linux/include/soc/mscc, branch v6.0

net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset

2022-08-18T04:58:32Z

With so many counter addresses recently discovered as being wrong, it is desirable to at least have a central database of information, rather than two: one through the SYS_COUNT_* registers (used for ndo_get_stats64), and the other through the offset field of struct ocelot_stat_layout elements (used for ethtool -S). The strategy will be to keep the SYS_COUNT_* definitions as the single source of truth, but for that we need to expand our current definitions to cover all registers. Then we need to convert the ocelot region creation logic, and stats worker, to the read semantics imposed by going through SYS_COUNT_* absolute register addresses, rather than offsets of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been SYS_CNT, by the way). Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: mscc: ocelot: make struct ocelot_stat_layout array indexable

2022-08-18T04:58:32Z

The ocelot counters are 32-bit and require periodic reading, every 2 seconds, by ocelot_port_update_stats(), so that wraparounds are detected. Currently, the counters reported by ocelot_get_stats64() come from the 32-bit hardware counters directly, rather than from the 64-bit accumulated ocelot->stats, and this is a problem for their integrity. The strategy is to make ocelot_get_stats64() able to cherry-pick individual stats from ocelot->stats the way in which it currently reads them out from SYS_COUNT_* registers. But currently it can't, because ocelot->stats is an opaque u64 array that's used only to feed data into ethtool -S. To solve that problem, we need to make ocelot->stats indexable, and associate each element with an element of struct ocelot_stat_layout used by ethtool -S. This makes ocelot_stat_layout a fat (and possibly sparse) array, so we need to change the way in which we access it. We no longer need OCELOT_STAT_END as a sentinel, because we know the array's size (OCELOT_NUM_STATS). We just need to skip the array elements that were left unpopulated for the switch revision (ocelot, felix, seville). Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: mscc: ocelot: turn stats_lock into a spinlock

2022-08-18T04:58:31Z

ocelot_get_stats64() currently runs unlocked and therefore may collide with ocelot_port_update_stats() which indirectly accesses the same counters. However, ocelot_get_stats64() runs in atomic context, and we cannot simply take the sleepable ocelot->stats_lock mutex. We need to convert it to an atomic spinlock first. Do that as a preparatory change. Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: mscc: ocelot: fix incorrect ndo_get_stats64 packet counters

2022-08-18T04:58:30Z

Reading stats using the SYS_COUNT_* register definitions is only used by ocelot_get_stats64() from the ocelot switchdev driver, however, currently the bucket definitions are incorrect. Separately, on both RX and TX, we have the following problems: - a 256-1023 bucket which actually tracks the 256-511 packets - the 1024-1526 bucket actually tracks the 512-1023 packets - the 1527-max bucket actually tracks the 1024-1526 packets => nobody tracks the packets from the real 1527-max bucket Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS all track the wrong thing. However this doesn't seem to have any consequence, since ocelot_get_stats64() doesn't use these. Even though this problem only manifests itself for the switchdev driver, we cannot split the fix for ocelot and for DSA, since it requires fixing the bucket definitions from enum ocelot_reg, which makes us necessarily adapt the structures from felix and seville as well. Fixes: 84705fc16552 ("net: dsa: felix: introduce support for Seville VSC9953 switch") Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family") Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support") Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: dsa: felix: keep reference on entire tc-taprio config

2022-07-01T04:18:15Z

In a future change we will need to remember the entire tc-taprio config on all ports rather than just the base time, so use the taprio_offload_get() helper function to replace ocelot_port->base_time with ocelot_port->taprio. Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski

net: dsa: felix: update base time of time-aware shaper when adjusting PTP time

2022-06-19T08:53:59Z

When adjusting the PTP clock, the base time of the TAS configuration will become unreliable. We need reset the TAS configuration by using a new base time. For example, if the driver gets a base time 0 of Qbv configuration from user, and current time is 20000. The driver will set the TAS base time to be 20000. After the PTP clock adjustment, the current time becomes 10000. If the TAS base time is still 20000, it will be a future time, and TAS entry list will stop running. Another example, if the current time becomes to be 10000000 after PTP clock adjust, a large time offset can cause the hardware to hang. This patch introduces a tas_clock_adjust() function to reset the TAS module by using a new base time after the PTP clock adjustment. This can avoid issues above. Due to PTP clock adjustment can occur at any time, it may conflict with the TAS configuration. We introduce a new TAS lock to serialize the access to the TAS registers. Signed-off-by: Xiaoliang Yang Signed-off-by: David S. Miller

net: dsa: felix: tag_8021q preparation for multiple CPU ports

2022-05-23T09:39:55Z

Update the VCAP filters to support multiple tag_8021q CPU ports. TX works using a filter for VLAN ID on the ingress of the CPU port, with a redirect and a VLAN pop action. This can be updated trivially by amending the ingress port mask of this rule to match on all tag_8021q CPU ports. RX works using a filter for ingress port on the egress of the CPU port, with a VLAN push action. Here we need to replicate these filters for each tag_8021q CPU port, and let them all have the same action. This means that the OCELOT_VCAP_ES0_TAG_8021Q_RXVLAN() cookie needs to encode a unique value for every {user port, CPU port} pair it's given. Do this by encoding the CPU port in the upper 16 bits of the cookie, and the user port in the lower 16 bits. Signed-off-by: Vladimir Oltean Signed-off-by: David S. Miller

net: mscc: ocelot: switch from {,un}set to {,un}assign for tag_8021q CPU ports

2022-05-23T09:39:54Z

There is a desire for the felix driver to gain support for multiple tag_8021q CPU ports, but the current model prevents it. This is because ocelot_apply_bridge_fwd_mask() only takes into consideration whether a port is a tag_8021q CPU port, but not whose CPU port it is. We need a model where we can have a direct affinity between an ocelot port and a tag_8021q CPU port. This serves as the basis for multiple CPU ports. Declare a "dsa_8021q_cpu" backpointer in struct ocelot_port which encodes that affinity. Repurpose the "ocelot_set_dsa_8021q_cpu" API to "ocelot_assign_dsa_8021q_cpu" to express the change of paradigm. Note that this change makes the first practical use of the new ocelot_port->index field in ocelot_port_unassign_dsa_8021q_cpu(), where we need to remove the old tag_8021q CPU port from the reserved VLAN range. Signed-off-by: Vladimir Oltean Signed-off-by: David S. Miller

net: dsa: felix: update bridge fwd mask from ocelot lib when changing tag_8021q CPU

2022-05-23T09:39:54Z

Add more logic to ocelot_port_{,un}set_dsa_8021q_cpu() from the ocelot switch lib by encapsulating the ocelot_apply_bridge_fwd_mask() call that felix used to have. This is necessary because the CPU port change procedure will also need to do this, and it's good to reduce code duplication by having an entry point in the ocelot switch lib that does all that is needed. Signed-off-by: Vladimir Oltean Signed-off-by: David S. Miller

net: mscc: ocelot: move ocelot_port_private :: chip_port to ocelot_port :: index

2022-05-12T23:39:18Z

Currently the ocelot switch lib is unaware of the index of a struct ocelot_port, since that is kept in the encapsulating structures of outer drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port). With the upcoming increase in complexity associated with assigning DSA tag_8021q CPU ports to certain user ports, it becomes necessary for the switch lib to be able to retrieve the index of a certain ocelot_port. Therefore, introduce a new u8 to ocelot_port (same size as the chip_port used by the ocelot switchdev driver) and rework the existing code to populate and use it. Signed-off-by: Vladimir Oltean Signed-off-by: Jakub Kicinski