linux/include/net/bluetooth, branch v2.6.39

Bluetooth: Fix HCI_RESET command synchronization

2011-03-24T20:04:44Z

We can't send new commands before a cmd_complete for the HCI_RESET command shows up. Reported-by: Mikko Vinni Reported-by: Justin P. Mattock Reported-by: Ed Tomlinson Signed-off-by: Gustavo F. Padovan Tested-by: Justin P. Mattock Tested-by: Mikko Vinni Tested-by: Ed Tomlinson

Bluetooth: Move index to common header in management interface

2011-02-27T19:56:41Z

Most mgmt commands and event are related to hci adapter. Moving index to common header allow to easily use it in command status while reporting errors. For those not related to adapter use MGMT_INDEX_NONE (0xFFFF) as index. Signed-off-by: Szymon Janc Acked-by: Johan Hedberg Signed-off-by: Gustavo F. Padovan

Bluetooth: Add mgmt_auth_failed event

2011-02-21T20:22:44Z

To properly track bonding completion an event to indicate authentication failure is needed. This event will be sent whenever an authentication complete HCI event with a non-zero status comes. It will also be sent when we're acting in acceptor role for SSP authentication in which case the controller will send a Simple Pairing Complete event. Signed-off-by: Johan Hedberg Signed-off-by: Gustavo F. Padovan

Bluetooth: Fix mgmt_pin_code_reply return parameters

2011-02-21T20:22:44Z

The command complete event for mgmt_pin_code_reply & mgmt_pin_code_neg_reply should have the adapter index, Bluetooth address as well as the status. Signed-off-by: Johan Hedberg Signed-off-by: Gustavo F. Padovan

Bluetooth: Add management support for user confirmation request

2011-02-21T20:22:44Z

This patch adds support for the user confirmation (numeric comparison) Secure Simple Pairing authentication method. Signed-off-by: Johan Hedberg Signed-off-by: Gustavo F. Padovan

Bluetooth: Add mgmt_pair_device command

2011-02-21T20:22:43Z

This patch adds a new mgmt_pair_device which can be used to initiate a dedicated bonding procedure. Some extra callbacks are added to the hci_conn struct so that the pairing code can get notified of the completion of the procedure. Signed-off-by: Johan Hedberg Signed-off-by: Gustavo F. Padovan

Bluetooth: Fix some code style issues in hci_core.h

2011-02-17T16:30:04Z

Signed-off-by: Szymon Janc Signed-off-by: Gustavo F. Padovan

Bluetooth: Send LE Connection Update Command

2011-02-16T23:13:21Z

If the new connection update parameter are accepted, the LE master host sends the LE Connection Update Command to its controller informing the new requested parameters. Signed-off-by: Claudio Takahasi Signed-off-by: Gustavo F. Padovan

Bluetooth: Use proper timer for hci command timout

2011-02-16T19:33:26Z

Use proper timer instead of hci command flow control to timeout failed hci commands. Otherwise stack ends up sending commands when flow control is used to block new commands. 2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10 bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000 2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4 Remote Name Request (0x01|0x0019) status 0x00 ncmd 0 2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6 bdaddr 00:16:CF:E1:C7:D7 Signed-off-by: Ville Tervo Signed-off-by: Gustavo F. Padovan

Bluetooth: Add connection parameter update response

2011-02-16T19:33:24Z

Implements L2CAP Connection Parameter Update Response defined in the Bluetooth Core Specification, Volume 3, Part A, section 4.21. Address the LE Connection Parameter Procedure initiated by the slave. Connection Interval Minimum and Maximum have the same range: 6 to 3200. Time = N * 1.25ms. Minimum shall be less or equal to Maximum. The Slave Latency field shall have a value in the range of 0 to ((connSupervisionTimeout / connIntervalMax) - 1). Latency field shall be less than 500. connSupervisionTimeout = Timeout Multiplier * 10 ms. Multiplier field shall have a value in the range of 10 to 3200. Signed-off-by: Claudio Takahasi Signed-off-by: Gustavo F. Padovan