linux/kernel/sched/rt.c, branch v4.14

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

sched: cpufreq: Allow remote cpufreq callbacks

2017-08-01T12:24:53Z

With Android UI and benchmarks the latency of cpufreq response to certain scheduling events can become very critical. Currently, callbacks into cpufreq governors are only made from the scheduler if the target CPU of the event is the same as the current CPU. This means there are certain situations where a target CPU may not run the cpufreq governor for some time. One testcase to show this behavior is where a task starts running on CPU0, then a new task is also spawned on CPU0 by a task on CPU1. If the system is configured such that the new tasks should receive maximum demand initially, this should result in CPU0 increasing frequency immediately. But because of the above mentioned limitation though, this does not occur. This patch updates the scheduler core to call the cpufreq callbacks for remote CPUs as well. The schedutil, ondemand and conservative governors are updated to process cpufreq utilization update hooks called for remote CPUs where the remote CPU is managed by the cpufreq policy of the local CPU. The intel_pstate driver is updated to always reject remote callbacks. This is tested with couple of usecases (Android: hackbench, recentfling, galleryfling, vellamo, Ubuntu: hackbench) on ARM hikey board (64 bit octa-core, single policy). Only galleryfling showed minor improvements, while others didn't had much deviation. The reason being that this patch only targets a corner case, where following are required to be true to improve performance and that doesn't happen too often with these tests: - Task is migrated to another CPU. - The task has high demand, and should take the target CPU to higher OPPs. - And the target CPU doesn't call into the cpufreq governor until the next tick. Based on initial work from Steve Muckle. Signed-off-by: Viresh Kumar Acked-by: Saravana Kannan Acked-by: Peter Zijlstra (Intel) Signed-off-by: Rafael J. Wysocki

sched/rt: Move RT related code from sched/core.c to sched/rt.c

2017-06-23T08:46:45Z

This helps making sched/core.c smaller and hopefully easier to understand and maintain. Signed-off-by: Nicolas Pitre Cc: Linus Torvalds Cc: Peter Zijlstra Cc: Thomas Gleixner Link: http://lkml.kernel.org/r/20170621182203.30626-3-nicolas.pitre@linaro.org Signed-off-by: Ingo Molnar

sched/rt: Minimize rq->lock contention in do_sched_rt_period_timer()

2017-05-23T08:01:34Z

With CONFIG_RT_GROUP_SCHED=y, do_sched_rt_period_timer() sequentially takes each CPU's rq->lock. On a large, busy system, the cumulative time it takes to acquire each lock can be excessive, even triggering a watchdog timeout. If rt_rq->rt_time and rt_rq->rt_nr_running are both zero, this function does nothing while holding the lock, so don't bother taking it at all. Signed-off-by: Dave Kleikamp Signed-off-by: Peter Zijlstra (Intel) Cc: Linus Torvalds Cc: Peter Zijlstra Cc: Thomas Gleixner Link: http://lkml.kernel.org/r/a767637b-df85-912f-ba69-c90ee00a3fb6@oracle.com Signed-off-by: Ingo Molnar

sched/rt: Remove unnecessary condition in push_rt_task()

2017-05-23T08:01:33Z

pick_next_pushable_task(rq) has BUG_ON(rq_cpu != task_cpu(task)) when it returns a task other than NULL, which means that task_cpu(task) must be rq->cpu. So if task == next_task, then task_cpu(next_task) must be rq->cpu as well. Remove the redundant condition and make the code simpler. This way one unnecessary branch and two LOAD operations can be avoided. Signed-off-by: Byungchul Park Signed-off-by: Peter Zijlstra (Intel) Reviewed-by: Steven Rostedt (VMware) Reviewed-by: Juri Lelli Reviewed-by: Daniel Bristot de Oliveira Cc: Cc: Linus Torvalds Cc: Peter Zijlstra Cc: Thomas Gleixner Link: http://lkml.kernel.org/r/1494551143-22219-1-git-send-email-byungchul.park@lge.com Signed-off-by: Ingo Molnar

