summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorLines
2024-09-04arm64: dts: layerscape: rename mdio-mux-emi to mdio-mux@<addr>Frank Li-3/+3
Rename node name mdio-mux-emi<n>@<addr> to mdio-mux@<addr>. Fix below warning: arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dtb: board-control@2,0: 'mdio-mux-emi1@54' does not match any of the regexes: '^mdio-mux@[a-f0-9,]+$', 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/board/fsl,fpga-qixis.yaml Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: fsl-ls1012a-frdm: move clock-sc16is7xx under root nodeFrank Li-6/+6
Move fixed clock "clock-sc16is7x" from dspi to root node to fix below warning: arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: serial@0: Unevaluated properties are not allowed ('clock-sc16is7xx' was unexpected) Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: fsl-ls1043a: move "fsl,ls1043a-qdma" ahead "fsl,ls1021a-qdma"Frank Li-1/+1
Move fsl,ls1043a-qdma ahead fallback string fsl,ls1021a-qdma. Fix warning: dma-controller@8380000: compatible: 'oneOf' conditional failed, one must be fixed: ['fsl,ls1021a-qdma', 'fsl,ls1043a-qdma'] is too long Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8-ss-img: remove undocument slot for jpegFrank Li-2/+0
Remove undocument 'slot' property. It is default 0 at driver. We can remove it safely. Fix below warning: arch/arm64/boot/dts/freescale/imx8dx-colibri-iris.dtb: jpegdec@58400000: 'slot' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352: set SION for cmd and data pad of USDHCMarkus Niebel-29/+34
imx93 pad integrate has one issue, refer to ERR052021: ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low drive mode and nominal mode Description: uSDHC PADs have one integration issue. When CMD/DATA lines direction change from output to input, uSDHC controller begin sampling, the integration issue will make input enable signal from uSDHC propagated to the PAD with a long delay, thus the new input value on the pad comes to uSDHC lately. The uSDHC sampled the old input value and the sampling result is wrong. Workaround: Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will propagate input to uSDHC with no delay, so correct value is sampled. This issue will wrongly trigger the start bit when sample the USDHC command response, cause the USDHC trigger command CRC/index/endbit error, which will finally impact the tuning pass window, espically will impact the standard tuning logic, and can't find a correct delay cell to get the best timing. This follows changes made for i.MX93 EVK with commit bb89601282fc ("arm64: dts: imx93-11x11-evk: set SION for cmd and data pad of USDHC") Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxca: add GPIO line namesMarkus Niebel-0/+44
Provide GPIO line names for userspace usage, e.g. libgpiod. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxca: Add ethernet aliasesAlexander Stein-0/+2
They are used by systemd to rename network interfaces to predictable interface names, e.g. end0 & end1. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxca: add missing pad configurationsAlexander Stein-0/+42
- add missing (and currently unused) pad groups - assign muxed GPIO pads for X1 to gpio2 node Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxca: improve pad configurationMarkus Niebel-76/+104
- disable PU/PD if already done with external resistors - do not configure Schmitt Trigger for outputs - do not configure DSE / FSEL for inputs Pad config changes suggested by hardware team. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxca: add RTC / temp sensor IRQMarkus Niebel-0/+29
The IRQ lines from devices on SoM are connected to CPU GPIO on this mainboard. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxla: add GPIO line namesMarkus Niebel-3/+52
Provide GPIO line names for userspace usage, e.g. libgpiod. While at it, correct the line-name property for ENET[1,2]_INT# gpio hog and LCD_BLT_EN. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxla: Add ethernet aliasesAlexander Stein-0/+2
They are used by systemd to rename network interfaces to predictable interface names, e.g. end0 & end1. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxla: add missing pad configurationsAlexander Stein-0/+48
- add missing (and currently unused) pad groups - assign muxed GPIO pads for X1 to gpio2 node Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxla: add irq for temp sensorMarkus Niebel-1/+16
This adds muxing and configuration of the irq output of the temp sensor on TQMa93xx that is connected to a GPIO line on MBa93xxLA While at it, add comment for RTC_EVENT for pcf85063 since the IRQ line of both devices on SoM are routed to CPU GPIO on MBa93xxLA. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxla: enable LPSPI6 interfaceAlexander Stein-0/+24
LPSPI6 features a NAFE13388 analog frontend. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352-mba93xxla: improve pad configurationMarkus Niebel-73/+97
- disable PU/PD if already done with external resistors - do not configure Schmitt Trigger for outputs - do not configure DSE / FSEL for inputs Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352: add eMMC regulatorsAlexander Stein-0/+2
With PMIC node in place, add the correct regulators for eMMC. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: freescale: imx93-tqma9352: Add PMIC nodeAlexander Stein-21/+92
With driver support in place add the PMIC node and remove the fixed-regulators for rails provided by PMIC. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mm: Update Data Modul i.MX8M Mini eDM SBC DT to rev.A01Marek Vasut-2/+17
