| Age | Commit message (Collapse) | Author | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fixes from Ulf Hansson:
- rockchip: Fix PD_VCODEC for RK3588
- bcm: Fix broken reset status read for bcm2835
* tag 'pmdomain-v7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: rockchip: Fix PD_VCODEC for RK3588
pmdomain: bcm: bcm2835-power: Fix broken reset status read
|
|
>From the RK3588 TRM Table 7-1 RK3588 Voltage Domain and Power Domain Summary,
PD_RKVDEC0/1 and PD_VENC0/1 rely on VD_VCODEC which require extra voltages to
be applied, otherwise it breaks RK3588-evb1-v10 board after vdec support landed[1].
The panic looks like below:
rockchip-pm-domain fd8d8000.power-management:power-controller: failed to set domain 'rkvdec0' on, val=0
rockchip-pm-domain fd8d8000.power-management:power-controller: failed to set domain 'rkvdec1' on, val=0
...
Hardware name: Rockchip RK3588S EVB1 V10 Board (DT)
Workqueue: pm genpd_power_off_work_fn
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x40/0x84
dump_stack+0x18/0x24
vpanic+0x1ec/0x4fc
vpanic+0x0/0x4fc
check_panic_on_warn+0x0/0x94
arm64_serror_panic+0x6c/0x78
do_serror+0xc4/0xcc
el1h_64_error_handler+0x3c/0x5c
el1h_64_error+0x6c/0x70
regmap_mmio_read32le+0x18/0x24 (P)
regmap_bus_reg_read+0xfc/0x130
regmap_read+0x188/0x1ac
regmap_read+0x54/0x78
rockchip_pd_power+0xcc/0x5f0
rockchip_pd_power_off+0x1c/0x4c
genpd_power_off+0x84/0x120
genpd_power_off+0x1b4/0x260
genpd_power_off_work_fn+0x38/0x58
process_scheduled_works+0x194/0x2c4
worker_thread+0x2ac/0x3d8
kthread+0x104/0x124
ret_from_fork+0x10/0x20
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x3000000,000e0005,40230521,0400720b
Memory Limit: none
---[ end Kernel panic - not syncing: Asynchronous SError Interrupt ]---
Chaoyi pointed out the PD_VCODEC is the parent of PD_RKVDEC0/1 and PD_VENC0/1, so checking
the PD_VCODEC is enough.
[1] https://lore.kernel.org/linux-rockchip/20251020212009.8852-2-detlev.casanova@collabora.com/
Fixes: db6df2e3fc16 ("pmdomain: rockchip: add regulator support")
Cc: stable@vger.kernel.org
Suggested-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
bcm2835_reset_status() has a misplaced parenthesis on every PM_READ()
call. Since PM_READ(reg) expands to readl(power->base + (reg)), the
expression:
PM_READ(PM_GRAFX & PM_V3DRSTN)
computes the bitwise AND of the register offset PM_GRAFX with the
bitmask PM_V3DRSTN before using the result as a register offset, reading
from the wrong MMIO address instead of the intended PM_GRAFX register.
The same issue affects the PM_IMAGE cases.
Fix by moving the closing parenthesis so PM_READ() receives only the
register offset, and the bitmask is applied to the value returned by
the read.
Fixes: 670c672608a1 ("soc: bcm: bcm2835-pm: Add support for power domains under a new binding.")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Passing pm_runtime_put() return value to the callers is not particularly
useful.
Returning an error code from pm_runtime_put() merely means that it has
not queued up a work item to check whether or not the device can be
suspended and there are many perfectly valid situations in which that
can happen, like after writing "on" to the devices' runtime PM "control"
attribute in sysfs for one example.
Accordingly, update imx_pgc_domain_suspend() to simply discard the
return value of pm_runtime_put() and always return success to the
caller.
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/15658107.tv2OnDr8pf@rafael.j.wysocki
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fixes from Ulf Hansson:
- imx:
- Fix system wakeup support for imx8mp power domains
- Fix potential out-of-range access for imx8m power domains
- Fix the imx8mm gpu hang
- qcom: Fix off-by-one error for highest state in rpmpd
* tag 'pmdomain-v6.19-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: imx8mp-blk-ctrl: Keep usb phy power domain on for system wakeup
pmdomain: imx8mp-blk-ctrl: Keep gpc power domain on for system wakeup
pmdomain: imx8m-blk-ctrl: fix out-of-range access of bc->domains
pmdomain: imx: gpcv2: Fix the imx8mm gpu hang due to wrong adb400 reset
pmdomain: qcom: rpmpd: fix off-by-one error in clamping to the highest state
|
|
USB system wakeup need its PHY on, so add the GENPD_FLAG_ACTIVE_WAKEUP
flags to USB PHY genpd configuration.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Fixes: 556f5cf9568a ("soc: imx: add i.MX8MP HSIO blk-ctrl")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Current design will power off all dependent GPC power domains in
imx8mp_blk_ctrl_suspend(), even though the user device has enabled
wakeup capability. The result is that wakeup function never works
for such device.
