| Age | Commit message (Collapse) | Author | Lines |
|---|
|
Reference the common PHY properties, and update the example to use them.
Note that a PCS subnode exists, and it seems a better container of the
polarity description than the SGMIISYS node that hosts "mediatek,pnswap".
So use that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260119091220.1493761-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the renesas,miic-phy-link-active-low property to allow configuring
the active level of phy_link status signals provided by the MIIC block.
EtherPHY link-up and link-down status is required as a hardware IP
feature independent of whether GMAC or ETHSW is used. With GMAC, link
state is retrieved via MDC/MDIO and handled in software. In contrast,
ETHSW exposes dedicated PHY_LINK pins that provide this information
directly in hardware.
These PHY_LINK signals are required not only for host-controlled traffic
but also for switch-only forwarding paths where frames are exchanged
between external nodes without CPU involvement. This is particularly
important for redundancy protocols such as DLR (Device Level Ring),
which depend on fast detection of link-down events caused by cable or
port failures. Handling such events purely in software introduces
latency, which is why ETHSW provides dedicated hardware PHY_LINK pins.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260112173555.1166714-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add device tree binding support for RZ/T2H and RZ/N2H SoCs to the
existing RZ/N1 MIIC converter binding. These SoCs share similar MIIC
functionality but have architectural differences that require schema
updates.
Add new compatible strings "renesas,r9a09g077-miic" for RZ/T2H and
"renesas,r9a09g087-miic" for RZ/N2H, with the latter falling back to
the RZ/T2H variant. The new SoCs require reset support with two reset
lines for converter register reset and converter reset, which are not
present on RZ/N1.
Update port configurations to accommodate the different architectures.
RZ/N1 supports 5 ports numbered 1-5 with complex input mappings
covering indices 0-13, while RZ/T2H and RZ/N2H support 4 ports
numbered 0-3 with simplified input mappings covering indices 0-8.
Extend the switch port configuration property to support value 0 for
the new SoCs.
Add a new dt-bindings header file with media interface connection
matrix constants that map GMAC, ESC, and ETHSW ports to numeric
identifiers for use with RZ/T2H and RZ/N2H device trees.
Update DT schema validation to ensure proper port numbering and input
mappings per SoC variant.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250910204132.319975-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Synopsys DesignWare XPCS IP-core is a Physical Coding Sublayer (PCS) layer
providing an interface between the Media Access Control (MAC) and Physical
Medium Attachment Sublayer (PMA) through a Media independent interface.
From software point of view it exposes IEEE std. Clause 45 CSR space and
can be accessible either by MDIO or MCI/APB3 bus interfaces. In the former
case the PCS device is supposed to be defined under the respective MDIO
bus DT-node. In the later case the DW xPCS will be just a normal IO
memory-mapped device.
Besides of that DW XPCS DT-nodes can have an interrupt signal and clock
source properties specified. The former one indicates the Clause 73/37
auto-negotiation events like: negotiation page received, AN is completed
or incompatible link partner. The clock DT-properties can describe up to
three clock sources: peripheral bus clock source, internal reference clock
and the externally connected reference clock.
Finally the DW XPCS IP-core can be optionally synthesized with a
vendor-specific interface connected to the Synopsys PMA (also called
DesignWare Consumer/Enterprise PHY). Alas that isn't auto-detectable in a
portable way. So if the DW XPCS device has the respective PMA attached
then it should be reflected in the DT-node compatible string so the driver
would be aware of the PMA-specific device capabilities (mainly connected
with CSRs available for the fine-tunings).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add various clock controllers found in the MT7988 SoC to existing
bindings (if applicable) and add files for the new ethwarp, mcusys
and xfi-pll clock controllers not previously present in any SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/07e76a544ce4392bcb88e34d5480e99bb7994618.1702849494.git.daniel@makrotopia.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add mediatek,pnswap boolean property needed on many boards using the
MediaTek MT7981 SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert mediatek,sgmiiisys bindings to DT schema format.
Add maintainer Matthias Brugger, no maintainers were listed in the
original documentation.
As this node is also referenced by the Ethernet controller and used
as SGMII PCS add this fact to the description.
Move the file to Documentation/devicetree/bindings/net/pcs/ which seems
more appropriate given that the great majority of registers are related
to SGMII PCS functionality and only one register represents clock bits.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This binding is fairly bare-bones for now, since the Lynx driver doesn't
parse any properties (or match based on the compatible). We just need it
in order to prevent the PCS nodes from having phy devices attached to
them. This is not really a problem, but it is a bit inefficient.
This binding is really for three separate PCSs (SGMII, QSGMII, and XFI).
However, the driver treats all of them the same. This works because the
SGMII and XFI devices typically use the same address, and the SerDes
driver (or RCW) muxes between them. The QSGMII PCSs have the same
register layout as the SGMII PCSs. To do things properly, we'd probably
do something like
ethernet-pcs@0 {
#pcs-cells = <1>;
compatible = "fsl,lynx-pcs";
reg = <0>, <1>, <2>, <3>;
};
but that would add complexity, and we can describe the hardware just
fine using separate PCSs for now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This MII converter can be found on the RZ/N1 processor family. The MII
converter ports are declared as subnodes which are then referenced by
users of the PCS driver such as the switch.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220624144001.95518-5-clement.leger@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