Update the DT to match newest Data Modul i.MX8M Mini eDM SBC rev.A01 board which implements PHY changes. Keep some of the rev.900 PHY node in the DT so that a DTO can be used to support rev.900 boards easily. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp: Enable HDMI to Data Modul i.MX8M Plus eDM SBCMarek Vasut-0/+46
Enable HDMI support on Data Modul i.MX8M Plus eDM SBC. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp: Add DT nodes for the two ISPsPaul Elder-2/+55
The ISP supports both CSI and parallel interfaces, where port 0 corresponds to the former and port 1 corresponds to the latter. Since the i.MX8MP's ISPs are connected by the parallel interface to the CSI receiver, set them both to port 1. Signed-off-by: Paul Elder <paul.elder@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mm-phygate-tauri-l: add rtc aux-voltage-chargeableYannic Moog-0/+1
phygate-tauri-l has a chargable capacitor populated, rtc supports charging it. Add property indicating this. Signed-off-by: Yannic Moog <y.moog@phytec.de> Reviewed-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mm-phyboard-polis: add rtc aux-voltage-chargeableYannic Moog-0/+1
phyboard-polis has a chargable capacitor populated, rtc supports charging it. Add property indicating this. Signed-off-by: Yannic Moog <y.moog@phytec.de> Reviewed-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp-phyboard-pollux: add rtc aux-voltage-chargeableYannic Moog-0/+1
phyboard-pollux has a chargable capacitor populated, rtc supports charging it. Add property indicating this. Signed-off-by: Yannic Moog <y.moog@phytec.de> Reviewed-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp-phyboard-pollux: Add usb3_phy1 regulator referenceYashwanth Varakala-0/+1
Add VCC_5V_SW regulator reference to the usb1 phy node to reflect the schematic. This also silences the fallback dummy regulator warning. Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de> Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp-phyboard-pollux: Add VCC_5V_SW regulatorYashwanth Varakala-0/+9
Add fixed regulator VCC_5V_SW based on the phyBOARD-Pollux schematics to reflect the connectivity on the phyBOARD-Pollux-i.MX8MP. Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de> Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp-phyboard-pollux: Assign regulator to EEPROM nodeYashwanth Varakala-0/+1
Add VCC_3V3_SW regulator reference to the EEPROM node to reflect the schematic. This also silences the fallback dummy regulator warning. Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de> Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp-phyboard-pollux: Add SD-Card vqmmc supplyTeresa Remmet-0/+1
Add SD-Card property for the bus IO power from the PMIC. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp-phycore: Assign regulator to EEPROM nodeYashwanth Varakala-0/+1
Add VDD_IO regulator reference to the EEPROM node to reflect the schematic. This also silences the fallback dummy regulator warning. Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de> Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp-phycore: Add VDD_IO regulatorYashwanth Varakala-0/+9
Add fixed regulator VDD_IO (3.3v) based on the SoM schematics to reflect the connectivity on the phyCORE-i.MX8MP. Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de> Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Yannic Moog <y.moog@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: imx8mp: Clarify csis clock frequencyLaurent Pinchart-6/+4
The DT nodes for the MIPI CSI-2 receivers (MIPI_CSI) configure the CAM1_PIX and CAM2_PIX clocks to 266 MHz through the assigned-clock-rates property, and report that frequency in the clock-frequency property. The i.MX8MP reference manual and datasheet list 266 MHz as a nominal frequency when using both CSI-2 receivers, so all looks normal. In reality, the clock is actually set to 250 MHz, as the selected parent, IMX8MP_SYS_PLL2_1000M, has a 1/4 output that is selected as the closest frequency to 266 MHz. This doesn't break operation of the device, but is clearly misleading. Clarify the clock configuration by selecting the IMX8MP_SYS_PLL2_250M parent, dropping the redundant assigned-clock-rates, and setting clock-frequency to 250 MHz. This doesn't cause any functional change. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-09-04arm64: dts: Add support for Kontron i.MX93 OSM-S SoM and BL carrier boardFrieder Schrempf-0/+792
This adds support for the Kontron Electronics OSM-S i.MX93 SoM and the matching baseboard BL i.MX93. The SoM hardware complies to the Open Standard Module (OSM) 1.1 specification, size S (https://sget.org/standards/osm). Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-28arm64: dts: mba8mx: Add Ethernet PHY IRQ supportAlexander Stein-0/+2
The interrupt pin of the PHY is connected to the GPIO expander, configure it accordingly. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-28arm64: dts: layerscape: remove unused num-viewportAnimesh Agarwal-1/+0
Remove unused property num-viewport to fix dtbs warnings. arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dtb: pcie@3400000: Unevaluated properties are not allowed ('num-viewport' was unexpected) from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml# arch/arm64/boot/dts/freescale/fsl-ls1012a-oxalis.dtb: pcie@3400000: Unevaluated properties are not allowed ('num-viewport' was unexpected) from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml# Cc: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Animesh Agarwal <animeshagarwal28@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: freescale: imx8mp-phyboard-pollux: Add and enable TPMBenjamin Hahn-0/+25
