| Age | Commit message (Collapse) | Author | Lines |
|---|
|
This adds an MDIO driver for PIC64-HPSC/HX. The hardware supports C22
and C45 but only C22 is implemented in this commit.
This MDIO hardware is based on a Microsemi design supported in Linux by
mdio-mscc-miim.c. However, The register interface is completely
different with pic64hpsc, hence the need for a separate driver.
The documentation recommends an input clock of 156.25MHz and a prescaler
of 39, which yields an MDIO clock of 1.95MHz.
The hardware supports an interrupt pin or a "TRIGGER" bit that can be
polled to signal transaction completion. This commit uses polling.
This was tested on Microchip HB1301 evalkit with a VSC8574 and a
VSC8541.
Signed-off-by: Charles Perry <charles.perry@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260408131821.1145334-3-charles.perry@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.0-rc8).
Conflicts:
net/ipv6/seg6_iptunnel.c
c3812651b522f ("seg6: separate dst_cache for input and output paths in seg6 lwtunnel")
78723a62b969a ("seg6: add per-route tunnel source address")
https://lore.kernel.org/adZhwtOYfo-0ImSa@sirena.org.uk
net/ipv4/icmp.c
fde29fd934932 ("ipv4: icmp: fix null-ptr-deref in icmp_build_probe()")
d98adfbdd5c01 ("ipv4: drop ipv6_stub usage and use direct function calls")
https://lore.kernel.org/adO3dccqnr6j-BL9@sirena.org.uk
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/chain_mode.c
51f4e090b9f8 ("net: stmmac: fix integer underflow in chain mode")
6b4286e05508 ("net: stmmac: rename STMMAC_GET_ENTRY() -> STMMAC_NEXT_ENTRY()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Switch to device_for_each_child_node_scoped() to auto-release fwnode
references on early exit.
Fixes: 24e31e474769 ("net: mdio: Add RTL9300 MDIO driver")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260405-rtl9300-v1-1-08e4499cf944@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nobody defines struct mdio_gpio_platform_data. Remove platform data
support from mdio-gpio and drop the header.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260316-gpio-mdio-hdr-cleanup-v1-2-2df696f74728@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The three defines from the linux/mdio-gpio.h header are only used in the
mdio-gpio module. There's no reason to have them in a public header.
Move them into the driver and remove mdio-gpio.h.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260316-gpio-mdio-hdr-cleanup-v1-1-2df696f74728@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fwnode MDIO has never used the fixed PHY code, therefore don't select
symbol FIXED_PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/880ca62b-a5d3-4865-bbce-2d2210928239@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260309082641.15574-1-johan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xgene_xfi_mdio_read() prints "write failed" when the MDIO management
interface remains busy and the read times out. Update the message to
"read failed" to match the operation.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260304195755.2468204-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently in the return path, fwnode_handle_put calls are missing. Just use
_scoped to avoid the issue.
Fixes: 24e31e474769 ("net: mdio: Add RTL9300 MDIO driver")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20251217210153.14641-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Aspeed MDIO controller may return incorrect data when a read operation
follows immediately after a write. Due to a controller bug, the subsequent
read can latch stale data, causing the polling logic to terminate earlier
than expected.
To work around this hardware issue, insert a dummy read after each write
operation. This ensures that the next actual read returns the correct
data and prevents premature polling exit.
This workaround has been verified to stabilize MDIO transactions on
affected Aspeed platforms.
Fixes: f160e99462c6 ("net: phy: Add mdio-aspeed")
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251211-aspeed_mdio_add_dummy_read-v3-1-382868869004@aspeedtech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove redundant fwnode cleanup in of_mdiobus_register_device()
and xpcs_plat_init_dev().
mdio_device_free() eventually calls mdio_device_release(),
which already performs fwnode_handle_put(), making the manual
cleanup unnecessary.
Combine fwnode_handle_get() with device_set_node() in
of_mdiobus_register_device() for clarity.
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/00847693daa8f7c8ff5dfa19dd35fc712fa4e2b5.1763995734.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unify the handling of the per device reset properties for
`mdio_device`.
Merge mdio_device_register_gpiod() and mdio_device_register_reset()
into mdio_device_register_reset(), that handles both
reset-controllers and reset-gpios.
Move reading of the reset firmware properties (reset-assert-us,
reset-deassert-us) from fwnode_mdio.c to mdio_device_register_reset(),
so all reset related initialization code is kept in one place.
Introduce mdio_device_unregister_reset() to release the associated
resources.
These changes make tracking the reset properties easier.
Added kernel-doc for mdio_device_register/unregister_reset().
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Link: https://patch.msgid.link/17c216efd7a47be17db104378b6aacfc8741d8b9.1763473655.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The call to device_node_to_regmap() in airoha_mdio_probe() can return
an ERR_PTR() if regmap initialization fails. Currently, the driver
stores the pointer without validation, which could lead to a crash
if it is later dereferenced.
Add an IS_ERR() check and return the corresponding error code to make
the probe path more robust.
Fixes: 67e3ba978361 ("net: mdio: Add MDIO bus controller for Airoha AN7583")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251031161607.58581-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When accessing an MDIO register using single-byte smbus accesses, we have to
perform 2 consecutive operations targeting the same address,
first accessing the MSB then the LSB of the 16 bit register:
read_1_byte(addr); <- returns MSB of register at address 'addr'
read_1_byte(addr); <- returns LSB
Some PHY devices present in SFP such as the Broadcom 5461 don't like
seeing foreign i2c transactions in-between these 2 smbus accesses, and
will return the MSB a second time when trying to read the LSB :
read_1_byte(addr); <- returns MSB
i2c_transaction_for_other_device_on_the_bus();
read_1_byte(addr); <- returns MSB again
Given the already fragile nature of accessing PHYs/SFPs with single-byte
smbus accesses, it's safe to say that this Broadcom PHY may not be the
only one acting like this.
Let's therefore hold the i2c bus lock while performing our smbus
transactions to avoid interleaved accesses.
Fixes: d4bd3aca33c2 ("net: mdio: mdio-i2c: Add support for single-byte SMBus operations")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251003070311.861135-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Config symbol MDIO_BUS isn't used in drivers/net/mdio. It's only used
in drivers/net/phy. So move it there.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/164ff1c6-2cf9-4e30-80fb-da4cc7165dc8@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The array-style fixed-link binding has been marked deprecated for more
than 10 yrs, but still there's a number of users. Print a warning when
usage of the deprecated binding is detected.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/faf94844-96eb-400f-8a3a-b2a0e93b27d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fixed_phy_register() creates and registers the phy_device. To be
symmetric, we should not only unregister, but also free the phy_device
in fixed_phy_unregister(). This allows to simplify code in users.
Note wrt of_phy_deregister_fixed_link():
put_device(&phydev->mdio.dev) and phy_device_free(phydev) are identical.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/ad8dda9a-10ed-4060-916b-3f13bdbb899d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In light of a81649a4efd3 ("net: mdio: mdio-bcm-unimac: Correct rate
fallback logic"), it became clear that the warning should be specific to
the MDIO controller instance, and there should be further information
provided to indicate what is wrong, whether the requested clock
frequency or the rate calculation. Clarify the message accordingly.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250811165921.392030-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the parent clock is a gated clock which has multiple parents, the
clock provider (clk-scmi typically) might return a rate of 0 since there
is not one of those particular parent clocks that should be chosen for
returning a rate. Prior to ee975351cf0c ("net: mdio: mdio-bcm-unimac:
Manage clock around I/O accesses"), we would not always be passing a
clock reference depending upon how mdio-bcm-unimac was instantiated. In
that case, we would take the fallback path where the rate is hard coded
to 250MHz.
Make sure that we still fallback to using a fixed rate for the divider
calculation, otherwise we simply ignore the desired MDIO bus clock
frequency which can prevent us from interfacing with Ethernet PHYs
properly.
Fixes: ee975351cf0c ("net: mdio: mdio-bcm-unimac: Manage clock around I/O accesses")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250730202533.3463529-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Airoha AN7583 SoC have 2 dedicated MDIO bus controller in the SCU
register map. To driver register an MDIO controller based on the DT
reg property and access the register by accessing the parent syscon.
The MDIO bus logic is similar to the MT7530 internal MDIO bus but
deviates of some setting and some HW bug.
On Airoha AN7583 the MDIO clock is set to 25MHz by default and needs to
be correctly setup to 2.5MHz to correctly work (by setting the divisor
to 10x).
There seems to be Hardware bug where AN7583_MII_RWDATA
is not wiped in the context of unconnected PHY and the
previous read value is returned.
Example: (only one PHY on the BUS at 0x1f)
- read at 0x1f report at 0x2 0x7500
- read at 0x0 report 0x7500 on every address
To workaround this, we reset the Mdio BUS at every read
to have consistent values on read operation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for reporting PSE events via ethtool notifications,
introduce an attached_phydev field in the pse_control structure.
This field stores the phy_device associated with the PSE PI,
ensuring that notifications are sent to the correct network
interface.
The attached_phydev pointer is directly tied to the PHY lifecycle. It
is set when the PHY is registered and cleared when the PHY is removed.
There is no need to use a refcount, as doing so could interfere with
the PHY removal process.
