crash or hang when trying to handle a non-zero-length usb_request for such an endpoint. Indeed, dummy-hcd gets a divide error when trying to calculate the remainder of a transfer length by the maxpacket value, as discovered by the syzbot fuzzer. Currently the gadget core does not check for endpoints having a maxpacket value of 0. This patch adds a check to usb_ep_enable(), preventing such endpoints from being used. As far as I know, none of the gadget drivers in the kernel tries to create an endpoint with maxpacket = 0, but until now there has been nothing to prevent userspace programs under gadgetfs or configfs from doing it. Signed-off-by: Alan Stern Reported-and-tested-by: syzbot+8ab8bf161038a8768553@syzkaller.appspotmail.com CC: Acked-by: Felipe Balbi Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281052370.1485-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman

UAS: Revert commit 3ae62a42090f ("UAS: fix alignment of scatter/gather segments")

2019-10-28T16:53:39Z

Commit 3ae62a42090f ("UAS: fix alignment of scatter/gather segments"), copying a similar commit for usb-storage, attempted to solve a problem involving scatter-gather I/O and USB/IP by setting the virt_boundary_mask for mass-storage devices. However, it now turns out that the analogous change in usb-storage interacted badly with commit 09324d32d2a0 ("block: force an unlimited segment size on queues with a virt boundary"), which was added later. A typical error message is: ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes), total 32768 (slots), used 97 (slots) There is no longer any reason to keep the virt_boundary_mask setting in the uas driver. It was needed in the first place only for handling devices with a block size smaller than the maxpacket size and where the host controller was not capable of fully general scatter-gather operation (that is, able to merge two SG segments into a single USB packet). But: High-speed or slower connections never use a bulk maxpacket value larger than 512; The SCSI layer does not handle block devices with a block size smaller than 512 bytes; All the host controllers capable of SuperSpeed operation can handle fully general SG; Since commit ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver") was merged, the USB/IP driver can also handle SG. Therefore all supported device/controller combinations should be okay with no need for any special virt_boundary_mask. So in order to head off potential problems similar to those affecting usb-storage, this patch reverts commit 3ae62a42090f. Signed-off-by: Alan Stern CC: Oliver Neukum CC: Acked-by: Christoph Hellwig Fixes: 3ae62a42090f ("UAS: fix alignment of scatter/gather segments") Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910231132470.1878-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman

usb-storage: Revert commit 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")

2019-10-28T16:52:44Z

Commit 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows") attempted to solve a problem involving scatter-gather I/O and USB/IP by setting the virt_boundary_mask for mass-storage devices. However, it now turns out that this interacts badly with commit 09324d32d2a0 ("block: force an unlimited segment size on queues with a virt boundary"), which was added later. A typical error message is: ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes), total 32768 (slots), used 97 (slots) There is no longer any reason to keep the virt_boundary_mask setting for usb-storage. It was needed in the first place only for handling devices with a block size smaller than the maxpacket size and where the host controller was not capable of fully general scatter-gather operation (that is, able to merge two SG segments into a single USB packet). But: High-speed or slower connections never use a bulk maxpacket value larger than 512; The SCSI layer does not handle block devices with a block size smaller than 512 bytes; All the host controllers capable of SuperSpeed operation can handle fully general SG; Since commit ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver") was merged, the USB/IP driver can also handle SG. Therefore all supported device/controller combinations should be okay with no need for any special virt_boundary_mask. So in order to fix the swiotlb problem, this patch reverts commit 747668dbc061. Reported-and-tested-by: Piergiorgio Sartor Link: https://marc.info/?l=linux-usb&m=157134199501202&w=2 Signed-off-by: Alan Stern CC: Seth Bollinger CC: Fixes: 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows") Acked-by: Christoph Hellwig Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910211145520.1673-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman

usbip: Fix free of unallocated memory in vhci tx

2019-10-28T16:51:06Z

iso_buffer should be set to NULL after use and free in the while loop. In the case of isochronous URB in the while loop, iso_buffer is allocated and after sending it to server, buffer is deallocated. And then, if the next URB in the while loop is not a isochronous pipe, iso_buffer still holds the previously deallocated buffer address and kfree tries to free wrong buffer address. Fixes: ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver") Reported-by: kbuild test robot Reported-by: Julia Lawall Signed-off-by: Suwan Kim Reviewed-by: Julia Lawall Acked-by: Shuah Khan Link: https://lore.kernel.org/r/20191022093017.8027-1-suwan.kim027@gmail.com Signed-off-by: Greg Kroah-Hartman

usb: xhci: fix le32/le64 accessors in debugfs code

2019-10-28T16:47:08Z

It looks like some of the xhci debug code is passing u32 to functions directly from __le32/__le64 fields. Fix this by using le{32,64}_to_cpu() on these to fix the following sparse warnings; xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types) xhci-debugfs.c:205:62: expected unsigned int [usertype] field0 xhci-debugfs.c:205:62: got restricted __le32 xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types) xhci-debugfs.c:206:62: expected unsigned int [usertype] field1 xhci-debugfs.c:206:62: got restricted __le32 ... [Trim down commit message, sparse warnings were similar -Mathias] Cc: # 4.15+ Signed-off-by: Ben Dooks Signed-off-by: Mathias Nyman Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman