linux/tools/objtool, branch v5.7

Merge tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

2020-05-10T18:59:53Z

Pull x86 fixes from Thomas Gleixner: "A set of fixes for x86: - Ensure that direct mapping alias is always flushed when changing page attributes. The optimization for small ranges failed to do so when the virtual address was in the vmalloc or module space. - Unbreak the trace event registration for syscalls without arguments caused by the refactoring of the SYSCALL_DEFINE0() macro. - Move the printk in the TSC deadline timer code to a place where it is guaranteed to only be called once during boot and cannot be rearmed by clearing warn_once after boot. If it's invoked post boot then lockdep rightfully complains about a potential deadlock as the calling context is different. - A series of fixes for objtool and the ORC unwinder addressing variety of small issues: - Stack offset tracking for indirect CFAs in objtool ignored subsequent pushs and pops - Repair the unwind hints in the register clearing entry ASM code - Make the unwinding in the low level exit to usermode code stop after switching to the trampoline stack. The unwind hint is no longer valid and the ORC unwinder emits a warning as it can't find the registers anymore. - Fix unwind hints in switch_to_asm() and rewind_stack_do_exit() which caused objtool to generate bogus ORC data. - Prevent unwinder warnings when dumping the stack of a non-current task as there is no way to be sure about the validity because the dumped stack can be a moving target. - Make the ORC unwinder behave the same way as the frame pointer unwinder when dumping an inactive tasks stack and do not skip the first frame. - Prevent ORC unwinding before ORC data has been initialized - Immediately terminate unwinding when a unknown ORC entry type is found. - Prevent premature stop of the unwinder caused by IRET frames. - Fix another infinite loop in objtool caused by a negative offset which was not catched. - Address a few build warnings in the ORC unwinder and add missing static/ro_after_init annotations" * tag 'x86-urgent-2020-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/unwind/orc: Move ORC sorting variables under !CONFIG_MODULES x86/apic: Move TSC deadline timer debug printk ftrace/x86: Fix trace event registration for syscalls without arguments x86/mm/cpa: Flush direct map alias during cpa objtool: Fix infinite loop in for_offset_range() x86/unwind/orc: Fix premature unwind stoppage due to IRET frames x86/unwind/orc: Fix error path for bad ORC entry type x86/unwind/orc: Prevent unwinding before ORC initialization x86/unwind/orc: Don't skip the first frame for inactive tasks x86/unwind: Prevent false warnings for non-current tasks x86/unwind/orc: Convert global variables to static x86/entry/64: Fix unwind hints in rewind_stack_do_exit() x86/entry/64: Fix unwind hints in __switch_to_asm() x86/entry/64: Fix unwind hints in kernel exit path x86/entry/64: Fix unwind hints in register clearing code objtool: Fix stack offset tracking for indirect CFAs

objtool: Fix infinite loop in find_jump_table()

2020-05-07T15:22:31Z

Kristen found a hang in objtool when building with -ffunction-sections. It was caused by evergreen_pcie_gen2_enable.cold() being laid out immediately before evergreen_pcie_gen2_enable(). Since their "pfunc" is always the same, find_jump_table() got into an infinite loop because it didn't recognize the boundary between the two functions. Fix that with a new prev_insn_same_sym() helper, which doesn't cross subfunction boundaries. Reported-by: Kristen Carlson Accardi Signed-off-by: Josh Poimboeuf Signed-off-by: Peter Zijlstra (Intel) Link: https://lkml.kernel.org/r/378b51c9d9c894dc3294bc460b4b0869e950b7c5.1588110291.git.jpoimboe@redhat.com

objtool: Fix infinite loop in for_offset_range()

2020-04-26T07:28:14Z

Randy reported that objtool got stuck in an infinite loop when processing drivers/i2c/busses/i2c-parport.o. It was caused by the following code: 00000000000001fd : 1fd: 48 b8 00 00 00 00 00 movabs $0x0,%rax 204: 00 00 00 1ff: R_X86_64_64 .rodata-0x8 207: 41 55 push %r13 209: 41 89 f5 mov %esi,%r13d 20c: 41 54 push %r12 20e: 49 89 fc mov %rdi,%r12 211: 55 push %rbp 212: 48 89 d5 mov %rdx,%rbp 215: 53 push %rbx 216: 0f b6 5a 01 movzbl 0x1(%rdx),%ebx 21a: 48 8d 34 dd 00 00 00 lea 0x0(,%rbx,8),%rsi 221: 00 21e: R_X86_64_32S .rodata 222: 48 89 f1 mov %rsi,%rcx 225: 48 29 c1 sub %rax,%rcx find_jump_table() saw the .rodata reference and tried to find a jump table associated with it (though there wasn't one). The -0x8 rela addend is unusual. It caused find_jump_table() to send a negative table_offset (unsigned 0xfffffffffffffff8) to find_rela_by_dest(). The negative offset should have been harmless, but it actually threw for_offset_range() for a loop... literally. When the mask value got incremented past the end value, it also wrapped to zero, causing the loop exit condition to remain true forever. Prevent this scenario from happening by ensuring the incremented value is always >= the starting value. Fixes: 74b873e49d92 ("objtool: Optimize find_rela_by_dest_range()") Reported-by: Randy Dunlap Tested-by: Randy Dunlap Acked-by: Randy Dunlap Signed-off-by: Josh Poimboeuf Signed-off-by: Ingo Molnar Cc: Julien Thierry Cc: Miroslav Benes Cc: Peter Zijlstra Link: https://lore.kernel.org/r/02b719674b031800b61e33c30b2e823183627c19.1587842122.git.jpoimboe@redhat.com