Signed-off-by: Kory Maincent (Dent Project) <kory.maincent@bootlin.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250617-feature_poe_port_prio-v14-1-78a1a645e2ee@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reduce verbosity by using gpiod_multi_set_value_cansleep() instead of
gpiod_set_array_value_cansleep().
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250611-net-mdio-mux-gpio-use-gpiod_multi_set_value_cansleep-v1-1-6eb5281f1b41@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All callers pass PHY_POLL, therefore remove irq argument from
fixed_phy_register().
Note: I keep the irq argument in fixed_phy_add_gpiod() for now,
for the case that somebody may want to use a GPIO interrupt in
the future, by e.g. adding a call to fwnode_irq_get() to
fixed_phy_get_gpiod().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/31cdb232-a5e9-4997-a285-cb9a7d208124@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After having factored out the provider part from mdio_bus.c, we can
make the mdio consumer / device layer a separate module. This also
allows to remove Kconfig symbol MDIO_DEVICE.
The module init / exit functions from mdio_bus.c no longer have to be
called from phy_device.c. The link order defined in
drivers/net/phy/Makefile ensures that init / exit functions are called
in the right order.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dba6b156-5748-44ce-b5e2-e8dc2fcee5a7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
MDIO_DEVRES is only set where PHYLIB/PHYLINK are set which
select MDIO_DEVRES. So we can remove this symbol.
Note: Due to circular module dependencies we can't simply
make mdio_devres.c part of phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/27cba535-f507-4b32-84a3-0744c783a465@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After 52358dd63e34 ("net: phy: remove function stubs") there's a
problem if CONFIG_MDIO_BUS is set, but CONFIG_PHYLIB is not.
mdiobus_scan() uses phylib functions like get_phy_device().
Bringing back the stub wouldn't make much sense, because it would
allow to compile mdiobus_scan(), but the function would be unusable.
The stub returned NULL, and we have the following in mdiobus_scan():
phydev = get_phy_device(bus, addr, c45);
if (IS_ERR(phydev))
return phydev;
So calling mdiobus_scan() w/o CONFIG_PHYLIB would cause a crash later in
mdiobus_scan(). In general the PHYLIB functionality isn't optional here.
Consequently, MDIO bus providers depend on PHYLIB.
Therefore factor it out and build it together with the libphy core
modules. In addition make all MDIO bus providers under /drivers/net/mdio
depend on PHYLIB. Same applies to enetc MDIO bus provider. Note that
PHYLIB selects MDIO_DEVRES, therefore we can omit this here.
Fixes: 52358dd63e34 ("net: phy: remove function stubs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504270639.mT0lh2o1-lkp@intel.com/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c74772a9-dab6-44bf-a657-389df89d85c2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc5).
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This bit is necessary to receive packets from the internal PHY.
Without this bit set, no activity occurs on the interface.
Normally u-boot sets this bit, but if u-boot is compiled without
net support, the interface will be up but without any activity.
If bit is set once, it will work until the IP is powered down or reset.
The vendor SDK sets this bit along with the PHY_ID bits.
Signed-off-by: Da Xue <da@libre.computer>
Fixes: 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://patch.msgid.link/20250425192009.1439508-1-da@libre.computer
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The currently used function pci_request_regions() is one of the
problematic "hybrid devres" PCI functions, which are sometimes managed
through devres, and sometimes not (depending on whether
pci_enable_device() or pcim_enable_device() has been called before).
The PCI subsystem wants to remove this behavior and, therefore, needs to
port all users to functions that don't have this problem.
Furthermore, the PCI function being managed implies that it's not
necessary to call pci_release_regions() manually.
Remove the calls to pci_release_regions().
Replace pci_request_regions() with pcim_request_all_regions().
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250425085740.65304-8-phasta@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The newly added rtl9300 driver needs MDIO_DEVRES:
x86_64-linux-ld: drivers/net/mdio/mdio-realtek-rtl9300.o: in function `rtl9300_mdiobus_probe':
mdio-realtek-rtl9300.c:(.text+0x941): undefined reference to `devm_mdiobus_alloc_size'
x86_64-linux-ld: mdio-realtek-rtl9300.c:(.text+0x9e2): undefined reference to `__devm_mdiobus_register'
Since this is a hidden symbol, it needs to be selected by each user,
rather than the usual 'depends on'. I see that there are a few other
drivers that accidentally use 'depends on', so fix these as well for
consistency and to avoid dependency loops.
Fixes: 37f9b2a6c086 ("net: ethernet: Add missing depends on MDIO_DEVRES")
Fixes: 24e31e474769 ("net: mdio: Add RTL9300 MDIO driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://patch.msgid.link/20250425112819.1645342-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add mdio compat string for asp-v3.0 ethernet driver.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250422233645.1931036-9-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove asp-v2.0 which will no longer be supported.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250422233645.1931036-5-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All callers of these functions depend on PHYLIB or select it directly
or indirectly by selecting PHYLINK. Stubs make sense for optional
functionality, but that's not the case here.