An example will be USB wakeup on i.MX8MP. PHY device '382f0040.usb-phy'
is attached to power domain 'hsioblk-usb-phy2' which is spawned by hsio
block control. A virtual power domain device 'genpd:3:32f10000.blk-ctrl'
is created to build connection with 'hsioblk-usb-phy2' and it depends on
GPC power domain 'usb-otg2'. If device '382f0040.usb-phy' enable wakeup,
only power domain 'hsioblk-usb-phy2' keeps on during system suspend,
power domain 'usb-otg2' is off all the time. So the wakeup event can't
happen.
In order to further establish a connection between the power domains
related to GPC and block control during system suspend, register a genpd
power on/off notifier for the power_dev. This allows us to prevent the GPC
power domain from being powered off, in case the block control power
domain is kept on to serve system wakeup.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 556f5cf9568a ("soc: imx: add i.MX8MP HSIO blk-ctrl")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix out-of-range access of bc->domains in imx8m_blk_ctrl_remove().
Fixes: 2684ac05a8c4 ("soc: imx: add i.MX8M blk-ctrl driver")
Cc: stable@kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
On i.MX8MM, the GPUMIX, GPU2D, and GPU3D blocks share a common reset
domain. Due to this hardware limitation, powering off/on GPU2D or GPU3D
also triggers a reset of the GPUMIX domain, including its ADB400 port.
However, the ADB400 interface must always be placed into power‑down mode
before being reset.
Currently the GPUMIX and GPU2D/3D power domains rely on runtime PM to
handle dependency ordering. In some corner cases, the GPUMIX power off
sequence is skipped, leaving the ADB400 port active when GPU2D/3D reset.
This causes the GPUMIX ADB400 port to be reset while still active,
leading to unpredictable bus behavior and GPU hangs.
To avoid this, refine the power‑domain control logic so that the GPUMIX
ADB400 port is explicitly powered down and powered up as part of the GPU
power domain on/off sequence. This ensures proper ordering and prevents
incorrect ADB400 reset.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As it is indicated by the comment, the rpmpd_aggregate_corner() function
tries to clamp the state to the highest corner/level supported by the
given power domain, however the calculation of the highest state contains
an off-by-one error.
The 'max_state' member of the 'rpmpd' structure indicates the highest
corner/level, and as such it does not needs to be decremented.
Change the code to use the 'max_state' value directly to avoid the error.
Fixes: 98c8b3efacae ("soc: qcom: rpmpd: Add sync_state")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fixes from Ulf Hansson:
- imx: Remove incorrect reset/clock mask for 8mq vpu
- rockchip: Fix initial state of PM domain
* tag 'pmdomain-v6.19-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain:rockchip: Fix init genpd as GENPD_STATE_ON before regulator ready
pmdomain: imx8m-blk-ctrl: Remove separate rst and clk mask for 8mq vpu
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm Arm64 DeviceTree fixes for v6.19
Add missing power-domains to the SC8280XP RPM power-domain and ensure
these are voted for from the remoteproc instances while powering them
up.
Clear a couple of DeviceTree validation warnings in SM8550 and SM8650
USB controller nodes.
Specify the correct display panel on the OnePlus 6.
Correct the UFS clock mapping on Talos, to ensure UFS is properly
clocked.
Add Abel's old emails address to .mailmap.
* tag 'qcom-arm64-fixes-for-6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sm8650: Fix compile warnings in USB controller node
arm64: dts: qcom: sm8550: Fix compile warnings in USB controller node
arm64: dts: qcom: sc8280xp: Add missing VDD_MXC links
pmdomain: qcom: rpmhpd: Add MXC to SC8280XP
dt-bindings: power: qcom,rpmpd: Add SC8280XP_MXC_AO
arm64: dts qcom: sdm845-oneplus-enchilada: Specify panel name within the compatible
mailmap: Update email address for Abel Vesa
arm64: dts: qcom: talos: Correct UFS clocks ordering
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
RK3588_PD_NPU initialize as GENPD_STATE_ON before regulator ready.
rknn_iommu initlized success and suspend RK3588_PD_NPU. When rocket
driver register, it will resume rknn_iommu.
If regulator is still not ready at this point, rknn_iommu resume fail,
pm runtime status will be error: -EPROBE_DEFER.
This patch set pmdomain to off if it need regulator during probe,
consumer device can power on pmdomain after regulator ready.
