| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
irq_data->hwirq is unsigned long. This fixes GCC warning:
drivers/irqchip/irq-s3c24xx.c: In function 's3c_irqext0_type':
drivers/irqchip/irq-s3c24xx.c:253:19: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if ((data->hwirq >= 0) && (data->hwirq <= 3)) {
^~
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
If there are any errors in stm32_exti_host_init() then it leads to a
NULL dereference in the callers. The function should clean up after
itself.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
When compiling bmips with SMP disabled, the build fails with:
drivers/irqchip/irq-bcm7038-l1.o: In function `bcm7038_l1_cpu_offline':
drivers/irqchip/irq-bcm7038-l1.c:242: undefined reference to `irq_set_affinity_locked'
make[5]: *** [vmlinux] Error 1
Fix this by adding and setting bcm7038_l1_cpu_offline only when actually
compiling for SMP. It wouldn't have been used anyway, as it requires
CPU_HOTPLUG, which in turn requires SMP.
Fixes: 34c535793bcb ("irqchip/bcm7038-l1: Implement irq_cpu_offline() callback")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The its_lock lock is held while a new device is added to the list and
during setup while the CPU is booted. Even on -RT the CPU-bootup is
performed with disabled interrupts.
Make its_lock a raw_spin_lock_t.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Allocating a minimum of 32 LPIs per PCI device, let's reduce it to
be just 1, as most devices do not need that many interrupts.
We still have to special-case DevID 0, as there is plenty of broken
HW around where the PCI RID is not presented as a DevID to the ITS,
and all the devices are presented as DevID 0. In this case, we keep
the 32 minimal allocation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
A recent extension to the GIC architecture allows a hypervisor to
arbitrarily reduce the number of LPIs available to a guest, no
matter what the GIC says about the valid range of IntIDs.
Let's factor in this information when computing the number of
available LPIs
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Instead of exposing the GIC distributor IntID field in the rdist
structure that is passed to the ITS, let's replace it with a
copy of the whole GICD_TYPER register. We are going to need
some of this information at a later time.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The chunk allocation system is now officially dead, so let's
remove it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
At the moment, the core ITS driver imposes the allocation to be
in chunks of 32. As we want to relax this on a per bus basis, let's
move the the the allocation constraints to each bus.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
As we used to represent the LPI range using a bitmap, we were reducing
the number of LPIs to at most 64k in order to preserve memory.
With our new allocator, there is no such need, as dealing with 2^16
or 2^32 LPIs takes the same amount of memory.
So let's use the number of IntID bits reported by the GIC instead of
an arbitrary limit.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Our current LPI allocator relies on a bitmap, each bit representing
a chunk of 32 LPIs, meaning that each device gets allocated LPIs
in multiple of 32. It served us well so far, but new use cases now
require much more finer grain allocations, down the the individual
LPI.
Given the size of the IntID space (up to 32bit), it isn't practical
to continue using a bitmap, so let's use a different data structure
altogether.
We switch to a list, where each element represent a contiguous range
of LPIs. On allocation, we simply grab the first group big enough to
satisfy the allocation, and substract what we need from it. If the
group becomes empty, we just remove it. On freeing interrupts, we
insert a new group of interrupt in the list, sort it and fuse the
adjacent groups.
This makes freeing interrupt much more expensive than allocating
them (an unusual behaviour), but that's fine as long as we consider
that freeing interrupts is an extremely rare event.
We still allocate interrupts in blocks of 32 for the time being,
but subsequent patches will relax this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for 4.18:
- an important core fix for RTCs using the core offsetting only one
driver is affected
- a fix for the error path of mrst"
* tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: fix alarm read and set offset
rtc: mrst: fix error code in probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"A clocksource driver fix and a revert"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: arm_arch_timer: Set arch_mem_timer cpumask to cpu_possible_mask
Revert "tick: Prefer a lower rating device only if it's CPU local device"
|
|
Pull rdma fixes from Jason Gunthorpe:
"Things have been quite slow, only 6 RC patches have been sent to the
list. Regression, user visible bugs, and crashing fixes:
- cxgb4 could wrongly fail MR creation due to a typo
- various crashes if the wrong QP type is mixed in with APIs that
expect other types
- syzkaller oops
- using ERR_PTR and NULL together cases HFI1 to crash in some cases
- mlx5 memory leak in error unwind"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
RDMA/uverbs: Don't fail in creation of multiple flows
IB/hfi1: Fix incorrect mixing of ERR_PTR and NULL return values
RDMA/uverbs: Fix slab-out-of-bounds in ib_uverbs_ex_create_flow
RDMA/uverbs: Protect from attempts to create flows on unsupported QP
iw_cxgb4: correctly enforce the max reg_mr depth
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dave Jiang:
- ensure that a variable passed in by reference to acpi_nfit_ctl is
always set to a value. An incremental patch is provided due to notice
from testing in -next. The rest of the commits did not exhibit
issues.
- fix a return path in nsio_rw_bytes() that was not returning "bytes
remain" as expected for the function.
- address an issue where applications polling on scrub-completion for
the NVDIMM may falsely wakeup and read the wrong state value and
cause hang.
- change the test unit persistent capability attribute to fix up a
broken assumption in the unit test infrastructure wrt the
'write_cache' attribute
- ratelimit dev_info() in the dax device check_vma() function since
this is easily triggered from userspace
* tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix unchecked dereference in acpi_nfit_ctl
acpi, nfit: Fix scrub idle detection
tools/testing/nvdimm: advertise a write cache for nfit_test
acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value
dev-dax: check_vma: ratelimit dev_info-s
libnvdimm, pmem: Fix memcpy_mcsafe() return code handling in nsio_rw_bytes()
|
|
The offset needs to be added after reading the alarm value.
It also needs to be subtracted after the now < alarm test.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I2C clients may misunderstand recovery pulses if they can't read SDA to
bail out early. In the worst case, as a write operation. To avoid that
and if we can write SDA, try to send STOP to avoid the
misinterpretation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Pull MTD fix from Boris Brezillon:
"A SPI NOR fix to fix a timeout in the cadence QSPI controller driver"
* tag 'mtd/fixes-for-4.18-rc5' of git://git.infradead.org/linux-mtd:
mtd: spi-nor: cadence-quadspi: Fix direct mode write timeouts
|
|
Fix memory leak in the error path of mlx5_ib_create_srq() by making sure
to free the allocated srq.
Fixes: c2b37f76485f ("IB/mlx5: Fix integer overflows in mlx5_ib_create_srq")
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
- Jens's patches to expand the usable command depth from 31 to 32 broke
sata_fsl due to a subtle command iteration bug. Fixed by introducing
explicit iteration helpers and using the correct variant.
- On some laptops, enabling LPM by default reportedly led to occasional
hard hangs. Blacklist the affected cases.
- Other misc fixes / changes.
* 'for-4.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: Remove depends on HAS_DMA in case of platform dependency
ata: Fix ZBC_OUT all bit handling
ata: Fix ZBC_OUT command block check
ahci: Add Intel Ice Lake LP PCI ID
ahci: Disable LPM on Lenovo 50 series laptops with a too old BIOS
sata_nv: remove redundant pointers sdev0 and sdev1
sata_fsl: remove dead code in tag retrieval
sata_fsl: convert to command iterator
libata: convert eh to command iterators
libata: add command iterator helpers
ata: ahci_mvebu: ahci_mvebu_stop_engine() can be static
libahci: Fix possible Spectre-v1 pmp indexing in ahci_led_store()
|
|
Incremental patch to fix the unchecked dereference in acpi_nfit_ctl.
Reported by Dan Carpenter:
"acpi/nfit: fix cmd_rc for acpi_nfit_ctl to
always return a value" from Jun 28, 2018, leads to the following
Smatch complaint:
drivers/acpi/nfit/core.c:578 acpi_nfit_ctl()
warn: variable dereferenced before check 'cmd_rc' (see line 411)
drivers/acpi/nfit/core.c
410
411 *cmd_rc = -EINVAL;
^^^^^^^^^^^^^^^^^^
Patch adds unchecked dereference.
Fixes: c1985cefd844 ("acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are a few char/misc driver fixes for 4.18-rc5.
The "largest" stuff here is fixes for the UIO changes in 4.18-rc1 that
caused breakages for some people. Thanks to Xiubo Li for fixing them
quickly. Other than that, minor fixes for thunderbolt, vmw_balloon,
nvmem, mei, ibmasm, and mei drivers. There's also a MAINTAINERS update
where Rafael is offering to help out with reviewing driver core
patches.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
nvmem: Don't let a NULL cell_id for nvmem_cell_get() crash us
thunderbolt: Notify userspace when boot_acl is changed
uio: fix crash after the device is unregistered
uio: change to use the mutex lock instead of the spin lock
uio: use request_threaded_irq instead
fpga: altera-cvp: Fix an error handling path in 'altera_cvp_probe()'
ibmasm: don't write out of bounds in read handler
MAINTAINERS: Add myself as driver core changes reviewer
mei: discard messages from not connected client during power down.
vmw_balloon: fix inflation with batching
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are two tiny staging driver fixes for reported issues for
4.18-rc5.
One fixes the r8822be driver to properly work on lots of new laptops,
the other is for the rtl8723bs driver to fix an underflow error.
Both have been in linux-next for a while with no reported issues"
* tag 'staging-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8822be: Fix RTL8822be can't find any wireless AP
staging: rtl8723bs: Prevent an underflow in rtw_check_beacon_data().
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.18-rc5.
Nothing major here, just the normal set of new device ids, xhci fixes,
and some typec fixes. The typec fix required some tiny changes in an
i2c driver, which that maintainer acked to come through my tree.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: yurex: fix out-of-bounds uaccess in read handler
usb: quirks: add delay quirks for Corsair Strafe
xhci: xhci-mem: off by one in xhci_stream_id_to_ring()
usb/gadget: aspeed-vhub: add USB_LIBCOMPOSITE dependency
docs: kernel-parameters.txt: document xhci-hcd.quirks parameter
USB: serial: mos7840: fix status-register error handling
USB: serial: keyspan_pda: fix modem-status error handling
USB: serial: cp210x: add another USB ID for Qivicon ZigBee stick
USB: serial: ch341: fix type promotion bug in ch341_control_in()
i2c-cht-wc: Fix bq24190 supplier
typec: tcpm: Correctly report power_supply current and voltage for non pd supply
usb: xhci: dbc: Don't decrement runtime PM counter if DBC is not started
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fixup devname in /proc/interrupts for card detect GPIO
MMC host:
- sdhci-esdhc-imx: Allow 1.8V speed-modes without 100/200MHz pinctrls
- sunxi: Disable IRQ in low power state to prevent IRQ storm
- dw_mmc: Fix card threshold control configuration
- renesas_sdhi_internal_dmac: Fixup DMA error paths"
* tag 'mmc-v4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-esdhc-imx: allow 1.8V modes without 100/200MHz pinctrl states
mmc: sunxi: Disable irq during pm_suspend
mmc: dw_mmc: fix card threshold control configuration
mmc: core: cd_label must be last entry of mmc_gpio struct
mmc: renesas_sdhi_internal_dmac: Cannot clear the RX_IN_USE in abort
mmc: renesas_sdhi_internal_dmac: Fix missing unmap in error patch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Address a regression in ACPICA that ceased to clear the status of GPEs
and fixed events before entering the ACPI S5 (off) system state during
the 4.17 cycle which caused some systems to power up immediately after
they had been turned off"
* tag 'acpi-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Clear status of all events when entering S5
|
|
Currently, arch_mem_timer cpumask is set to cpu_all_mask which should be
fine. However, cpu_possible_mask is more accurate and if there are other
clockevent source in the system which are set to cpu_possible_mask, then
having cpu_all_mask may result in issue.
E.g. on a platform with arm,sp804 timer with rating 300 and
cpu_possible_mask and this arch_mem_timer timer with rating 400 and
cpu_all_mask, tick_check_preferred may choose both preferred as the
cpumasks are not equal though they must be.
This issue was root caused incorrectly initially and a fix was merged as
commit 1332a9055801 ("tick: Prefer a lower rating device only if it's CPU
local device").
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/1531151136-18297-2-git-send-email-sudeep.holla@arm.com
|
|
Pull drm fixes from Dave Airlie:
"This just contains some etnaviv fixes and a MAINTAINERS update for the
new drm tree locations"
* tag 'drm-fixes-2018-07-10' of git://anongit.freedesktop.org/drm/drm:
MAINTAINERS: update drm tree
drm/etnaviv: bring back progress check in job timeout handler
drm/etnaviv: Fix driver unregistering
drm/etnaviv: Check for platform_device_register_simple() failure
|
|
into drm-fixes
Lucas wrote:
"a couple of small fixes:
- 2 patches from Fabio to fix module reloading
- one patch to fix a userspace visible regression, where the job
timeout is a bit too eager and kills legitimate jobs"
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530868450.15725.8.camel@pengutronix.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- spectrev1 pattern fix in hiddev from Gustavo A. R. Silva
- bounds check fix for hid-debug from Daniel Rosenberg
- regression fix for HID autobinding from Benjamin Tissoires
- removal of excessive logging from i2c-hid driver from Jason Andryuk
- fix specific to 2nd generation of Wacom Intuos devices from Jason
Gerecke
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hiddev: fix potential Spectre v1
HID: i2c-hid: Fix "incomplete report" noise
HID: wacom: Correct touch maximum XY of 2nd-gen Intuos
HID: debug: check length before copy_to_user()
HID: core: allow concurrent registration of drivers
|
|
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678f9 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d08338 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678f9 was made we now disable 'packet
mode' before the delay from commit f70893d08338 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678f9 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
|
|
uref->field_index, uref->usage_index, finfo.field_index and cinfo.index can be
indirectly controlled by user-space, hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/hid/usbhid/hiddev.c:473 hiddev_ioctl_usage() warn: potential spectre issue 'report->field' (local cap)
drivers/hid/usbhid/hiddev.c:477 hiddev_ioctl_usage() warn: potential spectre issue 'field->usage' (local cap)
drivers/hid/usbhid/hiddev.c:757 hiddev_ioctl() warn: potential spectre issue 'report->field' (local cap)
drivers/hid/usbhid/hiddev.c:801 hiddev_ioctl() warn: potential spectre issue 'hid->collection' (local cap)
Fix this by sanitizing such structure fields before using them to index
report->field, field->usage and hid->collection
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit ac75a041048b ("HID: i2c-hid: fix size check and type usage") started
writing messages when the ret_size is <= 2 from i2c_master_recv. However, my
device i2c-DLL07D1 returns 2 for a short period of time (~0.5s) after I stop
moving the pointing stick or touchpad. It varies, but you get ~50 messages
each time which spams the log hard.
[ 95.925055] i2c_hid i2c-DLL07D1:01: i2c_hid_get_input: incomplete report (83/2)
This has also been observed with a i2c-ALP0017.
[ 1781.266353] i2c_hid i2c-ALP0017:00: i2c_hid_get_input: incomplete report (30/2)
Only print the message when ret_size is totally invalid and less than 2 to cut
down on the log spam.
Fixes: ac75a041048b ("HID: i2c-hid: fix size check and type usage")
Reported-by: John Smith <john-s-84@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7da ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After commit 18996f2db918 (ACPICA: Events: Stop unconditionally
clearing ACPI IRQs during suspend/resume) the status of ACPI events
is not cleared any more when entering the ACPI S5 system state (power
off) which causes some systems to power up immediately after turing
off power in certain situations.
That is a functional regression, so address it by making the code
clear the status of all ACPI events again when entering S5 (for
system-wide suspend or hibernation the clearing of the status of all
events is not desirable, as it might cause the kernel to miss wakeup
events sometimes).
Fixes: 18996f2db918 (ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume)
Reported-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Thomas Hänig <haenig@cosifan.de>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small collection of fixes, sort of the usual at this point, all for
i.MX or OMAP:
- Enable ULPI drivers on i.MX to avoid a hang
- Pinctrl fix for touchscreen on i.MX51 ZII RDU1
- Fixes for ethernet clock references on am3517
- mmc0 write protect detection fix for am335x
- kzalloc->kcalloc conversion in an OMAP driver
- USB metastability fix for USB on dra7
- Fix touchscreen wakeup on am437x"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx_v4_v5_defconfig: Select ULPI support
ARM: imx_v6_v7_defconfig: Select ULPI support
ARM: dts: omap3: Fix am3517 mdio and emac clock references
ARM: dts: am335x-bone-common: Fix mmc0 Write Protect
bus: ti-sysc: Use 2-factor allocator arguments
ARM: dts: dra7: Disable metastability workaround for USB2
ARM: dts: imx51-zii-rdu1: fix touchscreen pinctrl
ARM: dts: am437x: make edt-ft5x06 a wakeup source
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix a use-after-free in the endpoint code (Dan Carpenter)
- Stop defaulting CONFIG_PCIE_DW_PLAT_HOST to yes (Geert Uytterhoeven)
- Fix an nfp regression caused by a change in how we limit the number
of VFs we can enable (Jakub Kicinski)
- Fix failure path cleanup issues in the new R-Car gen3 PHY support
(Marek Vasut)
- Fix leaks of OF nodes in faraday, xilinx-nwl, xilinx (Nicholas Mc
Guire)
* tag 'pci-v4.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
nfp: stop limiting VFs to 0
PCI/IOV: Reset total_VFs limit after detaching PF driver
PCI: faraday: Add missing of_node_put()
PCI: xilinx-nwl: Add missing of_node_put()
PCI: xilinx: Add missing of_node_put()
PCI: endpoint: Use after free in pci_epf_unregister_driver()
PCI: controller: dwc: Do not let PCIE_DW_PLAT_HOST default to yes
PCI: rcar: Clean up PHY init on failure
PCI: rcar: Shut the PHY down in failpath
|
|
Pull dma-mapping fix from Christoph Hellwig:
"Revert an incorrect dma-mapping commit for 4.18-rc"
* tag 'dma-mapping-4.18-3' of git://git.infradead.org/users/hch/dma-mapping:
Revert "iommu/intel-iommu: Enable CONFIG_DMA_DIRECT_OPS=y and clean up intel_{alloc,free}_coherent()"
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We have few odd driver fixes and one email update change for you this
time:
- Driver fixes for k3dma (off by one), pl330 (burst residue
granularity) and omap-dma (incorrect residue_granularity)
- Sinan's email update"
* tag 'dmaengine-fix-4.18-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: k3dma: Off by one in k3_of_dma_simple_xlate()
dmaengine: pl330: report BURST residue granularity
MAINTAINERS: Update email-id of Sinan Kaya
dmaengine: ti: omap-dma: Fix OMAP1510 incorrect residue_granularity
|
|
Pull IPMI fixes from Corey Minyard:
"A couple of small fixes: one to the BMC side of things that fixes an
interrupt issue, and one oops fix if init fails in a certain way on
the client driver"
* tag 'for-linus-4.18-2' of git://github.com/cminyard/linux-ipmi:
ipmi: kcs_bmc: fix IRQ exception if the channel is not open
ipmi: Cleanup oops on initialization failure
|
|
In commit ca04d9d3e1b1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on
Qcom chips") you can see a call like:
devm_nvmem_cell_get(dev, NULL);
Note that the cell ID passed to the function is NULL. This is because
the qcom-qusb2 driver is expected to work only on systems where the
PHY node is hooked up via device-tree and is nameless.
This works OK for the most part. The first thing nvmem_cell_get()
does is to call of_nvmem_cell_get() and there it's documented that a
NULL name is fine. The problem happens when the call to
of_nvmem_cell_get() returns -EINVAL. In such a case we'll fall back
to nvmem_cell_get_from_list() and eventually might (if nvmem_cells
isn't an empty list) crash with something that looks like:
strcmp
nvmem_find_cell
__nvmem_device_get
nvmem_cell_get_from_list
nvmem_cell_get
devm_nvmem_cell_get
qusb2_phy_probe
There are several different ways we could fix this problem:
One could argue that perhaps the qcom-qusb2 driver should be changed
to use of_nvmem_cell_get() which is allowed to have a NULL name. In
that case, we'd need to add a patche to introduce
devm_of_nvmem_cell_get() since the qcom-qusb2 driver is using devm
managed resources.
One could also argue that perhaps we could just add a name to
qcom-qusb2. That would be OK but I believe it effectively changes the
device tree bindings, so maybe it's a no-go.
In this patch I have chosen to fix the problem by simply not crashing
when a NULL cell_id is passed to nvmem_cell_get().
NOTE: that for the qcom-qusb2 driver the "nvmem-cells" property is
defined to be optional and thus it's expected to be a common case that
we would hit this crash and this is more than just a theoretical fix.
Fixes: ca04d9d3e1b1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit 9aaa3b8b4c56 ("thunderbolt: Add support for preboot ACL")
introduced boot_acl attribute but missed the fact that now userspace
needs to poll the attribute constantly to find out whether it has
changed or not. Fix this by sending notification to the userspace
whenever the boot_acl attribute is changed.
Fixes: 9aaa3b8b4c56 ("thunderbolt: Add support for preboot ACL")
Reported-and-tested-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Christian Kellner <christian@kellner.me>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the target_core_user use case, after the device is unregistered
it maybe still opened in user space, then the kernel will crash, like:
[ 251.163692] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[ 251.163820] IP: [<ffffffffc0736213>] show_name+0x23/0x40 [uio]
[ 251.163965] PGD 8000000062694067 PUD 62696067 PMD 0
[ 251.164097] Oops: 0000 [#1] SMP
...