Add support for TPM for phyBOARD Pollux. Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx93: add lpi2c1 and st lsm6dso nodeClark Wang-0/+19
The i.MX93 11x11 EVK has a ST LSM6DSO connected to I2C, which a is 6-axis IMU (inertial measurement unit = accelerometer & gyroscope). So add the missing parts to the DTS file. Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Reviewed-by: Haibo Chen <haibo.chen@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx93-tqma9352-mba93: Fix USB hub node nameFabio Estevam-2/+2
According to microchip,usb2514.yaml, the node name must contain 'usb-hub'. Change it accordingly to fix the following dt-schema warning: hub@1: $nodename:0: 'hub@1' does not match '^usb(@.*)?' Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx8mm/n-beacon-kit: Fix the order of ADV7535 reg entriesFabio Estevam-4/+4
According to adi,adv7533.yaml, the order for the reg and reg-names entries must be: main, edid, cec, and packet. Fix it accordingly to remove the following dt-schema warnings: hdmi@3d: reg-names:1: 'edid' was expected hdmi@3d: reg-names:2: 'cec' was expected Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx8mp-venice-gw74xx-imx219: remove compatible in overlay fileFrank Li-2/+0
Remove compatible string in overlay file to fix below warning: gw,imx8mp-gw74xx' is not one of ['fsl,ls1043a-rdb', 'fsl,ls1043a-qds'] Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx8mp-data-modul-edm-sbc: remove #clock-cells for sai3Frank Li-1/+0
Remove #clock-cells for sai3 because sai3 is not clock controller to fix below warning: /arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dtb: sai@30c30000: Unevaluated properties are not allowed ('#clock-cells' was unexpected) Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx8mm-venice-gw7901: add #address(size)-cells for gsc@20Frank Li-0/+2
Add #address-cells and #size-cells for gsc@20 to fix below warning: arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dtb: gsc@20: '#address-cells' is a required propert Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: fsl-ls208xa: move reboot node under sysconFrank Li-7/+6
Move reboot node under syscon and change compatible string to fsl,ls1028a-rstcr because it is exactly same as ls1028a. Fix below warning: arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dtb: /syscon@1e60000: failed to match any schema with compatible: ['fsl,ls2080a-rstcr', 'syscon'] Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: fsl-ls1028a: remove undocumented 'little-endian' for dspi nodeFrank Li-3/+0
According to binding doc http://devicetree.org/schemas/spi/fsl,dspi.yaml and driver drivers/spi/spi-fsl-dspi.c, default is little-endian, should use big-endian for big-endian system. Remove 'little-endian' to fix below warning: arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dtb: spi@2100000: Unevaluated properties are not allowed ('little-endian' was unexpected) Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx8mp-verdin: add HDMI audio supportJoão Paulo Gonçalves-0/+48
Add native HDMI audio to Verdin iMX8MP and all its carriers boards. Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx95: add flexcan[1..5] supportHaibo Chen-0/+70
Add the flexcan[1..5] nodes for imx95. Reviewed-by: Han Xu <han.xu@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: imx95: add DDR Perf Monitor nodeXu Yang-0/+6
Add DDR Perf Monitor for i.MX95. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: fsl,ls2085a: remove fsl,ls2085a-pcieFrank Li-4/+4
fsl,ls2080a-pcie actual is the same as fsl,ls2085a-pcie. Only keep one is enough, so remove "fsl,ls2085a-pcie" to fix below warnings. arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dtb: pcie@3400000: compatible: ['fsl,ls2080a-pcie', 'fsl,ls2085a-pcie'] is too long from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml# Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: layerscape: remove undocumented fsl,ls-pcie-epFrank Li-6/+6
Remove undocumented compatible string fsl,ls-pcie-ep to fix below CHECK_DTBS warning. arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dtb: pcie_ep@3400000: compatible: ['fsl,ls1046a-pcie-ep', 'fsl,ls-pcie-ep'] is too long from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie-ep.yaml Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: fsl-ls1046a: remove big-endian at memory-controllerFrank Li-2/+0
According to binding doc fsl,ddr.yaml, big-endian is default setting. So remove it to fix below CHECK_DTBS warnings. arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: memory-controller@1080000: 'big-endian' does not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,ddr.yaml Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-08-13arm64: dts: layerscape: remove big-endian for mmc nodesFrank Li-5/+0
According to binding doc fsl,esdhc.yaml, the default endian mode is big-endian. So remove big-endian property to fix below CHECK_DTBS warnings: arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: mmc@1560000: Unevaluated properties are not allowed ('big-endian' was unexpected) from schema $id: http://devicetree.org/schemas/mmc/fsl,esdhc.yaml Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
generated by cgit v1.2.3 (git 2.46.0) at 2026-05-26 23:09:05 +0000