| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The RADXA ROCK 5T board uses the same GPIO pin for controlling the USB
host port regulator. This control pin was mistakenly left out of the
ROCK 5T device tree.
Reported-by: FUKAUMI Naoki <naoki@radxa.com>
Closes: https://libera.catirclogs.org/linux-rockchip/2025-08-25#38609886;
Fixes: 0ea651de9b79 ("arm64: dts: rockchip: add ROCK 5T device tree")
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250825-rock5t-usb-fix-v1-1-de71954a1bb5@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Patches for the arm64 defconfig are supposed to be sent to the
SoC maintainers (e.g. a change in the generic arm64 defconfig
required for Rockchip devices should be send to Heiko Stübner
as he is listed as maintainer for "ARM/Rockchip SoC support")
and not the ARM64 PORT maintainers.
While we cannot easily describe this in MAINTAINERS, we can at
least stop it from giving false information and make it behave
the same way as for the MAINTAINERS file itself (which basically
has the same rules), so that it just outputs the LKML for the
ARM64 defconfig.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20250818-arm64-defconfig-v1-1-f589553c3d72@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Axiado AX3000 EVK has total of 4 UART ports. Add missing alias for uart0,
uart1, uart2.
This fixes the probe failures on the remaining UARTs.
Fixes: 1f7055779001 ("arm64: dts: axiado: Add initial support for AX3000 SoC and eval board")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Harshit Shah <hshah@axiado.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The company's email address has been changed, so update my email
address in MAINTAINERS and .mailmap files.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.x90@mail.toshiba>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As documented in the PinephonePro-Schematic-V1.0-20211127.pdf,
page 11, the SPI Flash's VCC pin is connected to VCC_1V8 power
source. This fixes the following warning:
spi-nor spi1.0: supply vcc not found, using dummy regulator
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Ondřej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20250827143501.1646163-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
|
|
Use the correct es8388 address for rk3588s-roc-ps
Signed-off-by: Kaison Deng <dkx@t-chip.com.cn>
Link: https://lore.kernel.org/r/20250814043230.2774813-1-dkx@t-chip.com.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: 7b4a8097e58b ("arm64: dts: rockchip: Add Neardi LBA3368 board")
Cc: stable+noautosel@kernel.org # Needs testing, because actual level is just a guess
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-By: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20250818090445.28112-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Both network PHYs have dedicated crystals for the 25 MHz clock
and do not source it from the RK3576.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250818-sige5-network-phy-clock-v1-1-87a9122d41c2@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The DTS code coding style expects exactly one space around '=' or '{'
characters.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250819131607.86338-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The DTS code coding style expects exactly one space around '='
character.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250819131607.86338-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The eMMC description is missing both vmmc and vqmmc supplies.
Add them to complete the description.
Fixes: 236d225e1ee7 ("arm64: dts: rockchip: Add board device tree for rk3588-orangepi-5-plus")
Fixes: ea63f4666e48 ("arm64: dts: rockchip: refactor common rk3588-orangepi-5.dtsi")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250821052939.1869171-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The logic of the headphone detect pin seems to be inverted, with this
change headphones actually output sound when plugged in.
Verified by checking /sys/kernel/debug/gpio and by listening.
Fixes: 236d225e1ee7 ("arm64: dts: rockchip: Add board device tree for rk3588-orangepi-5-plus")
Signed-off-by: Maud Spierings <maud_spierings@hotmail.com>
Reviewed-by: Ondřej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20250823-orangepi5-v1-1-ae77dd0e06d7@hotmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Currently the reader of set_ftrace_filter and set_ftrace_notrace just adds
the pointer to the global tracer hash to its iterator. Unlike the writer
that allocates a copy of the hash, the reader keeps the pointer to the
filter hashes. This is problematic because this pointer is static across
function calls that release the locks that can update the global tracer
hashes. This can cause UAF and similar bugs.
Allocate and copy the hash for reading the filter files like it is done
for the writers. This not only fixes UAF bugs, but also makes the code a
bit simpler as it doesn't have to differentiate when to free the
iterator's hash between writers and readers.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/20250822183606.12962cc3@batman.local.home
Fixes: c20489dad156 ("ftrace: Assign iter->hash to filter or notrace hashes on seq read")
Closes: https://lore.kernel.org/all/20250813023044.2121943-1-wutengda@huaweicloud.com/
Closes: https://lore.kernel.org/all/20250822192437.GA458494@ax162/
Reported-by: Tengda Wu <wutengda@huaweicloud.com>
Tested-by: Tengda Wu <wutengda@huaweicloud.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
When calling ftrace_dump_one() concurrently with reading trace_pipe,
a WARN_ON_ONCE() in trace_printk_seq() can be triggered due to a race
condition.
The issue occurs because:
CPU0 (ftrace_dump) CPU1 (reader)
echo z > /proc/sysrq-trigger
!trace_empty(&iter)
trace_iterator_reset(&iter) <- len = size = 0
cat /sys/kernel/tracing/trace_pipe
trace_find_next_entry_inc(&iter)
__find_next_entry
ring_buffer_empty_cpu <- all empty
return NULL
trace_printk_seq(&iter.seq)
WARN_ON_ONCE(s->seq.len >= s->seq.size)
In the context between trace_empty() and trace_find_next_entry_inc()
during ftrace_dump, the ring buffer data was consumed by other readers.
This caused trace_find_next_entry_inc to return NULL, failing to populate
`iter.seq`. At this point, due to the prior trace_iterator_reset, both
`iter.seq.len` and `iter.seq.size` were set to 0. Since they are equal,
the WARN_ON_ONCE condition is triggered.
Move the trace_printk_seq() into the if block that checks to make sure the
return value of trace_find_next_entry_inc() is non-NULL in
ftrace_dump_one(), ensuring the 'iter.seq' is properly populated before
subsequent operations.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Ingo Molnar <mingo@elte.hu>
Link: https://lore.kernel.org/20250822033343.3000289-1-wutengda@huaweicloud.com
Fixes: d769041f8653 ("ring_buffer: implement new locking")
Signed-off-by: Tengda Wu <wutengda@huaweicloud.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The output of the function graph tracer has two ways to display its
entries. One way for leaf functions with no events recorded within them,
and the other is for functions with events recorded inside it. As function
graph has an entry and exit event, to simplify the output of leaf
functions it combines the two, where as non leaf functions are separate:
2) | invoke_rcu_core() {
2) | raise_softirq() {
2) 0.391 us | __raise_softirq_irqoff();
2) 1.191 us | }
2) 2.086 us | }
The __raise_softirq_irqoff() function above is really two events that were
merged into one. Otherwise it would have looked like:
2) | invoke_rcu_core() {
2) | raise_softirq() {
2) | __raise_softirq_irqoff() {
2) 0.391 us | }
2) 1.191 us | }
2) 2.086 us | }
In order to do this merge, the reading of the trace output file needs to
look at the next event before printing. But since the pointer to the event
is on the ring buffer, it needs to save the entry event before it looks at
the next event as the next event goes out of focus as soon as a new event
is read from the ring buffer. After it reads the next event, it will print
the entry event with either the '{' (non leaf) or ';' and timestamps (leaf).
The iterator used to read the trace file has storage for this event. The
problem happens when the function graph tracer has arguments attached to
the entry event as the entry now has a variable length "args" field. This
field only gets set when funcargs option is used. But the args are not
recorded in this temp data and garbage could be printed. The entry field
is copied via:
data->ent = *curr;
Where "curr" is the entry field. But this method only saves the non
variable length fields from the structure.
Add a helper structure to the iterator data that adds the max args size to
the data storage in the iterator. Then simply copy the entire entry into
this storage (with size protection).
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/20250820195522.51d4a268@gandalf.local.home
Reported-by: Sasha Levin <sashal@kernel.org>
Tested-by: Sasha Levin <sashal@kernel.org>
Closes: https://lore.kernel.org/all/aJaxRVKverIjF4a6@lappy/
Fixes: ff5c9c576e75 ("ftrace: Add support for function argument to graph tracer")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad93741 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
|
|
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0aa ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
|
|
The assigned clock for JPEG encoder IP has to be IMX95_CLK_VPUBLK_JPEG_ENC
and not IMX95_CLK_VPUBLK_JPEG_DEC (_ENC at the end, not _DEC). This is a
simple copy-paste error, fix it.
Fixes: 153c039a7357 ("arm64: dts: imx95: add jpeg encode and decode nodes")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
1, the phy support up to 8Mbit/s databitrate for CAN FD.
refer to product data sheet:
https://www.nxp.com/docs/en/data-sheet/TJA1463.pdf
2, the standby pin of the phy is ACTIVE_LOW.
3, the phy of flexcan2 connect the standby/en pin to PCAL6408 on i2c4 bus.
Fixes: 02b7adb791e1 ("arm64: dts: imx95-19x19-evk: add adc0 flexcan[1,2] i2c[2,3] uart5 spi3 and tpm3")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
eDM SBC
Add missing microSD slot vqmmc-supply property, otherwise the kernel
might shut down LDO5 regulator and that would power off the microSD
card slot, possibly while it is in use. Add the property to make sure
the kernel is aware of the LDO5 regulator which supplies the microSD
slot and keeps the LDO5 enabled.
Fixes: 562d222f23f0 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Plus DHCOM
Add missing microSD slot vqmmc-supply property, otherwise the kernel
might shut down LDO5 regulator and that would power off the microSD
card slot, possibly while it is in use. Add the property to make sure
the kernel is aware of the LDO5 regulator which supplies the microSD
slot and keeps the LDO5 enabled.
Fixes: 8d6712695bc8 ("arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
BUCK4 rail supplies the 3.3V rail. Use the actual regulator
instead of a virtual fixed regulator.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix SD card removal caused by automatic LDO5 power off after boot:
LDO5: disabling
mmc1: card 59b4 removed
EXT4-fs (mmcblk1p2): shut down requested (2)
Aborting journal on device mmcblk1p2-8.
JBD2: I/O error when updating journal superblock for mmcblk1p2-8.
To prevent this, add vqmmc regulator for USDHC, using a GPIO-controlled
regulator that is supplied by LDO5. Since this is implemented on SoM but
used on baseboards with SD-card interface, implement the functionality
on SoM part and optionally enable it on baseboards if needed.
Fixes: 418d1d840e42 ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The riscv_iommu_pte_fetch() function returns either NULL for
unmapped/never-mapped iova, or a valid leaf pte pointer that
requires no further validation.
riscv_iommu_iova_to_phys() failed to handle NULL returns.
Prevent null pointer dereference in
riscv_iommu_iova_to_phys(), and remove the pte validation.
Fixes: 488ffbf18171 ("iommu/riscv: Paging domain support")
Cc: Tomasz Jeznach <tjeznach@rivosinc.com>
Signed-off-by: XianLiang Huang <huangxianliang@lanxincomputing.com>
Link: https://lore.kernel.org/r/20250820072248.312-1-huangxianliang@lanxincomputing.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Much like arm-smmu in commit 7d835134d4e1 ("iommu/arm-smmu: Make
instance lookup robust"), virtio-iommu appears to have the same issue
where iommu_device_register() makes the IOMMU instance visible to other
API callers (including itself) straight away, but internally the
instance isn't ready to recognise itself for viommu_probe_device() to
work correctly until after viommu_probe() has returned. This matters a
lot more now that bus_iommu_probe() has the DT/VIOT knowledge to probe
client devices the way that was always intended. Tweak the lookup and
initialisation in much the same way as for arm-smmu, to ensure that what
we register is functional and ready to go.
Cc: stable@vger.kernel.org
Fixes: bcb81ac6ae3c ("iommu: Get DT/ACPI parsing into the proper probe path")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/308911aaa1f5be32a3a709996c7bd6cf71d30f33.1755190036.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
The arm_smmu_attach_commit() updates master->ats_enabled before calling
arm_smmu_remove_master_domain() that is supposed to clean up everything
in the old domain, including the old domain's nr_ats_masters. So, it is
supposed to use the old ats_enabled state of the device, not an updated
state.
This isn't a problem if switching between two domains where:
- old ats_enabled = false; new ats_enabled = false
- old ats_enabled = true; new ats_enabled = true
but can fail cases where:
- old ats_enabled = false; new ats_enabled = true
(old domain should keep the counter but incorrectly decreased it)
- old ats_enabled = true; new ats_enabled = false
(old domain needed to decrease the counter but incorrectly missed it)
Update master->ats_enabled after arm_smmu_remove_master_domain() to fix
this.
