| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It's legal for drivers to provide the QP port through the
QPC schedule-queue field on the reset-to-init QP state change.
Add adjusting of the schedule queue port in the SRIOV wrapper
for that operation too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some VF drivers flow set the schedule queue in the QP context but
without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH.
To allow for such non-modified drivers to function as single ported
IB VFs, we must adjust the schedule queue port whenever being set,
e.g as currently done for single ported Eth VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.
This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.
(1) make sure that events are generated only for VFs sitting on
the relevant physical port (under the ALL_SLAVES flow).
(2) before generating the event, convert from physical (one or two)
to VF port (always equals one).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When multiplexling a MAD sent from VF, we should convert the port used
by the guest to send the packet to the actual physical port which will be
used to transmit the packet, before building the relevant address-handle (AH).
This is needed under VPI for single ported VFs, since the code that builds
the AH (mlx4_ib_query_ah()) makes decisions based on the input port. If we
use the port number provided by the guest, it might have different protocol
vs. the one this packat has to go from, and hence the result could be wrong.
So far, the conversion was done after the AH was built and it worked for
single ported Eth VFs which were not enabled under VPI. When adding support
for single ported IB VFs and VPI, we hit that.
Fixes: 449fc48866f7 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Single port VFs always provide port = 1 (even if the actual physical
port used is port 2). As such, we need to convert the port provided
by the VF to the physical port before calling into the firmware.
It turns out that the Linux mlx4 VF RoCE driver maintains a copy of
the GID table and hence this change became critical only for single
ported IB VFs, but it could be needed for other RoCE VF drivers too.
Fixes: 449fc48866f7 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