sched/rt: Add comments describing the RT IPI pull method

2017-03-16T08:41:35Z

While looking into optimizations for the RT scheduler IPI logic, I realized that the comments are lacking to describe it efficiently. It deserves a lengthy description describing its design. Signed-off-by: Steven Rostedt (VMware) Signed-off-by: Peter Zijlstra (Intel) Cc: Andrew Morton Cc: Clark Williams Cc: Daniel Bristot de Oliveira Cc: Linus Torvalds Cc: Mike Galbraith Cc: Peter Zijlstra Cc: Thomas Gleixner Link: http://lkml.kernel.org/r/20170228155030.30c69068@gandalf.local.home [ Small typographical edits. ] Signed-off-by: Ingo Molnar

sched/core: Remove the tsk_nr_cpus_allowed() wrapper

2017-03-02T07:42:24Z

tsk_nr_cpus_allowed() too is a pretty pointless wrapper that is not used consistently and which makes the code both harder to read and longer as well. So remove it - this also shrinks a bit. Acked-by: Linus Torvalds Cc: Mike Galbraith Cc: Peter Zijlstra Cc: Thomas Gleixner Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar

sched/core: Remove the tsk_cpus_allowed() wrapper

2017-03-02T07:42:24Z

So the original intention of tsk_cpus_allowed() was to 'future-proof' the field - but it's pretty ineffectual at that, because half of the code uses ->cpus_allowed directly ... Also, the wrapper makes the code longer than the original expression! So just get rid of it. This also shrinks a bit. Acked-by: Linus Torvalds Cc: Mike Galbraith Cc: Peter Zijlstra Cc: Thomas Gleixner Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar

Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

2017-02-20T20:52:55Z

Pull scheduler updates from Ingo Molnar: "The main changes in this (fairly busy) cycle were: - There was a class of scheduler bugs related to forgetting to update the rq-clock timestamp which can cause weird and hard to debug problems, so there's a new debug facility for this: which uncovered a whole lot of bugs which convinced us that we want to keep the debug facility. (Peter Zijlstra, Matt Fleming) - Various cputime related updates: eliminate cputime and use u64 nanoseconds directly, simplify and improve the arch interfaces, implement delayed accounting more widely, etc. - (Frederic Weisbecker) - Move code around for better structure plus cleanups (Ingo Molnar) - Move IO schedule accounting deeper into the scheduler plus related changes to improve the situation (Tejun Heo) - ... plus a round of sched/rt and sched/deadline fixes, plus other fixes, updats and cleanups" * 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (85 commits) sched/core: Remove unlikely() annotation from sched_move_task() sched/autogroup: Rename auto_group.[ch] to autogroup.[ch] sched/topology: Split out scheduler topology code from core.c into topology.c sched/core: Remove unnecessary #include headers sched/rq_clock: Consolidate the ordering of the rq_clock methods delayacct: Include sched/core: Clean up comments sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds sched/clock: Add dummy clear_sched_clock_stable() stub function sched/cputime: Remove generic asm headers sched/cputime: Remove unused nsec_to_cputime() s390, sched/cputime: Remove unused cputime definitions powerpc, sched/cputime: Remove unused cputime definitions s390, sched/cputime: Make arch_cpu_idle_time() to return nsecs ia64, sched/cputime: Remove unused cputime definitions ia64: Convert vtime to use nsec units directly ia64, sched/cputime: Move the nsecs based cputime headers to the last arch using it sched/cputime: Remove jiffies based cputime sched/cputime, vtime: Return nsecs instead of cputime_t to account sched/cputime: Complete nsec conversion of tick based accounting ...

sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds

2017-02-01T10:01:30Z

We added the 'sched_rr_timeslice_ms' SCHED_RR tuning knob in this commit: ce0dbbbb30ae ("sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice") ... which name suggests to users that it's in milliseconds, while in reality it's being set in milliseconds but the result is shown in jiffies. This is obviously confusing when HZ is not 1000, it makes it appear like the value set failed, such as HZ=100: root# echo 100 > /proc/sys/kernel/sched_rr_timeslice_ms root# cat /proc/sys/kernel/sched_rr_timeslice_ms 10 Fix this to be milliseconds all around. Signed-off-by: Shile Zhang Signed-off-by: Peter Zijlstra (Intel) Cc: Linus Torvalds Cc: Mike Galbraith Cc: Peter Zijlstra Cc: Thomas Gleixner Link: http://lkml.kernel.org/r/1485612049-20923-1-git-send-email-shile.zhang@nokia.com Signed-off-by: Ingo Molnar