Fixes: 7497f4211f4f ("iommu/arm-smmu-v3: Make changing domains be hitless for ATS")
Cc: stable@vger.kernel.org
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Pranjal Shrivastava <praan@google.com>
Link: https://lore.kernel.org/r/20250801030127.2006979-1-nicolinc@nvidia.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Opcode handlers like POLL_ADD will use ->async_data as the pointer for
double poll handling, which is a bit different than the usual case
where it's strictly gated by the REQ_F_ASYNC_DATA flag. Be a bit more
proactive in handling ->async_data, and clear it to NULL as part of
regular init. Init is touching that cacheline anyway, so might as well
clear it.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The io_futex_data is allocated upfront and assigned to the io_kiocb
async_data field, but the request isn't marked with REQ_F_ASYNC_DATA
at that point. Those two should always go together, as the flag tells
io_uring whether the field is valid or not.
Additionally, on failure cleanup, the futex handler frees the data but
does not clear ->async_data. Clear the data and the flag in the error
path as well.
Thanks to Trend Micro Zero Day Initiative and particularly ReDress for
reporting this.
Cc: stable@vger.kernel.org
Fixes: 194bb58c6090 ("io_uring: add support for futex wake and wait")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If the argument check during an array bind fails, the bind_ops are freed
twice as seen below. Fix this by setting bind_ops to NULL after freeing.
==================================================================
BUG: KASAN: double-free in xe_vm_bind_ioctl+0x1b2/0x21f0 [xe]
Free of addr ffff88813bb9b800 by task xe_vm/14198
CPU: 5 UID: 0 PID: 14198 Comm: xe_vm Not tainted 6.16.0-xe-eudebug-cmanszew+ #520 PREEMPT(full)
Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR5 RVP, BIOS ADLPFWI1.R00.2411.A02.2110081023 10/08/2021
Call Trace:
<TASK>
dump_stack_lvl+0x82/0xd0
print_report+0xcb/0x610
? __virt_addr_valid+0x19a/0x300
? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe]
kasan_report_invalid_free+0xc8/0xf0
? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe]
? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe]
check_slab_allocation+0x102/0x130
kfree+0x10d/0x440
? should_fail_ex+0x57/0x2f0
? xe_vm_bind_ioctl+0x1b2/0x21f0 [xe]
xe_vm_bind_ioctl+0x1b2/0x21f0 [xe]
? __pfx_xe_vm_bind_ioctl+0x10/0x10 [xe]
? __lock_acquire+0xab9/0x27f0
? lock_acquire+0x165/0x300
? drm_dev_enter+0x53/0xe0 [drm]
? find_held_lock+0x2b/0x80
? drm_dev_exit+0x30/0x50 [drm]
? drm_ioctl_kernel+0x128/0x1c0 [drm]
drm_ioctl_kernel+0x128/0x1c0 [drm]
? __pfx_xe_vm_bind_ioctl+0x10/0x10 [xe]
? find_held_lock+0x2b/0x80
? __pfx_drm_ioctl_kernel+0x10/0x10 [drm]
? should_fail_ex+0x57/0x2f0
? __pfx_xe_vm_bind_ioctl+0x10/0x10 [xe]
drm_ioctl+0x352/0x620 [drm]
? __pfx_drm_ioctl+0x10/0x10 [drm]
? __pfx_rpm_resume+0x10/0x10
? do_raw_spin_lock+0x11a/0x1b0
? find_held_lock+0x2b/0x80
? __pm_runtime_resume+0x61/0xc0
? rcu_is_watching+0x20/0x50
? trace_irq_enable.constprop.0+0xac/0xe0
xe_drm_ioctl+0x91/0xc0 [xe]
__x64_sys_ioctl+0xb2/0x100
? rcu_is_watching+0x20/0x50
do_syscall_64+0x68/0x2e0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7fa9acb24ded
Fixes: b43e864af0d4 ("drm/xe/uapi: Add DRM_XE_VM_BIND_FLAG_CPU_ADDR_MIRROR")
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Christoph Manszewski <christoph.manszewski@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250813101231.196632-2-christoph.manszewski@intel.com
(cherry picked from commit a01b704527c28a2fd43a17a85f8996b75ec8492a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Currently, ASID assignment for user VMs and page-table BO accounting for
client memory tracking are performed in xe_vm_create_ioctl.