Signed-off-by: Frank Zhang <rmxpzlb@gmail.com>
Tested-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes: db6df2e3fc16 ("pmdomain: rockchip: add regulator support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For i.MX8MQ platform, the ADB in the VPUMIX domain has no separate reset
and clock enable bits, but is ungated and reset together with the VPUs.
So we can't reset G1 or G2 separately, it may led to the system hang.
Remove rst_mask and clk_mask of imx8mq_vpu_blk_ctl_domain_data.
Let imx8mq_vpu_power_notifier() do really vpu reset.
Fixes: 608d7c325e85 ("soc: imx: imx8m-blk-ctrl: add i.MX8MQ VPU blk-ctrl")
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
of_get_child_by_name() returns a node pointer with refcount incremented.
Use the __free() attribute to manage the pgc_node reference, ensuring
automatic of_node_put() cleanup when pgc_node goes out of scope.
This eliminates the need for explicit error handling paths and avoids
reference count leaks.
Fixes: 721cabf6c660 ("soc: imx: move PGC handling to a new GPC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove scpsys_get_legacy_regmap(), replacing its usage with
of_find_node_with_property(). Explicitly call of_node_get(np) before each
of_find_node_with_property() to maintain correct node reference counting.
The of_find_node_with_property() function "consumes" its input by calling
of_node_put() internally, whether or not it finds a match. Currently,
dev->of_node (np) is passed multiple times in sequence without incrementing
its reference count, causing it to be decremented multiple times and
risking early memory release.
Adding of_node_get(np) before each call balances the reference count,
preventing premature node release.
Fixes: c1bac49fe91f ("pmdomains: mtk-pm-domains: Fix spinlock recursion in probe")
Cc: stable@vger.kernel.org
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Tested-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This was apparently accounted for in dt-bindings, but never made its
way into the driver.
Fix it for SC8280XP and its VDD_GFX-less cousin, SA8540P.
Fixes: f68f1cb3437d ("soc: qcom: rpmhpd: add sc8280xp & sa8540p rpmh power-domains")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20251202-topic-8280_mxc-v2-2-46cdf47a829e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"pmdomain core:
- Allow power-off for out-of-band wakeup-capable devices
- Drop the redundant call to dev_pm_domain_detach() for the amba bus
- Extend the genpd governor for CPUs to account for IPIs
pmdomain providers:
- bcm: Add support for BCM2712
- mediatek: Add support for MFlexGraphics power domains
- mediatek: Add support for MT8196 power domains
- qcom: Add RPMh power domain support for Kaanapali
- rockchip: Add support for RV1126B
pmdomain consumers:
- usb: dwc3: Enable out of band wakeup for i.MX95
- usb: chipidea: Enable out of band wakeup for i.MX95"
* tag 'pmdomain-v6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (26 commits)
pmdomain: Extend the genpd governor for CPUs to account for IPIs
smp: Introduce a helper function to check for pending IPIs
pmdomain: mediatek: convert from clk round_rate() to determine_rate()
amba: bus: Drop dev_pm_domain_detach() call
pmdomain: bcm: bcm2835-power: Prepare to support BCM2712
pmdomain: mediatek: mtk-mfg: select MAILBOX in Kconfig
pmdomain: mediatek: Add support for MFlexGraphics
pmdomain: mediatek: Fix build-errors
cpuidle: psci: Replace deprecated strcpy in psci_idle_init_cpu
pmdomain: rockchip: Add support for RV1126B
pmdomain: mediatek: Add support for MT8196 HFRPSYS power domains
pmdomain: mediatek: Add support for MT8196 SCPSYS power domains
pmdomain: mediatek: Add support for secure HWCCF infra power on
pmdomain: mediatek: Add support for Hardware Voter power domains
pmdomain: qcom: rpmhpd: Add RPMh power domain support for Kaanapali
usb: dwc3: imx8mp: Set out of band wakeup for i.MX95
usb: chipidea: ci_hdrc_imx: Set out of band wakeup for i.MX95
usb: chipidea: core: detach power domain for ci_hdrc platform device
pmdomain: core: Allow power-off for out-of-band wakeup-capable devices
PM: wakeup: Add out-of-band system wakeup support for devices
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are quite a few interesting things here, including new hardware
support, new features, some bug fixes and documentation updates. In
addition, there are a usual bunch of minor fixes and cleanups all
over.
In the new hardware support category, there are intel_pstate and
intel_rapl driver updates to support new processors, Panther Lake,
Wildcat Lake, Noval Lake, and Diamond Rapids in the OOB mode, OPP and
bandwidth allocation support in the tegra186 cpufreq driver, and
JH7110S SOC support in dt-platdev cpufreq.
The new features are the PM QoS CPU latency limit for suspend-to-idle,
the netlink support for the energy model management, support for
terminating system suspend via a wakeup event during the sync of file
systems, configurable number of hibernation compression threads, the
runtime PM auto-cleanup macros, and the "poweroff" PM event that is
expected to be used during system shutdown.
Bugs are mostly fixed in cpuidle governors, but there are also fixes
elsewhere, like in the amd-pstate cpufreq driver.
Documentation updates include, but are not limited to, a new doc on
debugging shutdown hangs, cross-referencing fixes and cleanups in the
intel_pstate documentation, and updates of comments in the core
hibernation code.
Specifics:
- Introduce and document a QoS limit on CPU exit latency during
wakeup from suspend-to-idle (Ulf Hansson)
- Add support for building libcpupower statically (Zuo An)
- Add support for sending netlink notifications to user space on
energy model updates (Changwoo Mini, Peng Fan)
- Minor improvements to the Rust OPP interface (Tamir Duberstein)
- Fixes to scope-based pointers in the OPP library (Viresh Kumar)
- Use residency threshold in polling state override decisions in the
menu cpuidle governor (Aboorva Devarajan)
- Add sanity check for exit latency and target residency in the
cpufreq core (Rafael Wysocki)
- Use this_cpu_ptr() where possible in the teo governor (Christian
Loehle)
- Rework the handling of tick wakeups in the teo cpuidle governor to
increase the likelihood of stopping the scheduler tick in the cases
when tick wakeups can be counted as non-timer ones (Rafael Wysocki)
- Fix a reverse condition in the teo cpuidle governor and drop a
misguided target residency check from it (Rafael Wysocki)
- Clean up multiple minor defects in the teo cpuidle governor (Rafael
Wysocki)
- Update header inclusion to make it follow the Include What You Use
principle (Andy Shevchenko)
- Enable MSR-based RAPL PMU support in the intel_rapl power capping
driver and arrange for using it on the Panther Lake and Wildcat
Lake processors (Kuppuswamy Sathyanarayanan)
- Add support for Nova Lake and Wildcat Lake processors to the
intel_rapl power capping driver (Kaushlendra Kumar, Srinivas
Pandruvada)
- Add OPP and bandwidth support for Tegra186 (Aaron Kling)
- Optimizations for parameter array handling in the amd-pstate
cpufreq driver (Mario Limonciello)
- Fix for mode changes with offline CPUs in the amd-pstate cpufreq
driver (Gautham Shenoy)
- Preserve freq_table_sorted across suspend/hibernate in the cpufreq
core (Zihuan Zhang)
- Adjust energy model rules for Intel hybrid platforms in the
intel_pstate cpufreq driver and improve printing of debug messages
in it (Rafael Wysocki)
- Replace deprecated strcpy() in cpufreq_unregister_governor()
(Thorsten Blum)
- Fix duplicate hyperlink target errors in the intel_pstate cpufreq
driver documentation and use :ref: directive for internal linking
in it (Swaraj Gaikwad, Bagas Sanjaya)
- Add Diamond Rapids OOB mode support to the intel_pstate cpufreq
driver (Kuppuswamy Sathyanarayanan)
- Use mutex guard for driver locking in the intel_pstate driver and
eliminate some code duplication from it (Rafael Wysocki)
- Replace udelay() with usleep_range() in ACPI cpufreq (Kaushlendra
Kumar)
- Minor improvements to various cpufreq drivers (Christian Marangi,
Hal Feng, Jie Zhan, Marco Crivellari, Miaoqian Lin, and Shuhao Fu)
- Replace snprintf() with scnprintf() in show_trace_dev_match()
(Kaushlendra Kumar)
- Fix memory allocation error handling in pm_vt_switch_required()
(Malaya Kumar Rout)
- Introduce CALL_PM_OP() macro and use it to simplify code in generic
PM operations (Kaushlendra Kumar)
- Add module param to backtrace all CPUs in the device power
management watchdog (Sergey Senozhatsky)
- Rework message printing in swsusp_save() (Rafael Wysocki)
- Make it possible to change the number of hibernation compression
threads (Xueqin Luo)
- Clarify that only cgroup1 freezer uses PM freezer (Tejun Heo)
- Add document on debugging shutdown hangs to PM documentation and
correct a mistaken configuration option in it (Mario Limonciello)
- Shut down wakeup source timer before removing the wakeup source
from the list (Kaushlendra Kumar, Rafael Wysocki)
- Introduce new PMSG_POWEROFF event for system shutdown handling with
the help of PM device callbacks (Mario Limonciello)
- Make pm_test delay interruptible by wakeup events (Riwen Lu)
- Clean up kernel-doc comment style usage in the core hibernation
code and remove unuseful comments from it (Sunday Adelodun, Rafael
