| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
They are pointless. As dtc points out:
Warning (avoid_unnecessary_addr_size):
/mipi@ff960000:
unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Let's remove them.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The device tree compiler yells like this:
Warning (unit_address_vs_reg):
/gpu-opp-table/opp@100000000:
node has a unit name, but no reg property
Let's match the cpu opp node names and use a dash.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Various rk3328 based boards experience occasional sdmmc0 write errors.
This is due to the rk3328.dtsi tx drive levels being set to 4ma, vs
8ma per the rk3328 datasheet default settings.
Fix this by setting the tx signal pins to 8ma.
Inspiration from tonymac32's patch,
https://github.com/ayufan-rock64/linux-kernel/commit/dc1212b347e0da17c5460bcc0a56b07d02bac3f8
Fixes issues on the rk3328-roc-cc and the rk3328-rock64 (as per the
above commit message).
Tested on the rk3328-roc-cc board.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Several rk3328 based boards experience high rgmii tx error rates.
This is due to several pins in the rk3328.dtsi rgmii pinmux that are
missing a defined pull strength setting.
This causes the pinmux driver to default to 2ma (bit mask 00).
These pins are only defined in the rk3328.dtsi, and are not listed in
the rk3328 specification.
The TRM only lists them as "Reserved"
(RK3328 TRM V1.1, 3.3.3 Detail Register Description, GRF_GPIO0B_IOMUX,
GRF_GPIO0C_IOMUX, GRF_GPIO0D_IOMUX).
However, removal of these pins from the rgmii pinmux definition causes
the interface to fail to transmit.
Also, the rgmii tx and rx pins defined in the dtsi are not consistent
with the rk3328 specification, with tx pins currently set to 12ma and
rx pins set to 2ma.
Fix this by setting tx pins to 8ma and the rx pins to 4ma, consistent
with the specification.
Defining the drive strength for the undefined pins eliminated the high
tx packet error rate observed under heavy data transfers.
Aligning the drive strength to the TRM values eliminated the occasional
packet retry errors under iperf3 testing.
This allows much higher data rates with no recorded tx errors.
Tested on the rk3328-roc-cc board.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Problem:
On ASUS Tinker Board S, when booting from the eMMC, and there is card
in the sd slot, there are constant errors.
Also when warm reboot, uboot can not access the sd slot
Cause:
Identified by Robin Murphy @ ARM. The Card Detect on rk3288
devices is pulled up by vccio-sd; so when the regulator powers this
off, card detect gives spurious errors. A second problem, is during
power down, vccio-sd apprears to be powered down. This causes a
problem when warm rebooting from the sd card. This was identified by
Jonas Karlman.
History:
A common fault on these rk3288 board, which impliment the reference
design.
When this arose before:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-August/281153.html
And Ulf and Jaehoon clearly said this was a broken card detect design,
which should be solved via polling
Solution:
Hence broken-cd is set as a property. This cures the errors. The
powering down of vccio-sd during reboot is cured by adding
regulator-boot-on.
This solutions has been fairly widely reviewed and tested.
Fixes: e58c5e739d6f ("ARM: dts: rockchip: move shared tinker-board nodes to a common dtsi")
Cc: stable@vger.kernel.org
[Heiko: slightly inaccurate fixes but tinker is a sbc (aka like a Pi) where
we can hopefully expect people not to rely on overly old stable kernels]
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch makes USB ports functioning again.
Fixes: 955bebde057e ("arm64: dts: rockchip: add rk3328-rock64 board")
Cc: stable@vger.kernel.org
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Tomohiro Mayama <parly-gh@iris.mystia.org>
Tested-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The following error can be seen during boot:
of: /cpus/cpu@501: Couldn't find opp node
Change cpu nodes to use operating-points-v2 in order to fix this.
Fixes: ce76de984649 ("ARM: dts: rockchip: convert rk3288 to operating-points-v2")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A DDC I2C bus specifier is required for DDC EDID probing to work
properly.
Fixes: 1b5715c602fda ("arm64: dts: rockchip: add ROCK Pi 4 DTS support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The rk3328-roc-cc board exhibits tx stability issues with large packets,
as does the rock64 board, which was fixed with this patch
https://patchwork.kernel.org/patch/10178969/
A similar patch was merged for the rk3328-roc-cc here
https://patchwork.kernel.org/patch/10804863/
but it doesn't include the tx/rx_delay tweaks, and I find that they
help with an issue where large transfers would bring the ethernet
link down, causing a link reset regularly.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
|
|
Fixes: 400816f60c54 ("perf/x86/intel: Implement support for TSX Force Abort")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: kbuild-all@01.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190313184243.GA10820@lkp-sb-ep06
|
|
When this .gitignore was added, lxdialog was an independent hostprogs-y.
Now that all objects in lxdialog/ are directly linked to mconf, the
lxdialog is no longer generated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The generic-y is redundant under the following condition:
- arch has its own implementation
- the same header is added to generated-y
- the same header is added to mandatory-y
If a redundant generic-y is found, the warning like follows is displayed:
scripts/Makefile.asm-generic:20: redundant generic-y found in arch/arm/include/asm/Kbuild: timex.h
I fixed up arch Kbuild files found by this.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit caf6fe91ddf62a96401e21e9b7a07227440f4185.
The commit was fine but is no longer needed as of commit 3a2429e1faf4
("kbuild: change if_changed_rule for multi-line recipe"). Let's go
back to using ";" to be consistent.
For some discussion, see:
https://lkml.kernel.org/r/CAK7LNASde0Q9S5GKeQiWhArfER4S4wL1=R_FW8q0++_X3T5=hQ@mail.gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
During a simple no-op (nothing changed) build I saw 39 invocations of
the C compiler with the argument "-print-file-name=include". We don't
need to call the C compiler 39 times for this--one time will suffice.
Let's change NOSTDINC_FLAGS to a simply expanded variable to avoid
this since there doesn't appear to be any reason it should be
recursively expanded.
On my build this shaved ~400 ms off my "no-op" build.
Note that the recursive expansion seems to date back to the (really
old) commit e8f5bdb02ce0 ("[PATCH] Makefile include path ordering").
It's a little unclear to me if the point of that patch was to switch
the variable to be recursively expanded (which it did) or to avoid
directly assigning to NOSTDINC_FLAGS (AKA to switch to +=) because
someone else (out of tree?) was setting it. I presume later since if
the only goal was to switch to recursive expansion the patch would
have just removed the ":".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
* The man page for dpkg-source(1) notes:
> -b, --build directory [format-specific-parameters]
> Build a source package (--build since dpkg 1.17.14).
> <...>
>
> dpkg-source will build the source package with the first
> format found in this ordered list: the format indicated
> with the --format command line option, the format
> indicated in debian/source/format, “1.0”. The fallback
> to “1.0” is deprecated and will be removed at some point
> in the future, you should always document the desired
> source format in debian/source/format. See section
> SOURCE PACKAGE FORMATS for an extensive description of
> the various source package formats.
Thus it would be more foolproof to explicitly use 1.0 (as we always
did) than to rely on dpkg-source's defaults.
* In a similar vein, debian/rules is not made executable by mkdebian,
and dpkg-source warns about that but still silently fixes the file.
Let's be explicit once again.
Signed-off-by: Arseny Maslennikov <ar@cs.msu.ru>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