[ 251.165605] e1000 mptscsih mptbase drm_panel_orientation_quirks dm_mirror dm_region_hash dm_log dm_mod
[ 251.166014] CPU: 0 PID: 13380 Comm: tcmu-runner Kdump: loaded Not tainted 3.10.0-916.el7.test.x86_64 #1
[ 251.166381] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017
[ 251.166747] task: ffff971eb91db0c0 ti: ffff971e9e384000 task.ti: ffff971e9e384000
[ 251.167137] RIP: 0010:[<ffffffffc0736213>] [<ffffffffc0736213>] show_name+0x23/0x40 [uio]
[ 251.167563] RSP: 0018:ffff971e9e387dc8 EFLAGS: 00010282
[ 251.167978] RAX: 0000000000000000 RBX: ffff971e9e3f8000 RCX: ffff971eb8368d98
[ 251.168408] RDX: ffff971e9e3f8000 RSI: ffffffffc0738084 RDI: ffff971e9e3f8000
[ 251.168856] RBP: ffff971e9e387dd0 R08: ffff971eb8bc0018 R09: 0000000000000000
[ 251.169296] R10: 0000000000001000 R11: ffffffffa09d444d R12: ffffffffa1076e80
[ 251.169750] R13: ffff971e9e387f18 R14: 0000000000000001 R15: ffff971e9cfb1c80
[ 251.170213] FS: 00007ff37d175880(0000) GS:ffff971ebb600000(0000) knlGS:0000000000000000
[ 251.170693] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 251.171248] CR2: 0000000000000008 CR3: 00000000001f6000 CR4: 00000000003607f0
[ 251.172071] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 251.172640] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 251.173236] Call Trace:
[ 251.173789] [<ffffffffa0c9b2d3>] dev_attr_show+0x23/0x60
[ 251.174356] [<ffffffffa0f561b2>] ? mutex_lock+0x12/0x2f
[ 251.174892] [<ffffffffa0ac6d9f>] sysfs_kf_seq_show+0xcf/0x1f0
[ 251.175433] [<ffffffffa0ac54e6>] kernfs_seq_show+0x26/0x30
[ 251.175981] [<ffffffffa0a63be0>] seq_read+0x110/0x3f0
[ 251.176609] [<ffffffffa0ac5d45>] kernfs_fop_read+0xf5/0x160
[ 251.177158] [<ffffffffa0a3d3af>] vfs_read+0x9f/0x170
[ 251.177707] [<ffffffffa0a3e27f>] SyS_read+0x7f/0xf0
[ 251.178268] [<ffffffffa0f648af>] system_call_fastpath+0x1c/0x21
[ 251.178823] Code: 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 53 48 89 d3 e8 7e 96 56 e0 48 8b 80 d8 02 00 00 48 89 df 48 c7 c6 84 80 73 c0 <48> 8b 50 08 31 c0 e8 e2 67 44 e0 5b 48 98 5d c3 0f 1f 00 66 2e
[ 251.180115] RIP [<ffffffffc0736213>] show_name+0x23/0x40 [uio]
[ 251.180820] RSP <ffff971e9e387dc8>
[ 251.181473] CR2: 0000000000000008
CC: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
CC: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We are hitting a regression with the following commit:
commit a93e7b331568227500186a465fee3c2cb5dffd1f
Author: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Date: Mon May 14 13:32:23 2018 +1200
uio: Prevent device destruction while fds are open
The problem is the addition of spin_lock_irqsave in uio_write. This
leads to hitting uio_write -> copy_from_user -> _copy_from_user ->
might_fault and the logs filling up with sleeping warnings.
I also noticed some uio drivers allocate memory, sleep, grab mutexes
from callouts like open() and release and uio is now doing
spin_lock_irqsave while calling them.
Reported-by: Mike Christie <mchristi@redhat.com>
CC: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prepraing for changing to use mutex lock.
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If 'fpga_mgr_create()' fails, we should release some resources, as done
in the other error handling path of the function.
Fixes: 7085e2a94f7d ("fpga: manager: change api, don't use drvdata")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This read handler had a lot of custom logic and wrote outside the bounds of
the provided buffer. This could lead to kernel and userspace memory
corruption. Just use simple_read_from_buffer() with a stack buffer.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is two minor bug fixes (aacraid, target) and a fix for a
potential exploit in the way sg handles teardown"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: mitigate read/write abuse
scsi: aacraid: Fix PD performance regression over incorrect qd being set
scsi: target: Fix truncated PR-in ReadKeys response
|
|
Pull block fixes from Jens Axboe:
"Two minor fixes for this series:
- add LOOP_SET_BLOCK_SIZE as compat ioctl (Evan Green)
- drbd use-after-free fix (Lars Ellenberg)"
* tag 'for-linus-20180706' of git://git.kernel.dk/linux-block:
loop: Add LOOP_SET_BLOCK_SIZE in compat ioctl
drbd: fix access after free
|