Wysocki)
- Add support for handling wakeup events and aborting the suspend
process while it is syncing file systems (Samuel Wu, Rafael
Wysocki)
- Add WQ_UNBOUND to pm_wq workqueue (Marco Crivellari)
- Add runtime PM wrapper macros for ACQUIRE()/ACQUIRE_ERR() and use
them in the PCI core and the ACPI TAD driver (Rafael Wysocki)
- Improve runtime PM in the ACPI TAD driver (Rafael Wysocki)
- Update pm_runtime_allow/forbid() documentation (Rafael Wysocki)
- Fix typos in runtime.c comments (Malaya Kumar Rout)
- Move governor.h from devfreq under include/linux/ and rename to
devfreq-governor.h to allow devfreq governor definitions in out of
drivers/devfreq/ (Dmitry Baryshkov)
- Use min() to improve readability in tegra30-devfreq.c (Thorsten
Blum)
- Fix potential use-after-free issue of OPP handling in
hisi_uncore_freq.c (Pengjie Zhang)
- Fix typo in DFSO_DOWNDIFFERENTIAL macro name in
governor_simpleondemand.c in devfreq (Riwen Lu)"
* tag 'pm-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (96 commits)
PM / devfreq: Fix typo in DFSO_DOWNDIFFERENTIAL macro name
cpuidle: Warn instead of bailing out if target residency check fails
cpuidle: Update header inclusion
Documentation: power/cpuidle: Document the CPU system wakeup latency QoS
cpuidle: Respect the CPU system wakeup QoS limit for cpuidle
sched: idle: Respect the CPU system wakeup QoS limit for s2idle
pmdomain: Respect the CPU system wakeup QoS limit for cpuidle
pmdomain: Respect the CPU system wakeup QoS limit for s2idle
PM: QoS: Introduce a CPU system wakeup QoS limit
cpuidle: governors: teo: Add missing space to the description
PM: hibernate: Extra cleanup of comments in swap handling code
PM / devfreq: tegra30: use min to simplify actmon_cpu_to_emc_rate
PM / devfreq: hisi: Fix potential UAF in OPP handling
PM / devfreq: Move governor.h to a public header location
powercap: intel_rapl: Enable MSR-based RAPL PMU support
powercap: intel_rapl: Prepare read_raw() interface for atomic-context callers
cpufreq: qcom-nvmem: fix compilation warning for qcom_cpufreq_ipq806x_match_list
PM: sleep: Call pm_sleep_fs_sync() instead of ksys_sync_helper()
PM: sleep: Add support for wakeup during filesystem sync
cpufreq: ACPI: Replace udelay() with usleep_range()
...
|
|
The CPU system wakeup QoS limit must be respected for the regular cpuidle
state selection. Therefore, let's extend the genpd governor for CPUs to
take the constraint into account when it selects a domain idle state for
the corresponding PM domain.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman (TI) <khilman@baylibre.com>
Tested-by: Kevin Hilman (TI) <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20251125112650.329269-4-ulf.hansson@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A CPU system wakeup QoS limit may have been requested by user space. To
avoid breaking this constraint when entering a low power state during
s2idle through genpd, let's extend the corresponding genpd governor for
CPUs. More precisely, during s2idle let the genpd governor select a
suitable domain idle state, by taking into account the QoS limit.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman (TI) <khilman@baylibre.com>
Tested-by: Kevin Hilman (TI) <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20251125112650.329269-3-ulf.hansson@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Merge the pmdomain fixes for v6.18-rc[n] into the next branch, to allow
them to get tested together with the new changes that are targeted for
v6.19.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit 13a4b7fb6260 ("pmdomain: core: Leave powered-on genpds on until
late_initcall_sync") kept power-domains on longer during boot which is
causing some GPU related tests to fail on Tegra234. While this is being
investigated, add the flag GENPD_FLAG_NO_STAY_ON for Tegra devices to
restore the previous behaviour to fix this.
Fixes: 13a4b7fb6260 ("pmdomain: core: Leave powered-on genpds on until late_initcall_sync")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For some reason, of_find_node_with_property() is creating a spinlock
recursion issue along with fwnode_count_parents(), and this issue
is making all MediaTek boards unbootable.
As of kernel v6.18-rc6, there are only three users of this function,
one of which is this driver.
Migrate away from of_find_node_with_property() by adding a local
scpsys_get_legacy_regmap_node() function, which acts similarly to
of_find_node_with_property(), and calling the former in place of
the latter.