objtool: Fix stack offset tracking for indirect CFAs

2020-04-25T10:22:27Z

When the current frame address (CFA) is stored on the stack (i.e., cfa->base == CFI_SP_INDIRECT), objtool neglects to adjust the stack offset when there are subsequent pushes or pops. This results in bad ORC data at the end of the ENTER_IRQ_STACK macro, when it puts the previous stack pointer on the stack and does a subsequent push. This fixes the following unwinder warning: WARNING: can't dereference registers at 00000000f0a6bdba for ip interrupt_entry+0x9f/0xa0 Fixes: 627fce14809b ("objtool: Add ORC unwind table generation") Reported-by: Vince Weaver Reported-by: Dave Jones Reported-by: Steven Rostedt Reported-by: Vegard Nossum Reported-by: Joe Mario Reviewed-by: Miroslav Benes Signed-off-by: Josh Poimboeuf Signed-off-by: Ingo Molnar Cc: Andy Lutomirski Cc: Jann Horn Cc: Peter Zijlstra Cc: Thomas Gleixner Link: https://lore.kernel.org/r/853d5d691b29e250333332f09b8e27410b2d9924.1587808742.git.jpoimboe@redhat.com

objtool: Fix off-by-one in symbol_by_offset()

2020-04-22T21:14:46Z

Sometimes, WARN_FUNC() and other users of symbol_by_offset() will associate the first instruction of a symbol with the symbol preceding it. This is because symbol->offset + symbol->len is already outside of the symbol's range. Fixes: 2a362ecc3ec9 ("objtool: Optimize find_symbol_*() and read_symbols()") Signed-off-by: Julien Thierry Reviewed-by: Miroslav Benes Signed-off-by: Josh Poimboeuf

objtool: Fix 32bit cross builds

2020-04-22T21:09:50Z

Apparently there's people doing 64bit builds on 32bit machines. Fixes: 74b873e49d92 ("objtool: Optimize find_rela_by_dest_range()") Reported-by: youling257@gmail.com Signed-off-by: Peter Zijlstra (Intel)

objtool: Make BP scratch register warning more robust

2020-04-14T10:24:22Z

If func is NULL, a seg fault can result. This is a theoretical issue which was found by Coverity, ID: 1492002 ("Dereference after null check"). Fixes: c705cecc8431 ("objtool: Track original function across branches") Reported-by: Gustavo A. R. Silva Signed-off-by: Josh Poimboeuf Signed-off-by: Borislav Petkov Link: https://lkml.kernel.org/r/afc628693a37acd287e843bcc5c0430263d93c74.1585761021.git.jpoimboe@redhat.com

objtool: Fix switch table detection in .text.unlikely

2020-04-14T10:06:21Z

If a switch jump table's indirect branch is in a ".cold" subfunction in .text.unlikely, objtool doesn't detect it, and instead prints a false warning: drivers/media/v4l2-core/v4l2-ioctl.o: warning: objtool: v4l_print_format.cold()+0xd6: sibling call from callable instruction with modified stack frame drivers/hwmon/max6650.o: warning: objtool: max6650_probe.cold()+0xa5: sibling call from callable instruction with modified stack frame drivers/media/dvb-frontends/drxk_hard.o: warning: objtool: init_drxk.cold()+0x16f: sibling call from callable instruction with modified stack frame Fix it by comparing the function, instead of the section and offset. Fixes: 13810435b9a7 ("objtool: Support GCC 8's cold subfunctions") Signed-off-by: Josh Poimboeuf Signed-off-by: Borislav Petkov Reviewed-by: Miroslav Benes Acked-by: Peter Zijlstra (Intel) Link: https://lkml.kernel.org/r/157c35d42ca9b6354bbb1604fe9ad7d1153ccb21.1585761021.git.jpoimboe@redhat.com

objtool: Support Clang non-section symbols in ORC generation

2020-04-14T10:03:42Z

When compiling the kernel with AS=clang, objtool produces a lot of warnings: warning: objtool: missing symbol for section .text warning: objtool: missing symbol for section .init.text warning: objtool: missing symbol for section .ref.text It then fails to generate the ORC table. The problem is that objtool assumes text section symbols always exist. But the Clang assembler is aggressive about removing them. When generating relocations for the ORC table, objtool always tries to reference instructions by their section symbol offset. If the section symbol doesn't exist, it bails. Do a fallback: when a section symbol isn't available, reference a function symbol instead. Reported-by: Dmitry Golovin Signed-off-by: Josh Poimboeuf Signed-off-by: Borislav Petkov Tested-by: Nathan Chancellor Reviewed-by: Miroslav Benes Acked-by: Peter Zijlstra (Intel) Link: https://github.com/ClangBuiltLinux/linux/issues/669 Link: https://lkml.kernel.org/r/9a9cae7fcf628843aabe5a086b1a3c5bf50f42e8.1585761021.git.jpoimboe@redhat.com

objtool: Support Clang non-section symbols in ORC dump

2020-04-14T09:59:52Z

Historically, the relocation symbols for ORC entries have only been section symbols: .text+0: sp:sp+8 bp:(und) type:call end:0 However, the Clang assembler is aggressive about stripping section symbols. In that case we will need to use function symbols: freezing_slow_path+0: sp:sp+8 bp:(und) type:call end:0 In preparation for the generation of such entries in "objtool orc generate", add support for reading them in "objtool orc dump". Signed-off-by: Josh Poimboeuf Signed-off-by: Borislav Petkov Reviewed-by: Miroslav Benes Acked-by: Peter Zijlstra (Intel) Link: https://lkml.kernel.org/r/b811b5eb1a42602c3b523576dc5efab9ad1c174d.1585761021.git.jpoimboe@redhat.com