MDIO_XGENE usually is selected by NET_XGENE which also selects PHYLIB.
Add a dependency to PHYLIB nevertheless, in order not to break
randconfig builds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/f7a69a1f-60e9-4ac0-8b7c-481e0cc850e7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a driver for the MDIO controller on the RTL9300 family of Ethernet
switches with integrated SoC. There are 4 physical SMI interfaces on the
RTL9300 however access is done using the switch ports. The driver takes
the MDIO bus hierarchy from the DTS and uses this to configure the
switch ports so they are associated with the correct PHY. This mapping
is also used when dealing with software requests from phylib.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250409231554.3943115-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PHYs that are within copper SFP modules have their MDIO bus accessible
through address 0x56 (usually) on the i2c bus. The MDIO-I2C bridge is
desgned for 16 bits accesses, but we can also perform 8bits accesses by
reading/writing the high and low bytes sequentially.
This commit adds support for this type of accesses, thus supporting
smbus controllers such as the one in the VSC8552.
This was only tested on Copper SFP modules that embed a Marvell 88e1111
PHY.
Tested-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322075745.120831-3-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.13-rc4).
No conflicts.
Adjacent changes:
drivers/net/ethernet/renesas/rswitch.h
32fd46f5b69e ("net: renesas: rswitch: remove speed from gwca structure")
922b4b955a03 ("net: renesas: rswitch: rework ts tags management")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fwnode_find_mii_timestamper() calls of_parse_phandle_with_fixed_args()
but does not decrement the refcount of the obtained OF node. Add an
of_node_put() call before returning from the function.
This bug was detected by an experimental static analysis tool that I am
developing.
Fixes: bc1bee3b87ee ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218035106.1436405-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
get resource + request_mem_region + ioremap can all be done by a single
function.
Replace them with devm_platform_get_and_ioremap_resource or\
devm_platform_ioremap_resource where res is not used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> # sja1000_platform.c
Link: https://patch.msgid.link/20241203231337.182391-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If an optional resource is found but fails to remap, return on failure.
Avoids any potential problems when using the iomapped resource as the
assumption is that it's available.
Fixes: 23a890d493e3 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241121193152.8966-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c1e ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c41c ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add Unimac mdio compatible string for the special BCM6846
variant.
This variant has a few extra registers compared to other
versions.
Suggested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/linux-devicetree/b542b2e8-115c-4234-a464-e73aa6bece5c@broadcom.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20241012-bcm6846-mdio-v1-2-c703ca83e962@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/mdio to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/0b60d8bfc45a3de8193f953794dda241e11032a9.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There has already been an issue with the handling of early exits from
device_for_each_child() in this driver, and it was solved with commit
b1de5c78ebe9 ("net: mdio: thunder: Add missing fwnode_handle_put()") by
adding a call to fwnode_handle_put() right after the loop.
That solution is valid indeed, but if a new error path with a 'return'
is added to the loop, this solution will fail. A more secure approach
is using the scoped variant of the macro, which automatically
decrements the refcount of the child node when it goes out of scope,
removing the need for explicit calls to fwnode_handle_put().
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240930-net-device_for_each_child_node_scoped-v2-1-35f09333c1d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Was slightly misleading before, because printed is pointer to fwnode,
not to phy device, as placement in message suggested. Include header
for dev_dbg() declaration while at it.
Output before:
[ +0.001247] mdio_bus f802c000.ethernet-ffffffff: registered phy 2612f00a fwnode at address 3
Output after:
[ +0.001229] mdio_bus f802c000.ethernet-ffffffff: registered phy fwnode /ahb/apb/ethernet@f802c000/ethernet-phy@3 at address 3
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://patch.msgid.link/20240906062256.11289-1-ada@thorsis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use the dev_err_probe() helper to simplify code.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Avoids the need for manual cleanup of_node_put() in early exits
from the loop by using for_each_available_child_of_node_scoped().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Replace of_get_property() with the type specific
of_property_count_u32_elems() to get the property length.
This is part of a larger effort to remove callers of of_get_property()
and similar functions. of_get_property() leaks the DT property data
pointer which is a problem for dynamically allocated nodes which may
be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240731201514.1839974-2-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mscc-miim device can be impacted by the switch reset, at least when
this device is part of the LAN966x PCI device.
Handle this newly added (optional) resets property.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace open coded variant of device_is_compatible().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mdio compat string for ASP 2.0 ethernet driver.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
