linux/tools/testing/ktest/sample.conf, branch v3.6

ktest: Add MAX_MONITOR_WAIT option

2012-07-19T20:05:42Z

If the console is constantly outputting content, this can cause ktest to get stuck waiting on the monitor to settle down. The option MAX_MONITOR_WAIT is the maximum time (in seconds) for ktest to wait for the console to flush. Signed-off-by: Steven Rostedt

ktest: Add CONFIG_BISECT_CHECK option

2012-07-19T19:26:00Z

The config-bisect can take a bad config and bisect it down to find out what config actually breaks the config. But as all tests will apply a minconfig (defined by a user) to apply before booting, it is possible that the minconfig could actually make the bad config work (minconfigs can disable configs). The end result is that the config bisect test will not find a config that breaks. This can be rather frustrating to the user. The CONFIG_BISECT_CHECK option, when set to 1, will make sure that the bad config (with the minconfig applied) still fails before trying to bisect. And yes, I did get burned by this. Signed-off-by: Steven Rostedt

ktest: Add PRE_INSTALL option

2012-07-19T19:22:05Z

Add the PRE_INSTALL option that will allow a user to specify a shell command to be executed before the install operation executes. Signed-off-by: Steven Rostedt

ktest: Add PRE/POST_KTEST and TEST options

2012-07-19T19:18:27Z

In order to let the user add commands before and after ktest runs, the PRE_KTEST and POST_KTEST options are defined. They hold shell commands that will execute befor ktest runs its first test, as well as when it completed its last test. The PRE_TEST and POST_TEST will be run befor and after (respectively) for a given test. They can either be global (done for all tests) or defined by a single test. Signed-off-by: Steven Rostedt

ktest: Change singular "paranthesis" to plural "parentheses"

2012-05-23T14:19:09Z

Acked-by: Randy Dunlap Signed-off-by: Jesper Juhl Signed-off-by: Steven Rostedt

ktest: Add USE_OUTPUT_MIN_CONFIG to avoid prompt on make_min_config

2012-05-22T04:07:34Z

If the file that OUTPUT_MIN_CONFIG exists then ktest.pl will prompt the user and ask them if the OUTPUT_MIN_CONFIG should be used as the starting point for make_min_config instead of MIN_CONFIG. This is usually the case, and to allow the user to do so, which is helpful if the user is creating different min configs based on tests, and they know one is a superset of another test, they can set USE_OUTPUT_MIN_CONFIG to one, which will prevent kest.pl from prompting to use the OUTPUT_MIN_CONFIG and it will just use it. If USE_OUTPUT_MIN_CONIFG is set to zero, then ktest.pl will continue to use MIN_CONFIG instead. The default is that USE_OUTPUT_MIN_CONFIG is undefined. Signed-off-by: Steven Rostedt

ktest: Add MIN_CONFIG_TYPE to allow making a minum .config that has network

2012-05-21T21:13:40Z

Add a MIN_CONFIG_TYPE that can be set to 'test' or 'boot'. The default is 'boot' which is what make_min_config has done previously: makes a config file that is the minimum needed to boot the target. But when MIN_CONFIG_TYPE is set to 'test', not only must the target boot, but it must also successfully run the TEST. This allows the creation of a config file that is the minimum to boot and also perform ssh to the target, or anything else a developer wants. Signed-off-by: Steven Rostedt

ktest: Add SCP_TO_TARGET_INSTALL option

2012-03-21T12:21:24Z

Currently the option used to scp both the modules to the target as well as the kernel image are the same (SCP_TO_TARGET). But some embedded boards may require them to be different. The modules may need to be put directly on the board, but the kernel image may need to go to a tftpserver. Add the option SCP_TO_TARGET_INSTALL that will allow the user to change the config so that they may have the modules and image got to different machines. Signed-off-by: Steven Rostedt

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest

2012-01-17T01:53:27Z

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest: ktest: Add INGORE_ERRORS to ignore warnings in boot up ktest: Still do reboot even for REBOOT_TYPE = script ktest: Fix compare script to test if options are not documented ktest: Detect typos in option names ktest: Have all values be set by defaults ktest: Change initialization of defaults hash to perl format ktest: Add options SWITCH_TO_GOOD and SWITCH_TO_TEST ktest: Allow overriding bisect test results ktest: Evaluate options before processing them ktest: Evaluate $KERNEL_VERSION in both install and post install ktest: Only ask options needed for install ktest: When creating a new config, ask for BUILD_OPTIONS ktest: Do not ask for some options if the only test is build ktest: Ask for type of test when creating a new config ktest: Allow bisect test to restart where it left off ktest: When creating new config, allow the use of ${THIS_DIR} ktest: Add default for ssh-user, build-target and target-image ktest: Allow success logs to be stored ktest: Save test output

ktest: Add INGORE_ERRORS to ignore warnings in boot up

2012-01-05T02:56:49Z

When testing a kernel that has warnings, ktest.pl will fail the test when it sees the warning. If you need to test the the kernel and want to ignore the errors that are produced, the option IGNORE_ERRORS has been added. When IGNORE_ERRORS is set to something other than 0, it will ignore call traces due to WARN_ON(). Signed-off-by: Steven Rostedt