To consolidate VM object initialization, move this logic to
xe_vm_create.
v2:
- removed unnecessary duplicate BO tracking code
- using the local variable xef to verify whether the VM is being created
by userspace
Fixes: 658a1c8e0a66 ("drm/xe: Assign ioctl xe file handler to vm in xe_vm_create")
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://lore.kernel.org/r/20250811104358.2064150-3-piotr.piorkowski@intel.com
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
(cherry picked from commit 30e0c3f43a414616e0b6ca76cf7f7b2cd387e1d4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo: Added fixes tag]
|
|
recent patches to add a WARN() when replacing skb dst entry found an
old bug:
WARNING: include/linux/skbuff.h:1165 skb_dst_check_unset include/linux/skbuff.h:1164 [inline]
WARNING: include/linux/skbuff.h:1165 skb_dst_set include/linux/skbuff.h:1210 [inline]
WARNING: include/linux/skbuff.h:1165 nf_reject_fill_skb_dst+0x2a4/0x330 net/ipv4/netfilter/nf_reject_ipv4.c:234
[..]
Call Trace:
nf_send_unreach+0x17b/0x6e0 net/ipv4/netfilter/nf_reject_ipv4.c:325
nft_reject_inet_eval+0x4bc/0x690 net/netfilter/nft_reject_inet.c:27
expr_call_ops_eval net/netfilter/nf_tables_core.c:237 [inline]
..
This is because blamed commit forgot about loopback packets.
Such packets already have a dst_entry attached, even at PRE_ROUTING stage.
Instead of checking hook just check if the skb already has a route
attached to it.
Fixes: f53b9b0bdc59 ("netfilter: introduce support for reject at prerouting stage")
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20250820123707.10671-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When kernel lockdown is active, debugfs_locked_down() blocks access to
hypfs files that register ioctl callbacks, even if the ioctl interface
is not required for a function. This unnecessarily breaks userspace
tools that only rely on read operations.
Resolve this by registering a minimal set of file operations during
lockdown, avoiding ioctl registration and preserving access for affected
tooling.
Note that this change restores hypfs functionality when lockdown is
active from early boot (e.g. via lockdown=integrity kernel parameter),
but does not apply to scenarios where lockdown is enabled dynamically
while Linux is running.
Tested-by: Mete Durlu <meted@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Fixes: 5496197f9b08 ("debugfs: Restrict debugfs when the kernel is locked down")
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Currently, hypfs registers ioctl callbacks for all debugfs files,
despite only one file requiring them. This leads to unintended exposure
of unused interfaces to user space and can trigger side effects such as
restricted access when kernel lockdown is enabled.
Restrict ioctl registration to only those files that implement ioctl
functionality to avoid interface clutter and unnecessary access
restrictions.
Tested-by: Mete Durlu <meted@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Fixes: 5496197f9b08 ("debugfs: Restrict debugfs when the kernel is locked down")
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
The entry of the validators table for UAC3 feature unit is defined
with a wrong sub-type UAC_FEATURE (= 0x06) while it should have been
UAC3_FEATURE (= 0x07). This patch corrects the entry value.
Fixes: 57f8770620e9 ("ALSA: usb-audio: More validations of descriptor units")
Link: https://patch.msgid.link/20250821150835.8894-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When port buffer headroom changes, port_update_shared_buffer()
recalculates the shared buffer size and splits it in a 3:1 ratio
(lossy:lossless) - Currently, the calculation is:
lossless = shared / 4;
lossy = (shared / 4) * 3;
Meaning, the calculation dropped the remainder of shared % 4 due to
integer division, unintentionally reducing the total shared buffer
by up to three cells on each update. Over time, this could shrink
the buffer below usable size.
Fix it by changing the calculation to:
lossless = shared / 4;
lossy = shared - lossless;
This retains all buffer cells while still approximating the
intended 3:1 split, preventing capacity loss over time.
While at it, perform headroom calculations in units of cells rather than
in bytes for more accurate calculations avoiding extra divisions.
Fixes: a440030d8946 ("net/mlx5e: Update shared buffer along with device buffer changes")
Signed-off-by: Armen Ratner <armeng@nvidia.com>
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20250820133209.389065-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The SW currently saves local buffer ownership when setting
the buffer.
This means that the SW assumes it has ownership of the buffer
after the command is set.
If setting the buffer fails and we remain in FW ownership,
the local buffer ownership state incorrectly remains as SW-owned.
This leads to incorrect behavior in subsequent PFC commands,
causing failures.
Instead of saving local buffer ownership in SW,
query the FW for buffer ownership when setting the buffer.
This ensures that the buffer ownership state is accurately
reflected, avoiding the issues caused by incorrect ownership
states.
Fixes: ecdf2dadee8e ("net/mlx5e: Receive buffer support for DCBX")
Signed-off-by: Alexei Lazar <alazar@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-8-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Restore the __esw_qos_free_node() call removed by the offending commit.
Fixes: 97733d1e00a0 ("net/mlx5: Add traffic class scheduling support for vport QoS")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing esw_qos_put() call when __esw_qos_alloc_node() fails in
mlx5_esw_qos_vport_enable().
Fixes: be034baba83e ("net/mlx5: Make vport QoS enablement more flexible for future extensions")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a VF has been configured and the user later clears all QoS settings,
the vport element remains in the firmware QoS tree. This leads to
inconsistent behavior compared to VFs that were never configured, since
the FW assumes that unconfigured VFs are outside the QoS hierarchy.
As a result, the bandwidth share across VFs may differ, even though
none of them appear to have any configuration.
Align the driver behavior with the FW expectation by destroying the
vport QoS element when all configurations are removed.
Fixes: c9497c98901c ("net/mlx5: Add support for setting VF min rate")
Fixes: cf7e73770d1b ("net/mlx5: Manage TC arbiter nodes and implement full support for tc-bw")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20250820133209.389065-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When changing parent of a node/leaf with tc-bw configured, the code
saves and restores tc-bw values. However, it was reading the converted
hardware bw_share values (where 0 becomes 1) instead of the original
user values, causing incorrect tc-bw calculations after parent change.
Store original tc-bw values in the node structure and use them directly
for save/restore operations.
Fixes: cf7e73770d1b ("net/mlx5: Manage TC arbiter nodes and implement full support for tc-bw")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the driver creates a default group (`node0`) and attaches
all vports to it unless the user explicitly sets a parent group. As a
result, when a user configures tx_share on a group and tx_share on
a VF, the expectation is for the group and the VF to share bandwidth
relatively. However, since the VF is not connected to the same parent
(but to the default node), the proportional share logic is not applied
correctly.
To fix this, remove the default group (`node0`) and instead connect
vports directly to the root TSAR when no parent is specified. This
ensures that vports and groups share the same root scheduler and their
tx_share values are compared directly under the same hierarchy.
Fixes: 0fe132eac38c ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adjust the vport number by the base ECVF vport number so the port
attributes start at 0. Previously the port attributes would start 1
after the maximum number of host VFs.
Fixes: dc13180824b7 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250820133209.389065-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the power supply's power budget is not defined in the device tree,
the current code still requests power and configures the PSE manager
with a 0W power limit, which is undesirable behavior.
Skip power budget configuration entirely when the budget is zero,
avoiding unnecessary power requests and preventing invalid 0W limits
from being set on the PSE manager.
Fixes: 359754013e6a ("net: pse-pd: pd692x0: Add support for PSE PI priority feature")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250820133321.841054-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a resource leak where manager power budgets were freed on both
success and error paths during manager setup. Power budgets should
only be freed on error paths after regulator registration or during
driver removal.
Refactor cleanup logic by extracting OF node cleanup and power budget
freeing into separate helper functions for better maintainability.
Fixes: 359754013e6a ("net: pse-pd: pd692x0: Add support for PSE PI priority feature")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250820132708.837255-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Octeontx2/CN10K silicon supports generating a 256-bit key per packet.
The specific fields to be extracted from a packet for key generation
are configurable via a Key Extraction (MKEX) Profile.
The AF driver scans the configured extraction profile to ensure that
fields from upper layers do not overwrite fields from lower layers in
the key.