This resolves the following spinlock recursion issue:
[ 1.773979] BUG: spinlock recursion on CPU#2, kworker/u24:1/60
[ 1.790485] lock: devtree_lock+0x0/0x40, .magic: dead4ead, .owner: kworker/u24:1/60, .owner_cpu: 2
[ 1.791644] CPU: 2 UID: 0 PID: 60 Comm: kworker/u24:1 Tainted: G W 6.18.0-rc6 #3 PREEMPT
[ 1.791649] Tainted: [W]=WARN
[ 1.791650] Hardware name: MediaTek Genio-510 EVK (DT)
[ 1.791653] Workqueue: events_unbound deferred_probe_work_func
[ 1.791658] Call trace:
[ 1.791659] show_stack+0x18/0x30 (C)
[ 1.791664] dump_stack_lvl+0x68/0x94
[ 1.791668] dump_stack+0x18/0x24
[ 1.791672] spin_dump+0x78/0x88
[ 1.791678] do_raw_spin_lock+0x110/0x140
[ 1.791684] _raw_spin_lock_irqsave+0x58/0x6c
[ 1.791690] of_get_parent+0x28/0x74
[ 1.791694] of_fwnode_get_parent+0x38/0x7c
[ 1.791700] fwnode_count_parents+0x34/0xf0
[ 1.791705] fwnode_full_name_string+0x28/0x120
[ 1.791710] device_node_string+0x3e4/0x50c
[ 1.791715] pointer+0x294/0x430
[ 1.791718] vsnprintf+0x21c/0x5bc
[ 1.791722] vprintk_store+0x108/0x47c
[ 1.791728] vprintk_emit+0xc4/0x350
[ 1.791732] vprintk_default+0x34/0x40
[ 1.791736] vprintk+0x24/0x30
[ 1.791740] _printk+0x60/0x8c
[ 1.791744] of_node_release+0x154/0x194
[ 1.791749] kobject_put+0xa0/0x120
[ 1.791753] of_node_put+0x18/0x28
[ 1.791756] of_find_node_with_property+0x74/0x100
[ 1.791761] scpsys_probe+0x338/0x5e0
[ 1.791765] platform_probe+0x5c/0xa4
[ 1.791770] really_probe+0xbc/0x2ac
[ 1.791774] __driver_probe_device+0x78/0x118
[ 1.791779] driver_probe_device+0x3c/0x170
[ 1.791783] __device_attach_driver+0xb8/0x150
[ 1.791788] bus_for_each_drv+0x88/0xe8
[ 1.791792] __device_attach+0x9c/0x1a0
[ 1.791796] device_initial_probe+0x14/0x20
[ 1.791801] bus_probe_device+0xa0/0xa4
[ 1.791805] deferred_probe_work_func+0x88/0xd0
[ 1.791809] process_one_work+0x1e8/0x448
[ 1.791813] worker_thread+0x1ac/0x340
[ 1.791816] kthread+0x138/0x220
[ 1.791821] ret_from_fork+0x10/0x20
Fixes: c29345fa5f66 ("pmdomain: mediatek: Refactor bus protection regmaps retrieval")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When the genpd governor for CPUs, tries to select the most optimal idle
state for a group of CPUs managed in a PM domain, it fails far too often.
On a Dragonboard 410c, which is an arm64 based platform with 4 CPUs in one
cluster that is using PSCI OS-initiated mode, we can observe that we often
fail when trying to enter the selected idle state. This is certainly a
suboptimal behaviour that leads to many unnecessary requests being sent to
the PSCI FW.
A simple dd operation that reads from the eMMC, to generate some IRQs and
I/O handling helps us to understand the problem, while also monitoring the
rejected counters in debugfs for the corresponding idle states of the genpd
in question.
Menu governor:
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 1451 437 91 149 0
S1 65194 558 149 172 0
dd if=/dev/mmcblk0 of=/dev/null bs=1M count=500
524288000 bytes (500.0MB) copied, 3.562698 seconds, 140.3MB/s
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 2694 1073 265 892 1
S1 74567 829 561 790 0
The dd completed in ~3.6 seconds and rejects increased with 586.
Teo governor:
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 4976 2096 392 1721 2
S1 160661 1893 1309 1904 0
dd if=/dev/mmcblk0 of=/dev/null bs=1M count=500
524288000 bytes (500.0MB) copied, 3.543225 seconds, 141.1MB/s
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 5192 2194 433 1830 2
S1 167677 2891 3184 4729 0
The dd completed in ~3.6 seconds and rejects increased with 1916.
The main reason to the above problem is pending IPIs for one of the CPUs
that is affected by the idle state that the genpd governor selected. This
leads to that the PSCI FW refuses to enter it. To improve the behaviour,
let's start to take into account pending IPIs for CPUs in the genpd
governor, hence we fallback to use the shallower per CPU idle state.
Re-testing with this change shows a significant improved behaviour.
