linux/include/net/nfc, branch v3.19

NFC: hci: Add specific hci macro to not create a pipe

2014-12-02T21:48:13Z

Some pipe are only created by other host (different than the Terminal Host). The pipe values will for example be notified by NFC_HCI_ADM_NOTIFY_PIPE_CREATED. Signed-off-by: Christophe Ricard Signed-off-by: Samuel Ortiz

NFC: nci: Add se_io NCI operand

2014-12-02T01:01:21Z

se_io allows to send apdu over the CLF to the embedded Secure Element. Signed-off-by: Christophe Ricard Signed-off-by: Samuel Ortiz

NFC: nci: Update nci_disable_se to run proprietary commands to disable a secure element

2014-12-02T01:01:21Z

Some NFC controller using NCI protocols may need a proprietary commands flow to disable a secure element Signed-off-by: Christophe Ricard Signed-off-by: Samuel Ortiz

NFC: nci: Update nci_enable_se to run proprietary commands to enable a secure element

2014-12-02T01:01:21Z

Some NFC controller using NCI protocols may need a proprietary commands flow to enable a secure element Signed-off-by: Christophe Ricard Signed-off-by: Samuel Ortiz

NFC: nci: Update nci_discover_se to run proprietary commands to discover all available secure element

2014-12-02T01:01:21Z

Some NFC controller using NCI protocols may need a proprietary commands flow to discover all available secure element Signed-off-by: Christophe Ricard Signed-off-by: Samuel Ortiz

NFC: hci: Add se_io HCI operand

2014-12-02T00:49:58Z

se_io allows to send apdu over the CLF to the embedded Secure Element. Signed-off-by: Christophe Ricard Signed-off-by: Samuel Ortiz

NFC: NCI: Configure ATR_RES general bytes

2014-11-28T13:07:51Z

The Target responds to the ATR_REQ with the ATR_RES. Configure the General Bytes in ATR_RES with the first three octets equal to the NFC Forum LLCP magic number, followed by some LLC Parameters TLVs described in section 4.5 of [LLCP]. Signed-off-by: Julien Lefrique Signed-off-by: Samuel Ortiz

NFC: NCI: Handle Target mode activation

2014-11-28T13:07:51Z

Changes: * Extract the Listen mode activation parameters from RF_INTF_ACTIVATED_NTF. * Store the General Bytes of ATR_REQ. * Signal that Target mode is activated in case of an activation in NFC-DEP. * Update the NCI state accordingly. * Use the various constants defined in nfc.h. * Fix the ATR_REQ and ATR_RES maximum size. As per NCI 1.0 and NCI 1.1, the Activation Parameters for both Poll and Listen mode contain all the bytes of ATR_REQ/ATR_RES starting and including Byte 3 as defined in [DIGITAL]. In [DIGITAL], the maximum size of ATR_REQ/ATR_RES is 64 bytes and they are numbered starting from Byte 1. Signed-off-by: Julien Lefrique Signed-off-by: Samuel Ortiz

NFC: NCI: Enable NFC-DEP in Listen A and Listen F

2014-11-28T13:07:51Z

Send LA_SEL_INFO and LF_PROTOCOL_TYPE with NFC-DEP protocol enabled. Configure 212 Kbit/s and 412 Kbit/s bit rates for Listen F. Signed-off-by: Julien Lefrique Signed-off-by: Samuel Ortiz

NFC: digital: Add NFC-DEP Initiator-side ATN Support

2014-11-28T11:39:55Z

When an NFC-DEP Initiator times out when waiting for a DEP_RES from the Target, its supposed to send an ATN to the Target. The Target should respond to the ATN with a similar ATN PDU and the Initiator can then resend the last non-ATN PDU that it sent. No more than 'N(retry,atn)' are to be send where 2 <= 'N(retry,atn)' <= 5. If the Initiator had just sent a NACK PDU when the timeout occurred, it is to continue sending NACKs until 'N(retry,nack)' NACKs have been send. This is described in section 14.12.5.6 of the NFC-DEP Digital Protocol Spec. The digital layer's NFC-DEP code doesn't implement this so add that support. The value chosen for 'N(retry,atn)' is 2. Reviewed-by: Thierry Escande Tested-by: Thierry Escande Signed-off-by: Mark A. Greer Signed-off-by: Samuel Ortiz