Example Packet Field Layout:
LA: DMAC + SMAC
LB: VLAN
LC: IPv4/IPv6
LD: TCP/UDP
Valid MKEX Profile Configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[30-31]
Invalid MKEX profile configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[2-3] // Overlaps with DMAC field
In another scenario, if the MKEX profile is configured to extract
the SPI field from both AH and ESP headers at the same key offset,
the driver rejecting this configuration. In a regular traffic,
ipsec packet will be having either AH(LD) or ESP (LE). This patch
relaxes the check for the same.
Fixes: 12aa0a3b93f3 ("octeontx2-af: Harden rule validation.")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250820063919.1463518-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Test various combinations of zero-length records.
Unfortunately, kernel cannot be coerced into producing those,
so hardcode the ciphertext messages in the test.
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20250820021952.143068-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Each recvmsg() call must process either
- only contiguous DATA records (any number of them)
- one non-DATA record
If the next record has different type than what has already been
processed we break out of the main processing loop. If the record
has already been decrypted (which may be the case for TLS 1.3 where
we don't know type until decryption) we queue the pending record
to the rx_list. Next recvmsg() will pick it up from there.
Queuing the skb to rx_list after zero-copy decrypt is not possible,
since in that case we decrypted directly to the user space buffer,
and we don't have an skb to queue (darg.skb points to the ciphertext
skb for access to metadata like length).
Only data records are allowed zero-copy, and we break the processing
loop after each non-data record. So we should never zero-copy and
then find out that the record type has changed. The corner case
we missed is when the initial record comes from rx_list, and it's
zero length.
Reported-by: Muhammad Alifa Ramdhan <ramdhan@starlabs.sg>
Reported-by: Billy Jheng Bing-Jhong <billy@starlabs.sg>
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser")
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20250820021952.143068-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A recent lockdep[1] splat observed while running blktest block/005
reveals a potential deadlock caused by the cpu_hotplug_lock dependency
on ->freeze_lock. This dependency was introduced by commit 033b667a823e
("block: blk-rq-qos: guard rq-qos helpers by static key").
That change added a static key to avoid fetching q->rq_qos when
neither blk-wbt nor blk-iolatency is configured. The static key
dynamically patches kernel text to a NOP when disabled, eliminating
overhead of fetching q->rq_qos in the I/O hot path. However, enabling
a static key at runtime requires acquiring both cpu_hotplug_lock and
jump_label_mutex. When this happens after the queue has already been
frozen (i.e., while holding ->freeze_lock), it creates a locking
dependency from cpu_hotplug_lock to ->freeze_lock, which leads to a
potential deadlock reported by lockdep [1].
To resolve this, replace the static key mechanism with q->queue_flags:
QUEUE_FLAG_QOS_ENABLED. This flag is evaluated in the fast path before
accessing q->rq_qos. If the flag is set, we proceed to fetch q->rq_qos;
otherwise, the access is skipped.
Since q->queue_flags is commonly accessed in IO hotpath and resides in
the first cacheline of struct request_queue, checking it imposes minimal
overhead while eliminating the deadlock risk.
This change avoids the lockdep splat without introducing performance
regressions.
[1] https://lore.kernel.org/linux-block/4fdm37so3o4xricdgfosgmohn63aa7wj3ua4e5vpihoamwg3ui@fq42f5q5t5ic/
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Closes: https://lore.kernel.org/linux-block/4fdm37so3o4xricdgfosgmohn63aa7wj3ua4e5vpihoamwg3ui@fq42f5q5t5ic/
Fixes: 033b667a823e ("block: blk-rq-qos: guard rq-qos helpers by static key")
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250814082612.500845-4-nilay@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
rq_qos_add() increments the block_rq_qos static key when a QoS
policy is attached. When a QoS policy is removed via rq_qos_del(),
we must symmetrically decrement the static key. If this removal drops
the last QoS policy from the queue (q->rq_qos becomes NULL), the
static branch can be disabled and the jump label patched to a NOP,
avoiding overhead on the hot path.
This change ensures rq_qos_add()/rq_qos_del() keep the
block_rq_qos static key balanced and prevents leaving the branch
permanently enabled after the last policy is removed.
Fixes: 033b667a823e ("block: blk-rq-qos: guard rq-qos helpers by static key")
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250814082612.500845-3-nilay@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