- Menu governor:
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 2556 878 19 368 1
S1 69974 596 10 152 0
dd if=/dev/mmcblk0 of=/dev/null bs=1M count=500
524288000 bytes (500.0MB) copied, 3.522010 seconds, 142.0MB/s
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 3360 1320 28 819 1
S1 70168 710 11 267 0
The dd completed in ~3.5 seconds and rejects increased with 10.
- Teo governor
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 5145 1861 39 938 1
S1 188887 3117 51 1975 0
dd if=/dev/mmcblk0 of=/dev/null bs=1M count=500
524288000 bytes (500.0MB) copied, 3.653100 seconds, 136.9MB/s
cat /sys/kernel/debug/pm_genpd/power-domain-cluster/idle_states
State Time Spent(ms) Usage Rejected Above Below
S0 5260 1923 42 1002 1
S1 190849 4033 52 2892 0
The dd completed in ~3.7 seconds and rejects increased with 4.
Note that, the rejected counters in genpd are also being accumulated in the
rejected counters that are managed by cpuidle, yet on a per CPU idle states
basis. Comparing these counters before/after this change, through cpuidle's
sysfs interface shows the similar improvements.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The round_rate() clk ops is deprecated in the clk framework in favor
of the determine_rate() clk ops, so let's convert this driver so that
round_rate() can be removed from the clk core.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
BCM2712 has a PM block but lacks asb and rpivid_asb register
spaces. To avoid unwanted results add a check for asb existence
during probe and also add a new register offset for bcm2712 to
control grafx_v3d power domain. The decision to use the new
register is implicit - if asb register base is null then the
driver is probed for bcm2712 (the other supported SoCs have
asb register space).
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The mtk-mfg pmdomain driver calls common mailbox framework functions. If
the common mailbox framework is not selected in the kernel's
configuration, the build runs into a linker error, as the symbols are
absent.
The hardware mailbox Kconfig system, MAILBOX, has no dependencies of its
own. It's therefore safe to "select" it rather than use "depend on".
Declare this "select" dependency in the Kconfig for the driver.
Fixes: 1ff1f0db6aec ("pmdomain: mediatek: Add support for MFlexGraphics")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202510301311.TcOCnZ1s-lkp@intel.com/
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Various MediaTek SoCs use GPU integration silicon named "MFlexGraphics"
by MediaTek. On the MT8196 and MT6991 SoCs, interacting with this
integration silicon is required to power on the GPU.
This glue silicon is in the form of an embedded microcontroller running
special-purpose firmware, which autonomously adjusts clocks and
regulators.
Implement a driver, modelled as a pmdomain driver with a
set_performance_state operation, to support these SoCs.
The driver also exposes the actual achieved clock rate, as read back
from the MCU, as common clock framework clocks, by acting as a clock
provider as well.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Let's add the missing header to fix the reported build-errors.
Fixes: df4e9ec1ed86 ("pmdomain: mediatek: Add support for secure HWCCF infra power on")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202510231317.ZZxNaFG0-lkp@intel.com/
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add configuration and power domains for RV1126 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for the HFRPSYS Multimedia power domains found in the
MediaTek MT8196 Chromebook SoC.
Those power domains are all managed by the Hardware Voter MCU.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add a new SPM bus protection block and add support for both the
direct control and HW Voter control SCPSYS power domains found
in the MT8196 and MT6991 SoCs.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some SoCs, like the MediaTek Dimensity 9400 (MT6991), have granular
power controls and will disable power to the infracfg to save power
when the platform is in deeper sleep states (or when no IP in the
the infracfg macro-block is in use).
These chips also cannot control the infracfg power states directly
via AP register writes as those are protected by the secure world.
Add a new MTK_SCPD_INFRA_PWR_CTL cap and, if present, make a call
to the secure world to poweron the infracfg block, as the HWV IP
resides in there, when executing HWV domains power sequences.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
New generation SoCs like MT8196/MT6991 feature a new type of power
domains, managed by a Hardware Voter (HWV) helper (through a SoC
internal fixed-function MCU): this is used to collect votes from
both the AP and the various other remote processors present in the
SoC and transparently power on/off various power domains, avoiding
unpowered access of registers in various internal IPs from all of
the integrated remote processors (or from the AP...!).
Add a new power domain type and differentiate between the old
SCPSYS_MTCMOS_TYPE_DIRECT_CTL - where power domains are controlled
directly by and exclusively from the Application Processor, and
the new SCPSYS_MTCMOS_TYPE_HW_VOTER, where the power domains are
voted through the HWV.
With the two needing different handling, check the power domain
type and assign a different power_{off,on} callback for pm_genpd:
for this specific reason, also move the check for the SCPD cap
MTK_SCPD_KEEP_DEFAULT_OFF after the assignment, and use the
assigned power_on function instead of calling scpsys_power_on()
directly to make that work for both HW_VOTER and DIRECT_CTL.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add the RPMh power domains present in Kaanapali SoCs. Also increase the
maximum allowed number of levels for ARC resources from 16 to 32, as
needed starting on the Kaanapali SoC where the ARC vote registers have been
expanded from 4 to 5 bits.
Signed-off-by: Jishnu Prakash <jishnu.prakash@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently, if a device is configured as a system wakeup source, the PM
domain core avoids powering off its power domain during system-wide
suspend. However, this can lead to unnecessary power consumption,
especially for devices whose wakeup logic resides in an always-on domain,
i.e., devices with out-of-band wakeup capability.
To address this, add a check for device_out_band_wakeup() in
genpd_finish_suspend(). If the device supports out-of-band wakeup, its
power domain can be safely powered off, just like regular devices without
wakeup enabled. And same check in genpd_finish_resume().
This change improves power efficiency without compromising wakeup
functionality.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
of_get_child_by_name() returns a node pointer with refcount incremented, we
should use of_node_put() on it when not needed anymore. Add the missing
of_node_put() to avoid refcount leak.
Fixes: 721cabf6c660 ("soc: imx: move PGC handling to a new GPC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Limit the workaround for the lack of the proper splash-screen handover
handling to the legacy ARM 32bit systems and replace forcing a sync_state
by explicite power domain shutdown. This approach lets compiler to
optimize it out on newer ARM 64bit systems.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 0745658aebbe ("pmdomain: samsung: Fix splash-screen handover by enforcing a sync_state")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If of_genpd_add_provider_onecell() fails during probe, the previously
created generic power domains are not removed, leading to a memory leak
and potential kernel crash later in genpd_debug_add().
Add proper error handling to unwind the initialized domains before
returning from probe to ensure all resources are correctly released on
failure.
Example crash trace observed without this fix:
| Unable to handle kernel paging request at virtual address fffffffffffffc70
| CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.18.0-rc1 #405 PREEMPT
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform
| pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : genpd_debug_add+0x2c/0x160
| lr : genpd_debug_init+0x74/0x98
| Call trace:
| genpd_debug_add+0x2c/0x160 (P)
| genpd_debug_init+0x74/0x98
| do_one_initcall+0xd0/0x2d8
| do_initcall_level+0xa0/0x140
| do_initcalls+0x60/0xa8
| do_basic_setup+0x28/0x40
| kernel_init_freeable+0xe8/0x170
| kernel_init+0x2c/0x140
| ret_from_fork+0x10/0x20
Fixes: 898216c97ed2 ("firmware: arm_scmi: add device power domain support using genpd")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
of_genpd_add_provider_simple() could fail, in which case this code
leaks the domain name, pd->pd.name.
Use devm_kstrdup_const() to plug this leak. As a side-effect, we can
simplify existing error handling.
Fixes: c09a3e6c97f0 ("soc: samsung: pm_domains: Convert to regular platform driver")
Cc: stable@vger.kernel.org
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
|
|
The devm_auxiliary_device_create() returns NULL on error. It never
returns error pointers. Using PTR_ERR_OR_ZERO() here means the function
always returns success. Replace the PTR_ERR_OR_ZERO() call check with
a NULL check.
Fixes: 64581f41f4c4 ("pmdomain: thead: create auxiliary device for rebooting")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Merge the pmdomain fixes for v6.17-rc[n] into the next branch, to allow
them to get tested together with the new changes that are targeted for
v6.18.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In MT8195 power domain data array, set the KEEP_DEFAULT_OFF and
ACTIVE_WAKEUP flags for the AUDIO power domain entry to avoid
having this domain being on during boot sequence when unneeded.
Fixes: 0e789b491ba0 ("pmdomain: core: Leave powered-on genpds on until sync_state")
Fixes: 13a4b7fb6260 ("pmdomain: core: Leave powered-on genpds on until late_initcall_sync")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The reboot / power off operations require communication with the AON
firmware too.
As the driver is already present, create an auxiliary device with name
"reboot" to match that driver, and pass the AON channel by using
platform_data.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After discussion with the devicetree maintainers we agreed to not extend
lists with the generic compatible "apple,pmgr-pwrstate" anymore [1]. Use
"apple,t8103-pmgr-pwrstate" as base compatible as it is the SoC the
driver and bindings were written for.
[1]: https://lore.kernel.org/asahi/12ab93b7-1fc2-4ce0-926e-c8141cfe81bf@kernel.org/
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sven Peter <sven@kernel.org>
|
|
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
appended to the "under-the-cut" portion of the patch.
Note that prior to running the Coccinelle,
airoha_cpu_pmdomain_clk_round() was renamed to
airoha_cpu_pmdomain_clk_round_rate().
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
